DIN 1892-1-1981 Interlocking cylindrical cutters dimensions《交齿圆柱铣刀 尺寸》.pdf

相关资源

DIN EN 818-7-2008 Short link chain for lifting purposes - Safety - Part 7 Fine tolerance hoist chain Grade T (Types T DAT and DT)(includes Amendment A1 2008) Ge.pdf

DIN EN 1677-3-2008 Components for slings - Safety - Part 3 Forged steel self-locking hooks Grade 8(includes Amendment A1 2008) English version of DIN EN 1677-3 .pdf

DIN EN 1677-2-2008 Components for slings - Safety - Part 2 Forged steel lifting hooks with latch Grade 8(includes Amendment A1 2008) English version of DIN EN 1.pdf

DIN EN 1670-2007 Building hardware - Corrosion resistance - Requirements and test methods English version of DIN EN 1670 2007-06《建筑五金器具 耐腐蚀 要求和试验方法》.pdf

DIN EN 1656-2010 Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of bactericidal activity of chemical disinfectants and.pdf

DIN EN 1230-2-2018 Paper and board intended to come into contact with foodstuffs - Sensory analysis - Part 2 Off-flavour (taint) German version EN 1230-2 2009《用.pdf

DIN EN 1176-7-2008 Playground equipment and surfacing - Part 7 Guidance on installation inspection maintenance and operation English version of DIN EN 1176-7 20.pdf

DIN EN 1176-5-2008 Playground equipment and surfacing - Part 5 Additional specific safety requirements and test methods for carousels English version of DIN EN .pdf

DIN EN 1159-1-2007 Advanced technical ceramics - Ceramic composites - Thermophysical properties - Part 1 Determination of thermal expansion (includes Corrigendu.pdf

DIN EN 1093-4-2008 Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 4 Capture efficiency of an exhaust system - Tracer m.pdf

猜你喜欢

CSN ISO 8686-5-1994 Cranes Design principles for loads and load combinations Part 5 Overhead travelling and portal bridge cranes《起重机 装载及装载组合设计原则 第5部分：桥式起重机和门桥式起重机》.pdf

CSN ISO 8688-1-1993 Tool life testing in milling Part 1 Face milling《铣削刀具使用寿命测试 第1部分：面铣刀》.pdf

CSN ISO 8688-2-1993 Metal-cutting tools Tool life testing in milling Part 2 End milling《金属切割刀具 铣削刀具使用寿命测试 第2部分：端铣刀》.pdf

CSN ISO 8769-1994 Reference sources for the calibration of surface contamination monitors Beta-emiters (maximum energy greater than 0 15 MeV) and alpha-emitters《地面污染监测器校准用参考源β 发射器(.pdf

CSN ISO 8791-1-1993 Paper and board - Determination of roughness smoothness (air leak methods) - Part 1 General method《纸和纸板 粗糙度 平滑度测定（气漏方法） 第1部分：一般方法》.pdf

CSN ISO 8791-2-1994 Paper and board - Determination of roughness smoothness (air leak methods) - Part 2 Bendtsen method《纸和纸板 粗糙度 平滑度测定（气漏方法） 第2部分：本特森（Bendtsen）方法》.pdf

CSN ISO 8792-1993 Wire rope slings Safety criteria and inspection procedures for use《钢丝绳吊索 使用的安全标准和检查程序》.pdf

CSN ISO 8813-1994 Earth-moving machinery Lift capacity of pipelayers and wheeled tractors or loaders equipped with side boom《土方机械 配备侧起重臂的铺管机和轮式拖拉机或装载机的提升能力》.pdf

CSN ISO 8854-1992 Road vehicles Alternators with regulators Test methods and general requirements《道路车辆 带调节器的交流发电机 试验方法及一般要求》.pdf