1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 11148-4:2012Hand-held non-electric power tools Safety requirementsPart 4: Non-rotary percussive power toolsCopyright European Committee for Standardization Provided by
2、IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 11148-4:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 11148-4:2012. It supersedes BS EN ISO 11148-4:2010 which is withdrawn.The UK p
3、articipation in its preparation was entrusted to Technical Committee MCE/8/-/2, Hand-held, non-electric power tools - Safety.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of
4、a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013ISBN 978 0 580 78566 5 ICS 25.140.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published unde
5、r the authority of the Standards Policy and Strategy Committee on 31 January 2013.Amendments issued since publicationDate T e x t a f f e c t e dCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without licens
6、e from IHS-,-,-EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 11148-4 December 2012 ICS 25.140.10 Supersedes EN ISO 11148-4:2010English Version Hand-held non-electric power tools - Safety requirements - Part 4: Non-rotary percussive power tools (ISO 11148-4:2012) Machines portatives moteur
7、 non lectrique - Exigences de scurit - Partie 4: Machines portatives non rotatives percussion (ISO 11148-4:2012) Handgehaltene nicht elektrisch betriebene Maschinen - Sicherheitsanforderungen - Teil 4: Nicht drehende, schlagende Maschinen (ISO 11148-4:2012) This European Standard was approved by CEN
8、 on 17 December 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standard
9、s may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notif
10、ied to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Ice
11、land, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centr
12、e: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 11148-4:2012: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or ne
13、tworking permitted without license from IHS-,-,-BS EN ISO 11148-4:2012EN ISO 11148-4:2012 (E) 3 Foreword This document (EN ISO 11148-4:2012) has been prepared by Technical Committee ISO/TC 118“Compressors and pneumatic tools, machines and equipment“ in collaboration with Technical CommitteeCEN/TC 25
14、5 “Hand-held, non-electric power tools - Safety” the secretariat of which is held by SIS. This European Standard shall be given the status of a national standard, either by publication of an identicaltext or by endorsement, at the latest by June 2013, and conflicting national standards shall be with
15、drawn atthe latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patentrights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 11148-4:2010. This doc
16、ument has been prepared under a mandate given to CEN by the European Commission and theEuropean Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to th
17、e CEN/CENELEC Internal Regulations, the national standards organisations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, CzechRepublic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,Hung
18、ary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 11148-4:2012 has been approved by CEN as a EN ISO 11148-4:2012 without
19、anymodification. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 11148-4:2012EN ISO 11148-4:2012 (E) 4 Annex ZA (informative) Relationship between this European Standar
20、d and the EssentialRequirements of EU Directive 2006/42/EC This European Standard has been prepared under a mandate given to CEN by the European Commissionand the European Free Trade Association to provide a means of conforming to Essential Requirements of theNew Approach Directive 2006/42/EC on mac
21、hinery. Once this standard is cited in the Official Journal of the European Union under that Directive and has beenimplemented as a national standard in at least one Member State, compliance with the clauses of thisstandard confers, within the limits of the scope of this standard, a presumption of c
22、onformity with thecorresponding Essential Requirements of that Directive and associated EFTA regulations. WARNING Other requirements and other EU Directives may be applicable to the product(s) fallingwithin the scope of this standard. Copyright European Committee for Standardization Provided by IHS
23、under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 11148-4:2012ISO 11148-4:2012(E) ISO 2012 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope 12 Normative references . 23 Terms and definitions . 23.1 General definitio
24、ns 33.2 Definitions related to non-rotary percussive power tools . 44 Safety requirements and/or protective measures 44.1 General . 44.2 Mechanical safety 44.3 Thermal safety 54.4 Noise reduction 54.5 Vibration . 64.6 Materials and substances processed, used or exhausted . 64.7 Ergonomics and design
25、 of the handle . 64.8 Controls . 75 Verification 75.1 General conditions for tests . 75.2 Noise . 85.3 Vibration . 85.4 Unintentional start . 85.5 Power tool construction 85.6 Structure of verification of safety requirements . 96 Information for use . 96.1 Marking, signs and written warnings . 96.2
26、Instructions handbook .106.3 Operating instructions .156.4 Data .156.5 Maintenance instructions 16Annex A (informative) List of significant hazards 17Annex B (informative) Examples of non-rotary percussive power tools covered by this part of ISO 11148 .19Annex C (normative) Symbols for labels and si
