1、INCHPOUND AA59590/23B 23 March 2013 SUPERSEDING AA59590/23A 17 October 2007 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET HOLDER, ELECTRICAL CARD, WEDGE RETAINERS, 3 PIECE, SCREW ACTUATED DRIVE, .500 X .450 INCH BODY SIZE, WITH SCREW RETENTION The General Services Administration has authorized the
2、 use of this commercial item description for all federal agencies. The complete requirements for procuring electrical card holders described herein shall consist of this document and the latest issue in effect of AA59590. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). This commercial item descript
3、ion (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes). AA59590 CID number /23 Applicable CID specification sheet * Finish * Mounting * * Length (see table I) * Configuration (see table II) Ex
4、ample: AA59590/23EV58D is the PIN for a nickel plated, 5.8 inches (147 mm) long card holder with a flat washer, lockwasher, and screw self-locking element. The card holder also features two tapped mounting holes for use with 2-56 UNC 2A fasteners. SALIENT CHARACTERISTICS. Interface and physical dime
5、nsions. The card holders supplied to this CID specification sheet shall be as specified herein (see figures 1, 2, 3, 4, and table I) and meet the general requirements of CID AA59590. Material. Unless otherwise specified herein, the card holder materials shall be as specified in AA59590. Performance.
6、 Card holders shall hold the circuit card assembly it is attached to firmly in its installed position and prevent loosening or movement as a result of shock and vibration. The card holder shall also provide a thermal transfer path from the circuit card assembly to the cold plate or heat sink surface
7、s. Screw retention (see figure 2). The screw retention feature is intended to prevent the unintentional disassembly of the card holder. The self-locking nut used for the screw retention feature shall be fabricated of a corrosion resistant material. Actuating screw hex drive socket. The dimension for
8、 hex drive socket shall be as specified on figure 1. Cold plate dimensions. The recommend cold plate slot width to accommodate the circuit card assembly with attached card holder is .525 inch (13.3 mm) plus the thickness of the printed board of the circuit card assembly (see AA59590). AMSC N/A FSC 5
9、998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/23B 2 Inches mm Inches mm Inches mm Inches mm Inches mm .156 .19 3.96 4.8 .20 .25 5.1 6.4 .30 .31 7.62 7.9 .460 .500 11.68 12.70 .600 .70 15.24 17.8 NOTES: 1. Dimensions are in inches. Milli
10、meters are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. 3. The tolerance for the mounting hole spacing is .005 inches (0.13 mm). 4. The across flats dimension for hex driv
11、e socket shall be .156 inch (3.96 mm) for mounting options “J“, “N“, “T“, and “V“. The across flats dimension for hex drive socket shall be a metric dimension of 3.0 mm (.118 inch) across flats for mounting option “G“. FIGURE 1. Relaxed and expanded dimensions, basic configuration. Provided by IHSNo
12、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/23B 3 Nominal installation torque. When card holders are used in cold plate applications, the nominal installation torque of each card holder shall be as follows: 31 inch-pounds (3.5 N-m) for assemblies using no
13、 options or option “W“ and from 34 to 36 inch-pounds (3.8 to 4.1 N-m) for assemblies using options “D“ or “E“. Screw retention (locknut). The screw retention feature is intended to prevent unintentional disassembly of the card holder shall be as specified in figure 2. The locknut shall be fabricated
