DLA A-A-55558-1995 CONNECTOR RECEPTACLE ELECTRICAL UTILITY POWER 15 AMP 125 VOLT 50 60 HERTZ WITH COVER《50 60赫兹覆盖125伏特15安培公用电源电插座》.pdf

上传人:progressking105 文档编号:686940 上传时间:2018-12-30 格式:PDF 页数:4 大小:112.50KB
下载 相关 举报
DLA A-A-55558-1995 CONNECTOR RECEPTACLE ELECTRICAL UTILITY POWER 15 AMP 125 VOLT 50 60 HERTZ WITH COVER《50 60赫兹覆盖125伏特15安培公用电源电插座》.pdf_第1页
第1页 / 共4页
DLA A-A-55558-1995 CONNECTOR RECEPTACLE ELECTRICAL UTILITY POWER 15 AMP 125 VOLT 50 60 HERTZ WITH COVER《50 60赫兹覆盖125伏特15安培公用电源电插座》.pdf_第2页
第2页 / 共4页
DLA A-A-55558-1995 CONNECTOR RECEPTACLE ELECTRICAL UTILITY POWER 15 AMP 125 VOLT 50 60 HERTZ WITH COVER《50 60赫兹覆盖125伏特15安培公用电源电插座》.pdf_第3页
第3页 / 共4页
DLA A-A-55558-1995 CONNECTOR RECEPTACLE ELECTRICAL UTILITY POWER 15 AMP 125 VOLT 50 60 HERTZ WITH COVER《50 60赫兹覆盖125伏特15安培公用电源电插座》.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、A-A-55558 9999974 OLbb009 T47 pizzq A-A-55558 18 January 1995 COMMERCIAL ITEM DESCRIPTION CONNECTOR, RECEPTACLE. ELECTRICAL. UTILITY POWER. 15 AMP. 125 VOLT, 50/60 HERTZ WITH COVER The General Services Administration has authorized the use of this comercial item description (CID). for all federal ag

2、encies. 1. applications. system applications that do not have stringent environmental, electrical and mechanical requirements. 2. Number (PIN) (see 6.1). 3. SALIENT CHARACTERISTICS. 3.1 table I. SCOPE. This CID covers the general requirements for a power receptacle with a cover for wet location Part

3、s covered by this CID are intended for comnercial/industrial applications and military CLASSIFICATION. This CID uses a classification system which is included in the Part or Identification Confiquration and dimensions. Configuration and dimensions shall be as specified on figure 1 and 3.2 ReceDtacl

4、e configuration number 5-15R. General purpose. general grade. duplex. 2 pole. 3 wire. grounding. 15 ampere. 125 volt. 50/60 hertz, NEMA Color shall be brown. Receptacle shall be a qualified connector to W-C-596/12: PIN WC596/12-2. 3.3 W. Metallic or Non-metallic. two door. independent self closing,

5、for a standard mounting box. and for Cover plate shall be for wet location applications. with cover “open“: in accordance with UL 514A. for horizontal mounting. metallic type or in accordance with UL 514C for non-metallic type. 3.4 Item of SUDDY. necessary for installation, in one package. One item

6、of supply shall be one receptacle, one cover and any related hardware. ie. screws. gaskets. etc. Beneficial comnents. recommendations. additions. deletions clarifications. etc. and any other data which may improve this document should be sent to: Defense Electronics Supply Center. ATTN: DESC-ELDI. 1

7、507 Wilmington Pike, Dayton, OH 45444-5765. or telephone (513) 296-5391. or facsimile (FAX) (513) 296-8868. AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release: distribution is unlimited FSC 5935 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or netw

8、orking permitted without license from IHS-,-,-A-A-55558 = 9999974 OLbbOLO 769 W A-A- 55558 I I h , d,b, 1 4.5 REF (114) NOTES : 1. Dimensions are in inches. 2. Metric equivalents are given in parentheses for general information only Figure 1. Configuration and dimensions. 2 Provided by IHSNot for Re

