1、July 2014Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 77
2、.140.50!%21“2159314www.din.deDDIN EN 10107Grain-oriented electrical steel strip and sheet delivered in the fullyprocessed state;English version EN 10107:2014,English translation of DIN EN 10107:2014-07Kornorientiertes Elektroband und -blech im schlussgeglhten Zustand;Englische Fassung EN 10107:2014,
3、Englische bersetzung von DIN EN 10107:2014-07Bandes et tles en acier lectrique grains orients livres ltat fini;Version anglaise EN 10107:2014,Traduction anglaise de DIN EN 10107:2014-07SupersedesDIN EN 10107:2005-10www.beuth.deIn case of doubt, the German-language original shall be considered author
4、itative.Document comprises 20 pages06.14 DIN EN 10107:2014-07 2 A comma is used as the decimal marker. National foreword This document (EN 10107:2014) has been prepared by Technical Committee ECISS/TC 108 “Steel sheet and strip for electrical applications” (Secretariat: DIN, Germany) of the European
5、 Committee for Iron and Steel Standardization (ECISS). The responsible German bodies involved in its preparation were the Normenausschuss Eisen und Stahl (Iron and Steel Standards Committee) and the DKE Deutsche Kommission Elektrotechnik Elektronik Informationstechnik im DIN und VDE (German Commissi
6、on for Electrical, Electronic and Information Technologies of DIN and VDE), Joint Working Committee NA 021-00-07 GA Elektroblech. Amendments This standard differs from DIN EN 10107:2005-10 as follows: a) normative references have been updated; b) Subclause 5.1 “Mandatory information”: the informatio
7、n relating to the minimum insulation coating resis-tance has been deleted; c) general requirements have been editorially revised; d) Subclause 6.3 “Delivery condition”: EN 10342 has been included as the reference standard; e) Tables 1, 2 and A.1: new steel grades have been added and all specificatio
8、ns have been brought in line with IEC 60404-8-7; f) Subclause 7.3.5 “Insulation coating resistance” has been technically revised; g) Subclauses 8.3 “Preparation of test specimens”, 8.3.1 “Magnetic properties”: the maximum length of Epstein strips has been increased to 320 mm; h) Subclause 8.3.3.4 “I
9、nsulation coating resistance”: EN 10282:2001 and IEC 60404-11:2013 have been added as reference standards for the inspection of the insulation coating resistance; i) the standard has been editorially revised. Previous editions DIN 46400-3: 1975-11, 1989-04 DIN EN 10107: 1996-02, 2005-10 EN 10107Marc
10、h 2014 ICS 77.140.50 Supersedes EN 10107:2005English Version Grain-oriented electrical steel strip and sheet delivered in the fully processed state Bandes et tles en acier lectrique grains orientslivres ltat finiKornorientiertes Elektroband und -blech im schlussgeglhten Zustand This European Standar
11、d was approved by CEN on 6 February 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning su
12、ch national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its ow
13、n language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
14、Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitati
15、on in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10107:2014 EEUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 10107:2014 (E) 2 Contents Page Foreword 3 1 Scope 4
16、 2 Normative references 4 3 Terms and definitions .5 4 Classification and designation .5 4.1 Classification 5 4.2 Designation 5 5 Information to be supplied by the purchaser .6 5.1 Mandatory information 6 5.2 Options .6 6 General requirements 7 6.1 Production process .7 6.2 Form of supply .7 6.3 Del
17、ivery condition 7 6.4 Surface condition.7 6.5 Suitability for cutting .7 7 Technical requirements 8 7.1 Magnetic properties .8 7.1.1 General 8 7.1.2 Magnetic polarization 8 7.1.3 Specific total loss 8 7.2 Geometric characteristics and tolerances . 10 7.2.1 Thickness 10 7.2.2 Width 11 7.2.3 Length 11
18、 7.2.4 Edge camber . 11 7.2.5 Flatness (wave factor) 12 7.2.6 Residual curvature 12 7.2.7 Burr height . 12 7.3 Technological characteristics . 12 7.3.1 Density . 12 7.3.2 Stacking factor 12 7.3.3 Number of bends 12 7.3.4 Internal stresses . 12 7.3.5 Insulation coating resistance 12 8 Inspection and
