1、BRITISH STANDARD BS EN 60264-2-3:1996 IEC 60264-2-3: 1990 Incorporating Amendment No. 1 to BS 7584-2.3:1992 (renumbers the BS as BS EN 60264-2-3: 1996) and incorporating Amendment No. 2 Packaging of winding wires Part 2-3: Cylindrical barrelled delivery spools Specification for non-returnable spools
2、 made from thermoplastic material The European Standard EN 60264-2-3:1994, with the incorporation of amendment A1:2004, has the status of a British Standard ICS 29.060.10 BS EN 60264-2-3:1996 This British Standard, having been prepared under the direction of the Cables and Insulation Standards Polic
3、y Committee, was published under the authority of the Standards Board and comes into effect on 15 August 1992 BSI 5 May 2004 The following BSI references relate to the work on this standard: Committee reference CIL/55 Draft announced in BSI News May 1992 ISBN 0 580 21071 5 Committees responsible for
4、 this British Standard The preparation of this British Standard was entrusted by the Cables and Insulation Standards Policy Committee (CIL/-) to Technical Committee CIL/55, upon which the following bodies were represented: British Cable Makers Confederation British Non-ferrous Metals Federation Brit
5、ish Railways Board Covered Conductors Association EEA (the Association of Electronics, Telecommunications and Business Equipment Industries) Electrical and Electronic Insulation Association Electronic Components Industry Federation Transmission and Distribution Association (BEAMA Ltd.) Amendments is
6、sued since publication Amd. No. Date Comments 9050 May 1996 15099 5 May 2004 See national forewordBS EN 60264-2-3:1996 BSI 5 May 2004 i Contents Page Committees responsible Inside front cover National foreword ii 1S c o p e 3 2 Normative references 3 3M a t e r i a l 3 4T y p e d e s i g n a t i o n
7、 3 5R e q u i r e m e n t s 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications 6 Table 1 4 Table 2 4 Table 3 5 Table 4 5BS EN 60264-2-3:1996 ii BSI 5 May 2004 National foreword This British Standard has been prepared by Technical
8、Committee GEL/55 (formerly CIL/55) and is the English language version of EN 60264-2-3:1994 Packaging of winding wires Part 2-3: Cylindrical barrelled delivery spools Specification for non-returnable spools made from thermoplastic material, including amendment A1:2004, published by the European Comm
9、ittee for Electrotechnical Standardization (CENELEC). It is identical with IEC 60264-2-3:1990, including amendment 1, published by the International Electrotechnical Commission (IEC). The start and finish of text introduced or altered by amendment is indicated in the text by tags !“. Tags indicating
10、 changes to CENELEC text carry the number of the CENELEC amendment. For example, text altered by CENELEC amendment A1 is indicated by !“. BS EN 60264, of which there are four Parts, deals with the packaging of winding wires. Part 1 covers containers, Part 2 covers cylindrical barrelled delivery spoo
11、ls, Part 3 covers taper barrelled delivery spools and Part 4 covers methods of test. This British Standard is one of a series dealing with insulated wires used for windings in electrical equipment, which comprises the following three groups. IEC 60851, Methods of test for winding wires; IEC 60317, S
12、pecifications for particular types of winding wires; IEC 60264, Packaging of winding wires. NOTE BS 6811 Winding wires Part 0:1993 General introduction and list of Parts lists the various Sections of BS 6811 and BS 7584 against the corresponding Parts of the IEC standards listed above. Some or all o
13、f these IEC standards will be adopted as BS ENs in due course and the relevant Parts of BS 6811 and BS 7584 will be renumbered as BS ENs. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under
14、 the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct appli
15、cation. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copyright notice displa
16、yed in this document indicates when the document was last issued.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60264-2-3 December 1994 + A1 March 2004 ICS 29.060.10 Supersedes HD 46.2.3 S1:1992 Descriptors: Winding, electric wire, insulated wire, delivery, spool, packaging, thermoplastic, spe
17、cification, marking English version Packaging of winding wires Part 2-3: Cylindrical barrelled delivery spools Specification for non-returnable spools made from thermoplastic material (includes amendment A1:2004) (IEC 60264-2-3:1990 + A1:2003) Conditionnement des fils de bobinage Partie 2-3: Bobines
18、 de livraison ft de forme cylindrique Spcification pour les bobines non rutilisables, faites de matriau thermoplastique (inclut lamendement A1:2004) (CEI 60264-2-3:1990 + A1:2003) Verpackung von Wickeldrhten Teil 2-3: Lieferspulen mit zylindrischem Kern Spezifikation fr Einweg-Lieferspulen aus therm
19、oplastischem Werkstoff (enthlt nderung A1:2004) (IEC 60264-2-3:1990 + A1:2003) This European Standard was approved by CENELEC on1994-09-01; amendment A1 was approved by CENELEC on 2004-03-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions
20、 for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three o
21、fficial versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical c
22、ommittees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. CENELEC Europea
23、n Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1994 Copyright reserved to CENELEC members Ref. No. EN 60264-2-3:1994 + A1:2004 EEN 60264-2-3:199
24、4 BSI 5 May 2004 2 Foreword The text of the International Standard IEC 264-2-3:1990, prepared by IEC TC 55, Winding wires, was approved by CENELEC as HD 46.2.3 S1 on 1992-06-16. This Harmonization Document was submitted to the formal vote for conversion into a European Standard and was approved by C
