1、BSI Standards PublicationBS ISO 6361-2:2014Wrought aluminium andaluminium alloys Sheets,strips and platesPart 2: Mechanical propertiesBS ISO 6361-2:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 6361-2:2014. The UK participation in its preparation was ent
2、rusted to TechnicalCommittee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct applicat
3、ion. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 84725 7 ICS 77.150.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Commit
4、tee on 30 September 2014.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e d ISO 2014Wrought aluminium and aluminium alloys Sheets, strips and plates Part 2: Mechanical propertiesAluminium et alliages daluminium corroys Tles, bandes et tles paisses Partie 2: Proprits mcaniques
5、INTERNATIONAL STANDARDISO 6361-2Fourth edition 2014-09-15Reference number ISO 6361-2:2014(E)BS ISO 6361-2:2014ISO 6361-2:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utiliz
6、ed otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright
7、officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 6361-2:2014ISO 6361-2:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Terms and definitions . 14
8、 Tensile testing . 15 Bend testing . 16 Mechanical properties 26.1 Tensile test 26.2 Bend test . 2Annex A (normative) Rules for rounding results obtained by inspection and testing 50Bibliography .51BS ISO 6361-2:2014ISO 6361-2:2014(E)ForewordISO (the International Organization for Standardization) i
9、s a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represe
10、nted on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop
11、 this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IE
12、C Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the
13、development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of
14、ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 79, Light m
15、etals and their alloys, Subcommittee SC 6, Wrought aluminium and aluminium alloys.This fourth edition cancels and replaces the third edition (ISO 6361-2:2011), which has been technically revised.ISO 6361 consists of the following parts, under the general title Wrought aluminium and aluminium alloys
16、Sheets, strips and plates: Part 1: Technical conditions for inspection and delivery Part 2: Mechanical properties Part 3: Strips: Tolerances on shape and dimensions Part 4: Sheets and plates: Tolerances on shape and dimensions Part 5: Chemical compositioniv ISO 2014 All rights reservedBS ISO 6361-2:
17、2014INTERNATIONAL STANDARD ISO 6361-2:2014(E)Wrought aluminium and aluminium alloys Sheets, strips and plates Part 2: Mechanical properties1 ScopeIn conjunction with ISO 6361-1, this part of ISO 6361 specifies the mechanical properties of wrought aluminium and aluminium alloy sheets, strips, and pla
18、tes for general engineering applications.It applies to flat-rolled products.The chemical composition of these materials is given in ISO 6361-5.The designations of aluminium and aluminium alloys and the temper designations used in this part of ISO 6361 are in accordance with ISO 2107.NOTE In certain
19、countries, for purposes of mechanical properties, the thickness limit can be lowered to 0,15 mm by agreement between the purchaser and the supplier, in the case of sheets and strips.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and ar
20、e indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6361-1, Wrought aluminium and aluminium alloys Sheets, strips and plates Part 1: Technical conditio
21、ns for inspection and delivery3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 6361-1 apply.4 Tensile testingFor the selection of the specimens and tensile testing, see ISO 6361-1.5 Bend testingFor the selection of the specimens and bend testing, see I
22、SO 6361-1. ISO 2014 All rights reserved 1BS ISO 6361-2:2014ISO 6361-2:2014(E)6 Mechanical properties6.1 Tensile testValues for mechanical properties of aluminium and aluminium alloys are given in Tables 1 to 63. For elongation, two different gauge lengths are used. The choice of the gauge length for