14、 of a corrosion resistant material. FIGURE 2. Screw retaining self-locking nut details. Finish. The finish materials shall be as specified in AA59590. The wedge body finishes available for this CID specification sheet are as follows: “B“ (black anodize), “C“ (gold chemical film), “E“ (electroless ni
15、ckel), “H“ (hard black anodize), or “R“ (clear chemical film). Mounting. The mounting designators shall be as specified in AA59590. Except when using mounting option “N“, two mounting holes are required on the card holders. The mounting options available for this CID specification sheet are as follo
16、ws: “J“ (rivet mounting holes), “N“ (no mounting holes), “T“ (tapped 0-80 UNF 2B holes), “V“ (tapped 2-56 UNC 2B holes), or “G“ (tapped M2.5 x.45 metric holes). See figure 1 and table I for mounting hole spacing requirements. Card holders using mounting option “J“ may be shipped unassembled. Rivet m
17、ounting holes. The holes used for rivet mounting shall be .136 inch (3.45 mm) diameter, countersunk 100 degrees by .190/.200 inch (4.83/5.08 mm) diameter through holes with an access/clearance counterbore of .190/.200 inch (4.83/5.08 mm) diameter by .390 inch (9.91 mm) deep. Rivets. This card holder
18、 uses rivet style B as specified in AA59590 when rivet mounting is used. Length, expanded, and relaxed dimensions. The length designator shall be as specified in AA59590 and the lengths available for this CID specification sheet are listed in table I. The length, expanded, and relaxed dimensions sha
19、ll be as specified on figure 1. TABLE I. Assembly dimensions (see figure 1). PIN length designator Dimension “LENGTH“ .02 (0.5 mm) Dimension “B“ .03 (0.8 mm) Dimension “M“ .005 (0.13 mm) 28 2.8 (71 mm) 2.30 (58.4 mm) .90 (22.9 mm) 38 3.8 (97 mm) 3.30 (83.8 mm) 1.90 (48.3 mm) 48 4.8 (122 mm) 4.30 (10
20、9.2 mm) 2.90 (73.7 mm) 58 5.8 (147 mm) 5.30 (134.6 mm) 3.90 (99.1 mm) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/23B 4 Configuration. The configuration of a card holder shall be as specified in table II. The details of a particular confi
21、guration consist of those on figures 1 and 2, and may include those on figures 3 and 4. The correct PIN configuration identifier for each option is listed in table II. Card holders not requiring the options described by table II shall leave the configuration position in the PIN blank. TABLE II. Conf
22、iguration. Configuration designator Applicable figures Hardware added to basic configuration 1 and 2 No changes from basic configuration W 1, 2 and 3 Lockwasher and flat washer E 1, 2 and 4 Screw self-locking element D 1, 2, 3 and 4 Lockwasher, flat washer, and screw self-locking element Lockwasher
23、and flat washer (see figure 3). The use of a lockwasher and flat washer located under the screw head will provide for additional resistance to loosening of the card holder assembly from shock and vibration. Card holders requiring a lockwasher and flat washer option shall include a suffix “W“ in the
24、PIN (see classification and notes herein). FIGURE 3. Lockwasher and flat washer details. Screw self-locking element (see figure 4). The use of a self-locking element on the screw will provide a prevailing-torque for increased resistance to loosening of the card holder assembly from shock and vibrati
25、on. The screw self-locking element shall be as specified in AA59590. Card holders requiring a screw self-locking element shall include configuration identifier “E“ in the PIN (see classification and notes herein). FIGURE 4. Screw self-locking element details. Provided by IHSNot for ResaleNo reproduc
26、tion or networking permitted without license from IHS-,-,-AA59590/23B 5 Lockwasher, flat washer, and screw self-locking element. Card holders requiring a lockwasher, flat washer, and screw self-locking element option shall include a suffix “D“ in the PIN (see classification and notes herein). NOTES.