25、ENELEC as EN 60264-2-3 on 1994-09-01. The following date was fixed: Annexes designated “normative” are part of the body of the standard. In this standard, Annex ZA is normative. Annex ZA has been added by CENELEC. Foreword to amendment A1 The text of document 55/870/FDIS, future amendment 1 to IEC 6
26、0264-2-3:1990, prepared by IEC TC 55, Winding wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 60264-2-3:1994 on 2004-03-01. The following dates were fixed: Annex ZA has been added by CENELEC. latest date by which the EN has to be implemented at
27、 national level by publication of an identical national standard or by endorsement (dop) 1995-10-15 latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2004-12-01 latest date by which the national standar
28、ds conflicting with the amendment have to be withdrawn (dow) 2007-03-01EN 60264-2-3:1994 BSI 5 May 2004 3 1 Scope This International Standard specifies the requirements for non-returnable cylindrical barrelled delivery spools made from thermoplastic material. 2 Normative references The following sta
29、ndards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged t
30、o investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. IEC 60264-2-1:1989, Packaging of winding wires Part 2: Cylindrical barrelled delivery spools Section 1: Basic dim
31、ensions !IEC 60264-4-1:1997 “, Packaging of winding wires Part 4: Methods of test Section 1: Delivery spools made from thermoplastic material 3 Material The spools shall be made from a thermoplastic material (for example modified polystyrene) that satisfies the requirements given in this standard. T
32、he materials used shall not have a deleterious effect on the conductor or the covering of the winding wire. 4 Type designation Cylindrical barrelled delivery spools according to this standard shall be identified by dimension d 1as specified in IEC 60264-2-1, for example as follows: Delivery spool !6
33、0264-2-3/200 “. 5 Requirements For test methods, see IEC 60264-4-1. 5.1 Spool irregularities 5.1.1 Surface The surface of the spool shall be smooth and the flanges free from protruding material liable to damage the wire or injure the hands of the winding operator. 5.1.2 Construction Bolts and screws
34、, if used in the construction of the spools, shall be countersunk so that the heads are below the surface. 5.2 Spool marking Each spool shall have embossed and/or engraved markings, located on top side of the upper flange, containing the following information: a) the type designation of the spool (f
35、or example !60264-2-3/200 “); b) name and trade mark of the spool manufacturer; c) year of manufacture; d) the nominal mass of the spool in grams; e) the words: “non-returnable”. The top flange shall be of such design as to allow the application of labels giving details of the manufacturer of the wi
36、nding wire, its size, the !mass “ of winding wire on the spool, etc.EN 60264-2-3:1994 4 BSI 5 May 2004 5.3 Mass The mass of the spool shall comply with the value given in Table 1. There are no requirements for other spools. Table 1 5.4 Spool dimensions The spool dimensions and tolerances shall compl
37、y with the dimensions and tolerances given in IEC 60264-2-1. 5.5 True running deviations The true running deviations shall not exceed the value given in Table 1 of IEC 60264-2-1 (under y and z). 5.6 Behaviour at high temperature The spool shall be conditioned !at a temperature of (60 3) C “. The spo
38、ol dimensions and tolerances shall comply with the dimensions and tolerances given in IEC 60264-2-1. No swelling, buckling or variation in the flanges or in the barrel is permitted. 5.7 Impact test on flanges 5.7.1 Under normal ambient conditions The function of the spool shall not be destroyed afte
39、r stressing with the value given in Table 2. There are no requirements for other spools. Table 2 5.7.2 At low temperature The spool shall be conditioned at a temperature from p10 C to p12 C. The function of the spool shall not be destroyed after stressing with 70 % of the value given in Table 2. Aft
40、er conditioning at a temperature of p25 3 C the spool shall not be destroyed after stressing with 50 % of the value given in Table 2. Spool type Mass Nominal g Tolerance % 100 125 160 200 90 150 250 450 2 2 2 2 Spool type Mass kg Energy N m 100 125 160 200 0,5 0,5 0,5 0,5 0,8 1,0 2,0 3,15EN 60264-2-
41、3:1994 BSI 5 May 2004 5 5.8 Deformation under load When stressed with the load specified in Table 3, the elongation shall not exceed the value given in Table 3. There are no requirements for other spools. Table 3 5.9 Flexibility test on flanges When stressed with the load specified in Table 4, the i
42、ncrease in distance between the flanges during and after stressing shall not exceed the value given in Table 4. There are no requirements for other spools. Table 4 Spool type Minimum tensile load kN Maximum elongation mm 100 125 160 200 5 6,3 8 10 1,0 1,0 1,6 2,0 Spool type Load kN Maximum increase
43、in distance between flanges mm During stressing After stressing 100 125 160 200 1,6 2,0 2,5 3,15 2,0 2,5 3,15 4,0 0,25 0,315 0,4 0,5EN 60264-2-3:1994 6 BSI 5 May 2004 Annex ZA (normative) Normative references to international publications with their corresponding European publications This European
44、Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications appl
45、y to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. NOTE When the international publication has been modified by CENELEC common modifications, indicated by (mod), the relevant EN/HD appli
46、es. IEC publication Date Title EN/HD Date 60264-2-1 1989 Packaging of winding wires Part 2: Cylindrical barrelled delivery spools Section 1: Basic dimensions EN 60264-2-1 1994 !60264-4-1 1997 Packaging of winding wires Part 4-1: Methods of test Delivery spools made from thermoplastic material “blank
47、BS EN 60264-2-3:1996 IEC 60264-2-3: 1990 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by R
48、oyal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding a
49、n inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standar