23、 elongation measurements (A or A50mm) is at the discretion of the producer, unless otherwise agreed.NOTE A is the percentage elongation on a gauge length of 565, So. A50mmis the percentage elongation on a gauge length of 50 mm.Test results shall be rounded in accordance with the rules given in Annex
24、 A.6.2 Bend testSheet, strip, and plate shall be capable of being bent cold through an angle of 180, as applicable, around a pin having a radius equal to k times the thickness, t, of the sheet, strip, or plate (for example 0,5t) without cracking. The values of the minimum bend radii for different al
25、loys, tempers, and thicknesses are given in Tables 1 to 63.NOTE The explanations of the numbered notes in Tables 1 to 63 are given after Table 63.Table 1 Aluminium 1050TemperTensile test Bend test2)Specified thick-ness mmTensile strength MPa0,2 % proof stress MPaElongation1)min. %Specified thickness
26、 mmRadiusover up to min. max. min. max. A50mmA over up toH1124,06,513,025,050,06,513,025,050,075,0858070656545453530201010162222O0,20,50,81,36,50,50,81,36,550,0606060606010010010010010020202015202530280,2 6,0 0tH12 or H223)0,20,30,50,81,32,90,30,50,81,32,912,08080808080801201201201201201206565652346
27、890,20,80,86,00t0,5tH14 or H243)0,20,30,50,81,32,90,30,50,81,32,912,09595959595951251251251251251257575751234560,20,80,86,00,5t1t2 ISO 2014 All rights reservedBS ISO 6361-2:2014ISO 6361-2:2014(E)TemperTensile test Bend test2)Specified thick-ness mmTensile strength MPa0,2 % proof stress MPaElongation
28、1)min. %Specified thickness mmRadiusover up to min. max. min. max. A50mmA over up toH16 or H263)0,20,50,81,30,50,81,34,0120120120120145145145145858512340,2 4,0 2tH180,20,50,81,30,50,81,33,01251251251251234Table 2 Aluminium 1050ATemperTensile test Bend test2)Specified thick-ness mmTensile strength MP
29、a0,2 % proof stress MPaElongation1)min. %Specified thickness mmRadiusover up to min. max. min. max. A50mmA over up toO0,20,51,53,06,012,50,51,53,06,012,525,065656565656595959595959520202020202020222629353232H140,20,51,53,00,51,53,06,0105105105105145145145145858585852345H240,20,51,53,00,51,53,06,0105
30、105105105145145145145757575753458H180,20,51,50,51,53,0140140140120120120120120120122Table 1 (continued) ISO 2014 All rights reserved 3BS ISO 6361-2:2014ISO 6361-2:2014(E)Table 3 Aluminium 1070, 1080, and 1085TemperTensile test Bend test2)Specified thick-ness mmTensile strength MPa0,2 % proof stress
31、MPaElongation1)min. %Specified thickness mmRadiusover up to min. max. min. max. A50mmA over up toH1124,06,513,025,050,06,513,025,050,075,0757060555535352520151315202525O0,20,30,50,81,313,00,30,50,81,313,050,05555555555559595959595951515151520253035300,2 6,0 0tH12 or H223)0,20,30,50,81,32,90,30,50,81
32、,32,912,07070707070701101101101101101105555552346890,2 6,0 0tH14 or H243)0,20,30,50,81,32,90,30,50,81,32,912,08585858585851201201201201201206565651234560,20,80,86,00,5t1tH16 or H263)0,20,50,81,30,50,81,34,0100100100100135135135135757512340,20,80,86,01t1,5tH180,20,50,81,30,50,81,33,012012012012012344
33、 ISO 2014 All rights reservedBS ISO 6361-2:2014ISO 6361-2:2014(E)Table 4 Aluminium 1070ATemperTensile test Bend test2)Specified thick-ness mmTensile strength MPa0,2 % proof stress MPaElongation1)min. %Specified thickness mmRadiusover up to min. max. min. max. A50mmA over up toO/H1110,20,51,53,06,012
34、,50,51,53,06,012,525,06060606060609090909090901515151515152325293235320,20,51,53,06,00,51,53,06,012,50t0t0t0,5t0,5tH1126,012,512,525,0707020 20 20H120,20,51,53,06,00,51,53,06,012,5808080808012012012012012055555555555679120,20,51,50,51,53,00,5t0,5t0,5tH140,20,51,53,06,00,51,53,06,012,5100100100100100
35、1401401401401407070707070445670,20,51,50,51,53,00,5t0,5t1tH160,20,51,50,51,54,01101101101501501509090902230,20,51,50,51,54,01t1t1tH180,20,51,50,51,53,0125125125105105105222H220,20,51,53,06,00,51,53,06,012,580808080801201201201201205050505050781012150,20,51,50,51,53,00,5t0,5t0,5tH240,20,51,53,06,00,5
36、1,53,06,012,510010010010010014014014014014060606060605679110,20,51,50,51,53,00,5t0,5t1tH260,20,51,50,51,54,0110110110150150150808080334 ISO 2014 All rights reserved 5BS ISO 6361-2:2014ISO 6361-2:2014(E)Table 5 Aluminium 1080ATemperTensile test Bend test2)Specified thick-ness mmTensile strength MPa0,