19、testing 12 8.1 General . 12 8.2 Sampling 13 8.3 Preparation of test specimens 13 8.3.1 Magnetic properties 13 8.3.2 Geometrical characteristics and tolerances 13 8.3.3 Technological characteristics . 14 8.4 Test methods . 14 8.4.1 General . 14 8.4.2 Magnetic properties 14 8.4.3 Geometrical character
20、istics and tolerances 15 8.4.4 Technological characteristics . 15 8.5 Retests . 16 9 Marking, labelling and packaging . 16 10 Complaints 16 Annex A (informative) Maximum specific total loss at 60 Hz and 1,7 T 17 Bibliography . 18 DIN EN 10107:2014-07EN 10107:2014 (E) 3 Foreword This document (EN 101
21、07:2014) has been prepared by Technical Committee ECISS/TC 108 “Steel sheet and strip for electrical applications”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the l
22、atest by September 2014 and conflicting national standards shall be withdrawn at the latest by September 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or
23、 all such patent rights. This document supersedes EN 10107:2005. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Est
24、onia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 10107:2014-07EN
25、 10107:2014 (E) 4 1 Scope This European Standard defines the steel grades of grain-oriented electrical strip and sheet in nominal thicknesses of 0,23 mm, 0,27 mm, 0,30 mm and 0,35 mm and specifies in particular, general requirements, magnetic properties, geometric characteristics and tolerances and
26、technological characteristics, as well as inspection procedures. This European Standard applies to Goss textured grain-oriented electrical strip and sheet supplied in the final annealed condition in sheets or coils, and intended for the construction of magnetic circuits. The materials are grouped in
27、to two classes: a) conventional grain oriented material; b) high permeability grain oriented material. They correspond to Clause C.22 of IEC 60404-1:2000. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its ap
28、plication. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10021, General technical delivery conditions for steel products EN 10027-1, Designation systems for steel Part 1: Steel names
29、EN 10027-2, Designation systems for steels Part 2: Numerical system EN 10204, Metallic products Types of inspection documents EN 10251, Magnetic materials Methods of determination of the geometrical characteristics of electrical steel sheet and strip EN 10280, Magnetic materials Methods of measureme
30、nt of the magnetic properties of electrical sheet and strip by means of a single sheet tester EN 10282:2001, Magnetic materials Method of test for the determination of surface insulation resistance of electrical sheet and strip EN 10342, Magnetic materials Classification of surface insulations of el
31、ectrical steel sheet, strip and laminations EN 60404-2, Magnetic materials Part 2: Methods of measurement of the magnetic properties of electrical steel sheet and strip by means of an Epstein frame (IEC 60404-2) EN 60404-11:2013, Magnetic materials Part 11: method of test for the determination of su
32、rface insulation resistance of magnetic sheet and strip EN 60404-13, Magnetic materials Part 13: Methods of measurement of density, resistivity and stacking factor of electrical steel sheet and strip (IEC 60404-13) EN ISO 7799:2000, Metallic materials Sheet and strip 3 mm thick or less Reverse bend
33、test (ISO 7799:1985) DIN EN 10107:2014-07EN 10107:2014 (E) 5 IEC 60050-121:1998, International Electrotechnical Vocabulary Chapter 121: Electromagnetism IEC 60050-221:1990, International Electrotechnical Vocabulary Chapter 221: Magnetic materials and components IEC 60404-3, Magnetic materials Part 3
34、: Methods of measurement of the magnetic properties of electrical steel strip and sheet by means of a single sheet tester 3 Terms and definitions For the purposes of this document, the terms and definitions of the principal terms relating to magnetic properties given in IEC 60050-121:1998 and IEC 60
35、050-221:1990 and the following apply. 3.1 edge camber greatest distance between a longitudinal edge of the sheet and the line joining the two extremities of the measured length of this edge 3.2 flatness property of a sheet or of a length of strip which is characterised by the wave factor i.e. by the
