DIN 38402-41-1984 German standard methods for the examination of water waste water and sludge general information (group A) inter-laboratory tests planning and organization (A 41)《.pdf

相关资源

DIN EN 818-7-2008 Short link chain for lifting purposes - Safety - Part 7 Fine tolerance hoist chain Grade T (Types T DAT and DT)(includes Amendment A1 2008) Ge.pdf

DIN EN 1677-3-2008 Components for slings - Safety - Part 3 Forged steel self-locking hooks Grade 8(includes Amendment A1 2008) English version of DIN EN 1677-3 .pdf

DIN EN 1677-2-2008 Components for slings - Safety - Part 2 Forged steel lifting hooks with latch Grade 8(includes Amendment A1 2008) English version of DIN EN 1.pdf

DIN EN 1670-2007 Building hardware - Corrosion resistance - Requirements and test methods English version of DIN EN 1670 2007-06《建筑五金器具 耐腐蚀 要求和试验方法》.pdf

DIN EN 1656-2010 Chemical disinfectants and antiseptics - Quantitative suspension test for the evaluation of bactericidal activity of chemical disinfectants and.pdf

DIN EN 1230-2-2018 Paper and board intended to come into contact with foodstuffs - Sensory analysis - Part 2 Off-flavour (taint) German version EN 1230-2 2009《用.pdf

DIN EN 1176-7-2008 Playground equipment and surfacing - Part 7 Guidance on installation inspection maintenance and operation English version of DIN EN 1176-7 20.pdf

DIN EN 1176-5-2008 Playground equipment and surfacing - Part 5 Additional specific safety requirements and test methods for carousels English version of DIN EN .pdf

DIN EN 1159-1-2007 Advanced technical ceramics - Ceramic composites - Thermophysical properties - Part 1 Determination of thermal expansion (includes Corrigendu.pdf

DIN EN 1093-4-2008 Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 4 Capture efficiency of an exhaust system - Tracer m.pdf

猜你喜欢

CSN 25 4036-1973 Screw gauges Minimum and maximum check plug for solid NOT GO screw ring gauge Metric screw thread diameter 1 mm to 100 mm《螺纹规 非穿过型实心螺纹环规的最小与最大检测插塞 直径为1mm 到 100 mm的.pdf

CSN 25 4039-1973 Screw gauges Wear check plug for solid or adjustable NOT GO screw ring gauge Metric screw thread diameter 1 mm to 100 mm《螺纹规 实心可调非通过式环螺钉规耐磨检查插塞 直径为1 mm 到 100 mm的公制.pdf

CSN 25 4045-1973 GO and NOT GO screw calliper gauge Metric thread of diameter over 3 mm up to 100 mm《穿过和非穿过型螺纹规 直径为3 mm到100 mm的公制螺纹》.pdf

CSN 25 4046-1973 Setting plug for GO and NOT GO screw calliper gauge Metric thread diameter over 3 mm up to 100 mm《穿过型及非穿过型螺丝两脚规底座插栓 直径3mm到100 mm的公制螺纹》.pdf

CSN 25 4047-1973 NOT GO screw calliper gauge Metric thread of diameter over 3 mm up to 100 mm《非穿过型螺纹规 直径3 mm到00 mm的公制螺纹》.pdf

CSN 25 4048-1985 Setting plug for NOT GO screw calliper gauge Metric thread of diameter over 3 mm up to 100 mm《非穿过型螺丝两脚规定位插塞 直径为3mm到100 mm的公制螺纹》.pdf

CSN 25 4050-1986 Screw gauges Limit screw plug gauges Cylindrical pipe thread diameter G 1 8 - G 3 1 2《螺纹规 止动螺钉插塞规 直径为G 1 8 到G3 1 2的圆柱形导管螺纹》.pdf

CSN 25 4055-1986 Screw gauges Solid GO screw ring gauges Cylindrical pipe thread diameter G 1 8 - G 3 1 2《螺纹规 穿过型实心环首螺钉规直径为1 8 - G 3 1 2的圆柱形导管螺纹》.pdf

CSN 25 4056-1986 Screw gauges Minimum and maximum check plugs for solid GO screw ring gauge Cylindrical pipe thread diameter G 1 8 - G 3 1 2《螺纹规 实心穿过型环首螺钉规最小及最大检测插栓 直径为1 8 - G 3 1 .pdf