37、2 % proof stress MPaElongation1)min. %Specified thickness mmRadiusover up to min. max. min. max. A50mmA over up toO/H1110,20,51,53,06,00,51,53,06,012,560606060609090909090151515151526283135350,20,51,53,06,00,51,53,06,012,50t0t0t0,5t0,5tH1126,012,512,525,0707020 20H120,20,51,53,06,00,51,53,06,012,580
38、8080808012012012012012055555555555679120,20,51,50,51,53,00,5t0,5t0,5tH140,20,51,53,06,00,51,53,06,012,51001001001001001401401401401407070707070445670,20,51,50,51,53,00,5t0,5t1tH160,20,51,50,51,54,01101101101501501509090902230,20,51,50,51,54,01t1t1tH180,20,51,50,51,53,0125125125105105105222H220,20,51
39、,53,06,00,51,53,06,012,580808080801201201201201205050505050891113150,20,51,50,51,53,00,5t0,5t0,5tH240,20,51,53,06,00,51,53,06,012,510010010010010014014014014014060606060605679110,20,51,50,51,53,00,5t0,5t1tH260,20,51,50,51,54,01101101101501501508080803346 ISO 2014 All rights reservedBS ISO 6361-2:201
40、4ISO 6361-2:2014(E)Table 6 Aluminium 1100, 1100A, 1200, and 1230ATemperTensile test Bend test2)Specified thick-ness mmTensile strength MPa0,2 % proof stress MPaElongation1)min. %Specified thickness mmRadiusover up to min. max. min. max. A50mmA over up toH1124,06,513,050,06,513,050,075,09590858050503
41、525991420O0,20,50,81,36,50,50,81,36,575,0757575757510510510510510525252525251722223028250,2 6,0 0tH12 or H223)0,20,30,50,81,32,90,30,50,81,32,912,09595959595951251251251251251257575757575752346890,2 6,0 0,5tH14 or H243)0,20,30,50,81,32,90,30,50,81,32,912,012012012012012012014514514514514514595959595
42、95951234560,2 6,0 1tH16 or H263)0,20,50,81,30,50,81,34,013513513513516516516516511511511511512340,2 4,0 2tH180,20,50,81,30,50,81,33,01501501501501301301301301234Table 7 Alloy 2014TemperTensile test Bend test2)Specified thick-ness mmTensile strength MPa0,2 % proof stress MPaElongation1)min. %Specifie
43、d thickness mmRadiusover up to min. max. min. max. A50mmA over up toO4)0,40,513,00,513,025,022022022014014014016161090,41,62,91,62,96,00,5t1t1,5t ISO 2014 All rights reserved 7BS ISO 6361-2:2014ISO 6361-2:2014(E)TemperTensile test Bend test2)Specified thick-ness mmTensile strength MPa0,2 % proof str
44、ess MPaElongation1)min. %Specified thickness mmRadiusover up to min. max. min. max. A50mmA over up toT30,40,56,06,30,56,06,312,0395395395395245245240235141414130,40,51,62,90,51,62,96,01,5t2,5t3t3,5tT40,40,56,06,30,56,06,312,0395395400400240240250250141414140,40,51,62,90,51,62,96,01,5t2,5t3t3,5tT4515
45、)6,013,025,050,013,025,050,080,04004004003952502502502501414128107T426)0,40,50,525,04004002351414T60,40,51,06,06,30,51,06,06,312,0440440440450450390390390395395667770,40,51,62,90,51,62,96,03t3,5t4,5t5tT627)0,40,51,06,513,00,51,06,513,025,044044046046046039040041041066776T6516,013,025,050,060,080,013
46、,025,050,060,080,0100,04604604604504354054054054053903803807742265311Table 7 (continued)8 ISO 2014 All rights reservedBS ISO 6361-2:2014ISO 6361-2:2014(E)Table 8 Alloy 2014ATemperTensile test Bend test2)Specified thick-ness mmTensile strength MPa0,2 % proof stress MPaElongation1)min. %Specified thic
47、kness mmRadiusover up to min. max. min. max. A50mmA over up toO0,353,26,012,012,53,26,012,012,525,02202202202202201401401401401401616161612131212129T3 or T40,350,51,01,66,06,30,51,01,66,06,312,0395395395395395395240240240240240235141414141413T60,350,51,01,66,06,30,51,01,66,06,312,0440440440440440440
48、380380380390390390667777T4516,06,312,012,525,040,050,060,06,312,012,525,040,050,060,080,0395395400400400400395390240240250250250250250240141414141210877T6516,06,312,012,525,040,050,060,080,06,312,012,525,040,050,060,080,0100,04504504504604604504504354053953953954054053903903803507777653311 ISO 2014
49、All rights reserved 9BS ISO 6361-2:2014ISO 6361-2:2014(E)Table 9 Alloy 2017TemperTensile test Bend test2)Specified thick-ness mmTensile strength MPa0,2 % proof stress MPaElongation1)min. %Specified thickness mmRadiusover up to min. max. min. max. A50mmA over up toO4)0,40,50,525,021521511012120,41,62,91,62,96,00,5t1t1,5tT30,40,51,62,90,51,62,96,0375375375375215215215121517150,40,51,62,90,51,62,96,01,5t2,5t3t3,5tT3516,025,050,080,025,050,080