9、saleNo reproduction or networking permitted without license from IHS-,-,-A-A-55558 9999974 OlbbOll bT5 W A- A- 55550 4. QUALITY ASSURANCE PROVISIONS 4.1 Contractor certification. The contractor shall certify and maintain objective quality evidence that the product offered meets the requirements of t

10、his CID. and that the product conforms to the producers own drawings. specifications. standards. quality assurances practices. and is the same as the product provided as a bid sample, if a bid sample is requested. The Government reserves the right to require proof of such conformance prior to the fi

11、rst delivery and thereafter as may be otherwise provided for under the provisions of the contract. 4.2 contractor to be placed on this document as a suggested source of supply. 5 PACKAGING. Certificate of comDliance. A certificate of compliance shall be submitted to DESC in order for the I 5.1 Prese

12、rvation. Dackaqinq. Dackinq. labelinq. and markinq. Preservation. packaging. labeling, and marking shall be as specified in the contract or purchase order. 6. the process of procuring the item. but is not mandatory. 6.1 government purposes and does not constitute a requirement for the contractor. NO

13、TES. This section contains relevant information which is useful to buyers, users and suppliers in Part Identification Number (PIN). The following part identification numbering procedure is for Y T- II Dash number CID number 6.2 Referenced documents. for request for proposal, form a part of this CID

14、to the extent specified herein. 6.2.1 Federal SDecification The following documents, of the issue in effect on date of invitation for bids W-C-596 - Connector. Electrical, Power, General Specification for W-C-596/12 - Connector, Receptacle, Electrir31. etc (Unless otherwise indicated. copies of fede

15、ral specifications are available from the Defense Printing Service Detachment Office. Building 40 (Customer Service), 700 Robbins Avenue. Philadelphia. PA 19111-5094.) 6 2.2 Underwriters Laboratories. Inc , (UL) Standard UL 514A - Box. Metallic Outlet. Standard for. UL 514C - Box. Non-metallic Outle

16、t. Flush Device Boxes and Covers. (Applicatiov for copies should be addressed to the Underwriters Laboratories. Inc . Publication Stock. 333 Pfingsten Road, Northbrook I 11 i noi s 60062. ) 6.2.3 National Electrical Manufacturers Association (NEMA) Pub1 ications : WD 6 - Wiring Devices - Dimensional

17、 Requirements. (Application for copies should be addressed to National Electrical Manufacturers Association. 2101 L Street. N.W., Suite 300. Washington. D C 20037.) 6.3 system. contact Defense Electronics Supply Center. AllN: 45444-5522. or telephone (513) 296-5009. Government users. To acquire info

18、rmation on obtaining these connectors from the Government inventory DESC-EON. 1507 Wilmington Pike, Dayton. OH I 3 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A - 55558 CID PIN PA55558- o1 6.4 Drderinq data. Acquisition documents should speci

19、fy the following: a. CID document number and revision and CID PIN. b. Quality assurance provisions. c. Packaging requirements. Vendor s Vendor * s NSN Cmrc i a 1 CAGE PIN number 5262 W5205WO 12497 5935-00-716- 3297 30501/2706 2H306 WR8lC 84258 5262 W/5205WO 9A329 6.5 Suqqested sources of SUDDY. Sugg

20、ested sources of supply are listed in table I. Additional sources will be added as they become available. TABLE I. Suggested sources of supply. Vendor CAGE Vendor name number and address 12497 The John A. Becker Co. 1341 East fourth St. Dayton. OH 45402-2235 Doy1 est own E 1 ec t r i c 3683 Easton R

