1、BRITISH STANDARD 24343-1:2012Resilient and laminate floor coverings Determination of indentation and residual indentation Part 1: Residual indentationICS 97.150nullnull nullnullnullnullnullnullnull nullnullnullnullnullnullnull nullnullnull nullnullnullnullnullnullnullnullnullnull nullnullnullnullnul
2、lnull nullnull nullnullnullnullnullnullnullnullnull nullnull nullnullnullnullnullnullnullnullnull nullnullnullBS EN ISO Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-National f
3、orewordThis British Standard is the UK implementation of EN ISO 24343-1:2012. It is identical to ISO 24343-1:2007. It supersedes BS EN 433:1994 and BS ISO 24343-1:2007,The UK participation in its preparation was entrusted to Technical Committee PRI/60, Resilient floor coverings.A list of organizatio
4、ns represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.BS
5、EN ISO 24343-1:2012This British Standard waspublished under the authorityof the Standards Policy andStrategy Committeeon 31 July 2007 The British Standards Institution 2012. Published by BSI Standards Limited 2012Amendments/corrigenda issued since publicationDate Comments 29 February 2012 This corri
6、gendum renumbers BS ISO 24343-1:2007 as BS EN ISO 24343-1:2012ISBN 978 0 580 75238 4which are withdrawn.Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPEAN STANDARD NORME EU
7、ROPENNE EUROPISCHE NORM EN ISO 24343-1 January 2012 ICS 97.150 Supersedes EN 433:1994English Version Resilient and laminate floor coverings - Determination of indentation and residual indentation - Part 1: Residual indentation (ISO 24343-1:2007) Revtements de sol rsilients et stratifis - Dterminatio
8、n du poinonnement et du poinonnement rmanent - Partie 1: Poinonnement rmanent (ISO 24343-1:2007) Elastische und Laminat-Bodenbelge - Bestimmung des Eindrucks und des Resteindrucks - Teil 1: Resteindruck (ISO 24343-1:2007) This European Standard was approved by CEN on 17 December 2011. CEN members ar
9、e bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to
10、the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Ce
11、ntre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, No
12、rway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in
13、 any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 24343-1:2012: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3 Foreword The text of ISO
14、24343-1:2007 has been prepared by Technical Committee ISO/TC 219 “Floor coverings” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 24343-1:2012 by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings” the secretariat of which i
15、s held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2012, and conflicting national standards shall be withdrawn at the latest by July 2012. Attention is drawn to the possibility th
16、at some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 433:1994. According to the CEN/CENELEC Internal Regulations, the national standards organizations
17、of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Ro
18、mania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 24343-1:2007 has been approved by CEN as a EN ISO 24343-1:2012 without any modification. BS EN ISO 24343-1:2012 EN ISO 24343-1:2012 (E)Copyright European Committee for Standardiza
19、tion Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1Resilient and laminate floor coverings Determination ofindentation and residual indentation Part 1: Residual indentation 1 Scope This part of ISO24343 describes a method for
20、 determining the residual indentation produced in a resilient orlaminate floor covering after the application and removal of a constant load. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply.2.1 residual indentation difference between the initial t
21、hickness and the thickness measured after removal of the load 2.2 thickness distance between two parallel plates where the floor covering is inserted under a specific load 3 Principle A test piece is subjected to a static loading, the thickness being measured before loading and after a recoveryperio
22、d. 4 Apparatus 4.1 Straight, steel cylindrical indenter, of diameter 11,30 mm 0,05 mm, with the edge of the flat baseslightly rounded. Area of the indenter: 100 mm2. 4.2 Rigid, horizontal platform, of a minimum diameter 35 mm.4.3 Device, by means of which a preliminary force of 3,00 N 0,03 N and a t
23、otal force of 500 N 0,5 N(pressure 5 MPa) can be smoothly applied. The frame shall not deform by more than 0,05 mm measured inthe direction of the axis under the maximum force. This deformation shall be taken into consideration whenmeasuring indentation. (See Figure 1.)4.4 Comparator, formeasuring t