27、 PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of documents. Commercial Item Description. AA59590 Holder, Electrical Card, Wedge Retainers, 3 Piece, Screw Actuated Drive, G
28、eneral Requirements For. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch or https:/assist.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data shall be as specified in
29、AA59590. Commercial products. As part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commerci
30、al products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact
31、 information 61081 Calmark A Division of Pentair Electronic Packaging 7328 Trade Street San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 American Circuit Card Retainers, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 92806
32、1231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: http:/ Part number supersession data. These CID specification sheet PINs supersedes the following manufacturers part numbers as shown in table III. The CID PINs listed in table III are only for length designator “28“. See table IV
33、for CID PIN construction using other available lengths for this specification sheet. This information is being provided to assist in reducing proliferation in the Government inventory system. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/23
34、B 6 TABLE III. Commercial part number supersession data. PIN designator AA59590/23 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 BJ28 A255CR2.80HR 3500BA2.80HR BN28 A255CR2.80R 3500BA2.80R BT28 A255CR2.80T0R 3500BA2.80T0R BV28 A255CR2.80T2R 3500BA2.80T2R BG28 MA255CR2.80T
35、M2.5R 3500MBA2.80TM2.5R BJ28W WA255CR2.80HR 3500WBA2.80HR BN28W WA255CR2.80R 3500WBA2.80R BT28W WA255CR2.80T0R 3500WBA2.80T0R BV28W WA255CR2.80T2R 3500WBA2.80T2R BG28W MWA255CR2.80TM2.5R 3500MWBA2.80TM2.5R BJ28E A255CR2.80HLR 3500BA2.80HLR BN28E A255CR2.80LR 3500BA2.80LR BT28E A255CR2.80T0LR 3500BA2
36、.80T0LR BV28E A255CR2.80T2LR 3500BA2.80T2LR BG28E MA255CR2.80TM2.5LR 3500MBA2.80TM2.5LR BJ28D WA255CR2.80HLR 3500WBA2.80HLR BN28D WA255CR2.80LR 3500WBA2.80LR BT28D WA255CR2.80T0LR 3500WBA2.80T0LR BV28D WA255CR2.80T2LR 3500WBA2.80T2LR BG28D MWA255CR2.80TM2.5LR 3500MWBA2.80TM2.5LR CJ28 255CR2.80HR 350
37、0CG2.80HR CN28 255CR2.80R 3500CG2.80R CT28 255CR2.80T0R 3500CG2.80T0R CV28 255CR2.80T2R 3500CG2.80T2R CG28 M255CR2.80TM2.5R 3500MCG2.80TM2.5R CJ28W W255CR2.80HR 3500WCG2.80HR CN28W W255CR2.80R 3500WCG2.80R CT28W W255CR2.80T0R 3500WCG2.80T0R CV28W W255CR2.80T2R 3500WCG2.80T2R CG28W MW255CR2.80TM2.5R
38、3500MWCG2.80TM2.5R See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/23B 7 TABLE III. Commercial part number supersession data. PIN designator AA59590/23 Vendor similar designator or type part number 1/ 2/ CAGE 61