36、 relation of the height of the wave to its length 3.3 number of bends number of alternate bends possible before the appearance of the first crack in the base metal visible to the naked eye indicating the ductility of the material 3.4 internal stresses stresses which are characterised by a deviation
37、in relation to the line of cutting 4 Classification and designation 4.1 Classification The steel grades covered by this European Standard are classified according to the value of maximum specific total loss in watts per kilogram and according to the nominal thickness of the material (0,23 mm; 0,27 m
38、m; 0,30 mm; 0,35 mm). 4.2 Designation 4.2.1 For the steel grades covered by this European Standard, the steel names are allocated in accordance with EN 10027-1. The steel numbers are allocated in accordance with EN 10027-2. 4.2.2 The steel names comprise the following in the order given: a) capital
39、letter M for electrical steel; b) a number of one hundred times the specified value of maximum specific total loss at 1,7 T and 50 Hz, in watts per kilogram corresponding to the nominal product thickness; c) one hundred times the nominal thickness of the product, in millimetres; d) the characteristi
40、c letter: S for conventional grain oriented products; DIN EN 10107:2014-07EN 10107:2014 (E) 6 P for high permeability grain oriented products. EXAMPLE M140-30S for conventional grain oriented electrical steel strip or sheet with a maximum specific total loss of 1,40 W/kg at 1,7 T , 50 Hz and a nomin
41、al thickness of 0,30 mm, supplied in the fully processed state. 5 Information to be supplied by the purchaser 5.1 Mandatory information For material to comply adequately with the requirements of this standard, the purchaser shall include the following information in his enquiry or order: a) quantity
42、; b) type of product (strip or sheet); c) number of this European Standard (EN 10107); d) steel name or number (see 4.2.1); e) dimensions of sheets or strips required (including any limitations on the external diameter of a coil) (see 6.2 and 7.2.2); f) limitations on the mass of a bundle of sheets
43、or of a coil (see 6.2); g) residual curvature for coils (see 7.2.6); h) inspection procedure required including the nature of the related documents (see 8.1). 5.2 Options A number of options are specified in this standard and listed below. lf the purchaser does not indicate his wish to implement one
44、 of these options, the products shall be supplied in accordance with the basis specification of this standard (see 5.1). 1) permissibility of welds and its marking (see 6.2); 2) compatibility between fluid and coating (see 6.4); 3) plus tolerances for nominal width (see Table 3, footnote a); 4) requ
45、irement concerning residual curvature (see 7.2.6); 5) acceptance unit other than 3 t (see 8.1); 6) test temperature other than (23 5) C (see 8.4.1); 7) alternative method for determination of magnetic properties (see 8.4.2); 8) marking of the products (see Clause 9); 9) requirement concerning the mi
46、nimum insulation coating resistance (see 7.3.5). DIN EN 10107:2014-07EN 10107:2014 (E) 7 6 General requirements 6.1 Production process The production process of the steel and its chemical composition are left to the discretion of the manufacturer. 6.2 Form of supply The material is supplied in coils
47、 in the case of strip and bundles in the case of sheets. The mass of coils or bundles of sheets shall be agreed at the time of enquiry and order. The recommended value for the internal diameter of coils is approximately 508 mm. Strip shall be of constant width and wound in such a manner that the edg
48、es are superimposed in a regular manner and that the side faces of the coil are substantially flat. Coils shall be sufficiently tightly wound so that they do not collapse under their own weight. Strip may exhibit welds resulting from the removal of defective zones if agreed at the time of enquiry an
49、d order. If necessary the marking of welds may be agreed at the time of enquiry and order. For coils containing welds, each part of the strip shall be of the same grade. The edges of parts welded together shall not be so much out of alignment as to affect the further processing of the material. Sheets which make up each bundle shall be stacked so that the side faces are substantially flat and approximately perpendicular to the top face. 6.3 Del