27、gns23Annex D (normative) Additional safety requirements related to internal combustion engine power tools .24Bibliography .28Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN
28、 ISO 11148-4:2012ISO 11148-4:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body in
29、terested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechni
30、cal Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the t
31、echnical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IS
32、O shall not be held responsible for identifying any or all such patent rights.ISO 11148-4 was prepared by Technical Committee ISO/TC 118, Compressors and pneumatic tools, machines and equipment, Subcommittee SC 3, Pneumatic tools and machines.This second edition cancels and replaces the first editio
33、n (ISO 11148-4:2010), of which it constitutes a minor revision.ISO 11148 consists of the following parts, under the general title Hand-held non-electric power tools Safety requirements: Part 1: Assembly power tools for non-threaded mechanical fasteners Part 2: Cutting-off and crimping power tools Pa
34、rt 3: Drills and tappers Part 4: Non-rotary percussive power tools Part 5: Rotary percussive drills Part 6: Assembly power tools for threaded fasteners Part 7: Grinders Part 8: Sanders and polishers Part 9: Die grinders Part 10: Compression power tools Part 11: Nibblers and shears Part 12: Circular,
35、 oscillating and reciprocating sawsA part 13, dealing with fastener driving tools, is under preparation.iv ISO 2012 All rights reservedCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS
36、-,-,-BS EN ISO 11148-4:2012ISO 11148-4:2012(E)IntroductionThis document is a type C standard as stated in ISO 12100.The machinery concerned and the extent to which hazards, hazardous situations and events are covered are defined in the Scope of this part of ISO 11148.When provisions of this type C s
37、tandard are different from those that are stated in type A or B standards, the requirements of this type C standard take precedence over the requirements of other standards for machines that have been designed and built according to the requirements of this type C standard.ISO 11148 consists of a nu
38、mber of independent parts for individual types of hand-held, non-electric power tools.Certain elements of this part of ISO 11148 cover hand-held non-electric power tools, driven by internal combustion engines powered by gaseous or liquid fuel. In these parts, the safety aspects relating to internal
39、combustion engines are found in a normative annex.The parts are type C standards and refer to pertinent standards of types A and B where such standards are applicable. ISO 2012 All rights reserved vCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleN
40、o reproduction or networking permitted without license from IHS-,-,-BS EN ISO 11148-4:2012Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 11148-4:2012Hand-held non-elec
41、tric power tools Safety requirements Part 4: Non-rotary percussive power toolsIMPORTANT The electronic file of this document contains colours that are considered useful for the correct understanding of the document. Users should consider printing this document using a colour printer. ISO 3864-4 prov
42、ides colorimetric and photometric properties together with, as a guideline, references from colour order systems.1 ScopeThis part of ISO 11148 applies to hand-held non-electric power tools (hereinafter “non-rotary percussive power tools”) intended for chipping, riveting, breaking of concrete and asp
43、halt, ramming, etc. The non-rotary percussive power tool can be powered by compressed air, hydraulic fluid or internal combustion engines and is intended for use by one operator and supported by the operators hand or hands, with or without a suspension, e.g. a balancer.This part of ISO 11148 covers
44、breakers; bush hammers; chipping hammers; small chisels; engraving pens; needle scalers; pick hammers; pile drivers; portable pile drivers; punches; rammers; riveting hammers; scaling hammers; stone hammers; spades; tampers.NOTE 1 For examples of non-rotary percussive power tools, see Annex B.This p
45、art of ISO 11148 does not cover special requirements and modifications on non-rotary percussive power tools for the purpose of mounting in a fixture.INTERNATIONAL STANDARD ISO 11148-4:2012(E) ISO 2012 All rights reserved 1Copyright European Committee for Standardization Provided by IHS under license
46、 with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 11148-4:2012ISO 11148-4:2012(E)This part of ISO 11148 deals with all significant hazards, hazardous situations or hazardous events when the tools are used as intended and under conditions of misuse
47、which are reasonably foreseeable by the manufacturer, with the exception of the use of non-rotary percussive power tools in potentially explosive atmospheres.NOTE 2 EN 13463-1 gives requirements for non-electrical equipment for potentially explosive atmospheres.2 Normative referencesThe following do
48、cuments, in whole or in part, are normatively referenced this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 3857-3, Compressors, pneumatic tools and machines Vocabulary Part 3: Pneumatic tools and machinesISO 3864-2, Graphical symbols Safety colours and safety signs Part 2: Design principles for product safety labelsISO 5391, Pneumatic tools and machines Vo