39、081 CAGE 5BG68 CJ28E 255CR2.80HLR 3500CG2.80HLR CN28E 255CR2.80LR 3500CG2.80LR CT28E 255CR2.80T0LR 3500CG2.80T0LR CV28E 255CR2.80T2LR 3500CG2.80T2LR CG28E M255CR2.80TM2.5LR 3500MCG2.80TM2.5LR CJ28D W255CR2.80HLR 3500WCG2.80HLR CN28D W255CR2.80LR 3500WCG2.80LR CT28D W255CR2.80T0LR 3500WCG2.80T0LR CV2
40、8D W255CR2.80T2LR 3500WCG2.80T2LR CG28D MW255CR2.80TM2.5LR 3500MWCG2.80TM2.5LR EJ28 EN255CR2.80HR 3500EN2.80HR EN28 EN255CR2.80R 3500EN2.80R ET28 EN255CR2.80T0R 3500EN2.80T0R EV28 EN255CR2.80T2R 3500EN2.80T2R EG28 MEN255CR2.80TM2.5LR 3500MEN2.80TM2.5R EJ28W WEN255CR2.80HR 3500WEN2.80HR EN28W WEN255C
41、R2.80R 3500WEN2.80R ET28W WEN255CR2.80T0R 3500WEN2.80T0R EV28W WEN255CR2.80T2R 3500WEN2.80T2R EG28W MWEN255CR2.80TM2.5R 3500MWEN2.80TM2.5R EJ28E EN255CR2.80HLR 3500EN2.80HLR EN28E EN255CR2.80LR 3500EN2.80LR ET28E EN255CR2.80T0LR 3500EN2.80T0LR EV28E EN255CR2.80T2LR 3500EN2.80T2LR EG28E MEN255CR2.80T
42、M2.5LR 3500MEN2.80TM2.5LR EJ28D WEN255CR2.80HLR 3500WEN2.80HLR EN28D WEN255CR2.80LR 3500WEN2.80LR ET28D WEN255CR2.80T0LR 3500WEN2.80T0LR EV28D WEN255CR2.80T2LR 3500WEN2.80T2LR EG28D MWEN255CR2.80TM2.5LR 3500MWEN2.80TM2.5LR See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction o
43、r networking permitted without license from IHS-,-,-AA59590/23B 8 TABLE III. Commercial part number supersession data. PIN designator AA59590/23 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 HJ28 HA255CR2.80HR 3500BH2.80HR HN28 HA255CR2.80R 3500BH2.80R HT28 HA255CR2.80T0R
44、 3500BH2.80T0R HV28 HA255CR2.80T2R 3500BH2.80T2R HG28 MHA255CR2.80TM2.5LR 3500MBH2.80TM2.5R HJ28W WHA255CR2.80HR 3500WBH2.80HR HN28W WHA255CR2.80R 3500WBH2.80R HT28W WHA255CR2.80T0R 3500WBH2.80T0R HV28W WHA255CR2.80T2R 3500WBH2.80T2R HG28W MWHA255CR2.80TM2.5LR 3500MWBH2.80TM2.5R HJ28E HA255CR2.80HLR
45、 3500BH2.80HLR HN28E HA255CR2.80LR 3500BH2.80LR HT28E HA255CR2.80T0LR 3500BH2.80T0LR HV28E HA255CR2.80T2LR 3500BH2.80T2LR HG28E MHA255CR2.80TM2.5LR 3500MBH2.80TM2.5LR HJ28D WHA255CR2.80HLR 3500WBH2.80HLR HN28D WHA255CR2.80LR 3500WBH2.80LR HT28D WHA255CR2.80T0LR 3500WBH2.80T0LR HV28D WHA255CR2.80T2LR
46、 3500WBH2.80T2LR HG28D MWHA255CR2.80TM2.5LR 3500MWBH2.80TM2.5LR RJ28 R255CR2.80HR 3500CC2.80HR RN28 R255CR2.80R 3500CC2.80R RT28 R255CR2.80T0R 3500CC2.80T0R RV28 R255CR2.80T2R 3500CC2.80T2R RG28 MR255CR2.80TM2.5R 3500MCC2.80TM2.5R RJ28W WR255CR2.80HR 3500WCC2.80HR RN28W WR255CR2.80R 3500WCC2.80R RT2
47、8W WR255CR2.80T0R 3500WCC2.80T0R RV28W WR255CR2.80T2R 3500WCC2.80T2R RG28W MWR255CR2.80TM2.5R 3500MWCC2.80TM2.5R See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59590/23B 9 TABLE III. Commercial part number supersessi
48、on data. PIN designator AA59590/23 Vendor similar designator or type part number 1/ 2/ CAGE 61081 CAGE 5BG68 RJ28E WR255CR2.80HR 3500WCC2.80HR RN28E WR255CR2.80R 3500WCC2.80R RT28E WR255CR2.80T0R 3500WCC2.80T0R RV28E WR255CR2.80T2R 3500WCC2.80T2R RG28E MWR255CR2.80TM2.5R 3500MWCC2.80TM2.5R RJ28D WR255CR2.80HLR 3500WCC2.80HLR RN28D WR255CR2.80LR