21、d. Doylestown. PA 18901 901 Motor Pkwy. Hauppauge. NY 11788 Duellman Electric Div. 131 Wayne Ave. P.O.BOX 771 Dayton. OH 45401 2H306 84258 Avon Electrical Supplies. Inc. 9A329 Consolidated Electric Supply Co. CIVIL AGENCY COORDINATING ACTIVITY: GSA - 7fXE PREPARING ACTIVITY: DLA-ES (Project 59354527 ) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
  • DIN ISO 11727-2003 Pneumatic fluid power - Identification of ports and control mechanisms of control valves and other components (ISO 11727 1999)《气压传动 控制阀和其他元件的气口和控制机构的标识》.pdf DIN ISO 11727-2003 Pneumatic fluid power - Identification of ports and control mechanisms of control valves and other components (ISO 11727 1999)《气压传动 控制阀和其他元件的气口和控制机构的标识》.pdf
  • DIN ISO 1173-2009 Assembly tools for screws and nuts - Drive ends for hand- and machine-operated screwdriver bits and connecting parts - Dimensions torque testing (ISO 1173 2001) E.pdf DIN ISO 1173-2009 Assembly tools for screws and nuts - Drive ends for hand- and machine-operated screwdriver bits and connecting parts - Dimensions torque testing (ISO 1173 2001) E.pdf
  • DIN ISO 11745-2016 Brazing for aerospace applications - Qualification test for brazers and brazing operators - Brazing of metallic components (ISO 11745 2010 + Amd 1 2015)《航空航天应用钎焊.pdf DIN ISO 11745-2016 Brazing for aerospace applications - Qualification test for brazers and brazing operators - Brazing of metallic components (ISO 11745 2010 + Amd 1 2015)《航空航天应用钎焊.pdf
  • DIN ISO 1177-1989 Data communication representation of characters for serial data transmission identical with ISO 1177 1985《数据通讯 串口数据传输用字符的表示法 等同采用 ISO 1177 1985》.pdf DIN ISO 1177-1989 Data communication representation of characters for serial data transmission identical with ISO 1177 1985《数据通讯 串口数据传输用字符的表示法 等同采用 ISO 1177 1985》.pdf
  • DIN ISO 11798-2001 Information and documentation - Permanence and durability of writing printing and copying on paper - Requirements and test methods (ISO 11798 1999)《信息和文献 纸上书写、印刷.pdf DIN ISO 11798-2001 Information and documentation - Permanence and durability of writing printing and copying on paper - Requirements and test methods (ISO 11798 1999)《信息和文献 纸上书写、印刷.pdf
  • DIN ISO 11799-2017 Information and documentation - Document storage requirements for archive and library materials (ISO 11799 2015)《信息和文献工作 档案和图书馆资料的文献存储要求(ISO 11799-2015)》.pdf DIN ISO 11799-2017 Information and documentation - Document storage requirements for archive and library materials (ISO 11799 2015)《信息和文献工作 档案和图书馆资料的文献存储要求(ISO 11799-2015)》.pdf
  • DIN ISO 11800-2002 Information and documentation - Requirements for binding materials and methods used in the manufacture of books (ISO 11800 1998)《信息和文献 用于图书生产的装订材料和方法的要求》.pdf DIN ISO 11800-2002 Information and documentation - Requirements for binding materials and methods used in the manufacture of books (ISO 11800 1998)《信息和文献 用于图书生产的装订材料和方法的要求》.pdf
  • DIN ISO 11825-1999 Textile machinery and accessories - Latch-type needles for knitting machines - Coordination of shank widths and hook heights (ISO 11825 1995)《纺织机械和附件 编织机用舌型针 针杆宽.pdf DIN ISO 11825-1999 Textile machinery and accessories - Latch-type needles for knitting machines - Coordination of shank widths and hook heights (ISO 11825 1995)《纺织机械和附件 编织机用舌型针 针杆宽.pdf
  • DIN ISO 11843-1-2004 Capability of detection - Part 1 Terms and definitions (ISO 11843-1 1997 including Technical Corrigendum 1 2003)《检测能力 第1部分 术语和定义》.pdf DIN ISO 11843-1-2004 Capability of detection - Part 1 Terms and definitions (ISO 11843-1 1997 including Technical Corrigendum 1 2003)《检测能力 第1部分 术语和定义》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1