1、Beneficial comments recommendations, additions, deletions, clarifications, etc., and any data which may improvethis document should be addressed to: Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box3990, Columbus, OH 43213-1199, or telephone (614) 692-0562, or facsimile (FAX) (614) 69
2、3-1644.AMSC N/A FSC 5915DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.INCH-POUNDA-A-55167BSeptember 17, 2001SUPERSEDINGA-A-55167AApril 29, 1994COMMERCIAL ITEM DESCRIPTIONFILTER, RADIO FREQUENCY INTERFERENCEThe General Services Administration has authorized the use
3、of thiscommercial item description (CID) for all federal agencies as areplacement for Federal Specification W-F-2190/7.1. SCOPE. This CID covers the general requirements for radio frequency interference (RFI) suppression power linefilters. These filters consist of capacitors and inductors used in co
4、mbination with each other and are provided withresistors as a safety feature. Filters covered by this CID are intended for commercial/industrial applications andshould not be used in military systems needing stringent environmental and electrical requirements.2. CLASSIFICATION. This CID uses a class
5、ification system which is included in the Part Identification Number(PIN) as shown in the following example (see 7.1).AA55167 -01CID number Dash number3. SALIENT CHARACTERISTICS.3.1 Interface and physical dimensions. Filters supplied to this CID shall be as specified herein (see figures 1 and 2).3.2
6、. Voltage rating. The voltage rating shall be 120 V ac at 60 Hz; 250 V ac at 50 Hz.3.3 Operating frequency. The operating frequency shall be 50/60 Hz.3.4 Current rating. The current rating shall be as specified in table I.3.5 Operating ambient temperature range. The operating ambient temperature ran
7、ge shall be -10G01C to +40G01C atrated current.3.6 Maximum leakage current, line-to-ground. The maximum leakage current, line-to-ground, shall be 0.5 mA at120 V ac, 60 Hz; 1.0 mA at 250 V ac, 50 Hz.3.7 Hipot rating (1 minute). The hipot rating shall be 2,250 V dc line-to-ground; 1,450 V dc line-to-l
8、ine.3.8 Insertion loss. Insertion loss is given for line-to-ground in a 50-ohm circuit. Values shall be as specified in table I.3.9 Electrical schematic. The electrical schematic shall be as specified on figure 1.3.10 Marking. Filters supplied to this CID shall be marked with the manufacturers (MFRs
9、) standard commercialPIN.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55167B2TABLE I. Current rating and insertion loss.Minimum insertion loss (dB)Line-to-ground in 50 -ohm circuitFrequency (MHz)PINAA55167-Current rating.15.5 1 5 103001 1 A 30
10、656565656502 2 A 5446065656003 3 A 30656565656504 5 A 5446065656005 10 A 5446065656006 20 A 54460656560FIGURE 1. Electrical schematic.Case style AFIGURE 2. Case configuration and dimensions.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55167B3C
11、ase style BA(max)B(max)C(max)DG02.015/G02.38E(max)PINAA55167-Inch mm Inch mm Inch mm Inch mm Inch mmCasestyle01 3.35 85.1 1.81 46.0 1.16 29.5 2.375 60.33 2.78 70.6 A02 3.35 85.1 1.81 46.0 1 16 29.5 2.375 60.33 2.78 70.6 A03 3.85 97.8 2.07 52.6 1.16 29.5 2.938 74.63 3.35 85.1 A04 3.85 97.8 2.07 52.6
12、1.16 29.5 2.938 74.63 3.35 85.1 A05 3.85 97.8 2.07 52.6 1.53 38.9 2.938 74.63 3.35 85.1 A06 5.23 132.8 3.37 85.6 1.53 38.9 3.750 95.25 4.20 106.7 BNOTES:1. Dimensions are in inches.2. Metric equivalents are given for general information only.3. Fastons: (Five) .250 inch (6.35 mm).Holes: .07 inch (1.
13、8 mm) diameter.4. Mounting holes: (Two) .188 inch (4.78 mm) diameter.5. Mounting slots: (Four) .250 inch (6.35 mm) x .156 inch (3.96 mm).6. Metric equivalents are in parentheses.FIGURE 2. Case configuration and dimensions - Continued.Provided by IHSNot for ResaleNo reproduction or networking permitt
14、ed without license from IHS-,-,-A-A-55167B44. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to themaximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR).5. PRODUCT CONFORMANCE PROVISIONS5.1 Product confor
15、mance. The products provided shall meet the salient characteristics of this CID, conform to theproducers own drawings, specifications, standards, and quality assurance practices, and be the same productoffered for sale in the commercial market. The Government reserves the right to require proof of s
16、uch conformance.6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order.7. NOTES.7.1 PIN. The PIN should be used for Government purposes to buy commercial products to this CID. See section 2for PIN format example.7.2 Commercial and Government Entity (CAGE) cod
17、e. For ordering purposes, inventory control, and submission ofthese filters to DSCC under the Military Parts control Advisory Group (MPCAG) evaluation program, CAGE code58536 should be used.7.3 Source of documents. This section is not applicable to this CID.7.4 Ordering data. The contract or order s
18、hould specify the following:a. CID document number, revision, and CID PIN.b. Product conformance provisions.c. Packaging requirements.7.5 Commercial products. As part of the market analysis and research effort, this CID was coordinated with thefollowing manufacturers of commercial products. At the t
19、ime of CID preparation and coordination, thesemanufacturers were known to have commercial products that would meet the requirements of this CID. (NOTE:This information should not be considered as a list of approved manufacturers or be used to restrict procurement toonly the manufacturers shown.)MFRs
20、 CAGE MFRs name and address0S2B1 RME Filters, IncorporatedP. O. Box 83898 Route 101 AAmherst, NH 03031-083805245 CORCOM, Incorporated844 East Rockland RoadLibertyville, IL 6004864135 Filter Concepts, Incorporated2624 S. Rousselle StreetSanta Ana, CA 92707Provided by IHSNot for ResaleNo reproduction
21、or networking permitted without license from IHS-,-,-A-A-55167B57.6 Part number (PIN) supersession data. This CID supersedes the following manufacturers PINs as shown. Thisinformation is being provided to assist in reducing proliferation in the government inventory system.TABLE II. PIN supersession
22、data.MFRs CAGE0S2B1MFRs CAGE64135MFRs CAGE05245PINAA55167- MFRs Commercial PIN 1/01 RME-A-301-L - 1VR102 RME-A-302-L - 2VR103 RME-A-303-L SF3 3VR104 RME-A-305-L SF7 5VR105 RME-A-310-L SF10 10VR106 RME-A-320-L SF20 20VR11/ The manufacturers PIN shall not be used for procurement to the requirements of
23、 this CID.At the time of preparation of this CID, the aforementioned commercial products were reviewedand could be replaced by the CID PIN shown. For actual part marking requirements, see 3.11.7.7 Government users. To acquire information on obtaining these filters from the Government inventory syste
24、m,contact Defense Supply Center Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43216-5000,telephone (614) 692-0562 or facsimile (614) 693-1644.7.7.1 National stock number (NSN). The following is a list of NSNs assigned which correspond to this CID. The listis for information only and m
25、ay not be indicative of all possible NSNs associated with the CID. For up to dateinformation on assigned NSNs, please contact the aforementioned DSCC office (See 7.7).TABLE III. NSNs.PINAA55167-NSN01 -02 -03 5915-01-176-630804 -05 -06 -MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY:GSA - 7FXECustodians: Preparing Activity:Navy - EC DLA-CCProject 5915-0406Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