24、he depth of indentation to 0,01 mm. BS EN ISO 24343-1:2012 EN ISO 24343-1:2012 (E)Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2 Dimensions in millimetres Key1 horizontal plat
25、form 5 comparator 2 test piece 6 dead weight3 annular weight 7 indenter 4 lever arm p pressure (5 MPa) h indentation depth Figure 1 Example of device to apply force on an indenter4.5 Apparatus for measuring the thickness of the test piece to the nearest 0,01mm . Diameter of thefoot: 6,00 mm 0,03 mm
26、(28,3 mm 2 ). Mass applied: 0,085 kg 0,003 kg (approximately 30 kPa). When the floor covering has one or more non-solid layers (e.g. foam), then a mass of 0,028 kg 0,001 kg(approximately10 kPa) shall be applied. 4.6 Stopwatch . 4.7 Annularweight, of approximate internal diameter 25 mm and a mass of
27、0,5 kg. BS EN ISO 24343-1:2012 EN ISO 24343-1:2012 (E)Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-35 Atmosphere for conditioning and testing Condition the test piece at a tem
28、perature of (23 2) C and a relative humidity of (50 5) % for a minimum of24 h. Maintain these conditions when carrying out the test. 6 Sampling and selection of specimen Take a representative sample from the available material. Take three test pieces each with dimensions of atleast 60 mm 60 mm cut f
29、rom a roll or different tiles or planks. 7 Test procedure 7.1 Mark the place of measurement and measure the initial thickness of the test piece, t 0 , at its centreto0,01 mm, using the appropriate massspecified in 4.5. 7.2 Place the test piece on the platform. Place the annular weight (4.7) and the
30、indenter (4.1) on the testpiece. 7.3 Within 5s, applythe preliminary force specified in 4.3 and adjust the comparator tozero, taking into consideration the deformation of the frame. Gently apply the total force specified in 4.3 and start the stopwatch within 2 s.7.4 Record the depth of indentation a
31、fter 150 min to 0,01 mm and remove the force and the test piece fromthe platform. This measurement is not required in the calculation of the results, but is required in a number of productspecifications. 7.5 After a further 150 min, measure the final thickness of the test piece, t 1 , at the marked
32、position, usingthe appropriate apparatus in 4.5.7.6 Repeat the test on the remaining test pieces. Calculate the mean value from the measurements takenand express the result to nearest 0,01 mm. 8 Calculation of resultsCalculate the residual indentation, t 0 t 1 , for each specimen. t 0 is the initial
33、 thickness, in millimetres,mm. t 1 is the final thickness, in millimetres, mm.9 Precision statementAn interlaboratory testwill be conducted to determine the precision of this method. BS EN ISO 24343-1:2012 EN ISO 24343-1:2012 (E)Copyright European Committee for Standardization Provided by IHS under
34、license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4 10 Test reportThe test report shall contain the following information:a) a statement that the tests were performed in accordance with this part of ISO 24343 (i.e. ISO 24343-1); b) complete identifica
35、tion of the product tested, including type, source, colour and manufacturers referencenumbers;c) previous history of the sample; d) the mean value for residual indentation; e) the mean value for the depth of indentation after 150 min; f) anydeviation from this part of ISO 24343, which mayhave affect
36、ed the results.BS EN ISO 24343-1:2012 EN ISO 24343-1:2012 (E)Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-5Bibliography1 EN 433, Resilient floor coverings Determination of res
37、idual indentation after stat ic loadingBS EN ISO 24343-1:2012 EN ISO 24343-1:2012 (E)Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BSI GroupHeadquarters 389 Chiswick High Road,
38、 London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standardsBSI - British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Roya
39、l Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inac
40、curacy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS whic
41、h ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy directly using
42、a debit/credit card from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of inform
43、ation on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (
44、0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: I
45、nformation regarding online access to British Standards via British Standards Online can be found at http:/ information about BSI is available on the BSI website at http:/ CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the interna
46、tional standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This d
47、oes not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager. Tel: +44 (0)20 8996 7070 Email: 24343-1:2012BS EN ISO Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
