1、INCHPOUND AA59832/2A 2 February 2011 SUPERSEDING AA59832/2 2 October 2009 COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET EXTRACTOR, ELECTRICAL CARD, METAL, NON LOCKING, SINGLE ACTION, FOR “U” CHANNEL ACTUATING SURFACES, FOR .032, .063, .094, AND .125 INCH THICK CIRCUIT CARD ASSEMBLIES The General S
2、ervices Administration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring extractors described herein shall consist of this document and the latest issue in effect of AA59832. CLASSIFICATION/PART IDENTIFICATION NUMBER (PIN). T
3、his commercial item description (CID) specification sheet uses a classification system which is included in the Part Identification Number (PIN) as shown in the following example (see notes herein). AA59832 CID number /02 Applicable CID sheet * Configuration (see table I) * Slot width (see table I)
4、1 Material * Finish * Color Example: AA59832/02MS1AB is the PIN for a medium length aluminum extractor designed for mounting on a circuit card assembly with a printed board thickness of .063 inch (1.60 mm) in width. The corrosion protection finish applied to the extractor is black anodize. SALIENT C
5、HARACTERISTICS. Performance. Extractors shall be capable of injecting and removing the circuit card assembly from its installed position. Interface and physical dimensions. The extractors supplied to this CID specification sheet shall be as specified herein and meet the general requirements specifie
6、d in CID AA59832. Configuration. The configuration of a extractor shall be as specified in table I. The details of a particular configuration consist of those on figures 1, 2, and 3. Slot width. The available slot widths needed to accommodate various printed board thicknesses for the extractors cove
7、red by this CID specification sheet are specified in table I. Material. The extractor material shall be aluminum alloy 6061, temper T6 as specified in AA59832. The material designator shall be a “1“ as specified in AA59832. Finish. The finish designator shall be as specified in AA59832. The finishes
8、 available for this CID specification sheet are as follows: “A“ (anodize) or “L“ (low resistance chemical film). AMSC N/A FSC 5998 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/2A 2 Color. The color designator shall be as specified in AA598
9、32. The colors available for this CID specification sheet are as follows: “B“ (black) or “R“ (red) for anodize finishes and “C“ (clear) or “G“ (gold) for low resistance chemical film. Roll pin. A stainless steel roll pin is furnished with each extractor. The roll pin is .09375 inch (2.38 mm) diamete
10、r by .3125 inch (7.9 mm) long. TABLE I. Configurations and dimensions. 1/ Configuration Slot width designator Slot width dimension “W“ 2/ Inch (mm) Accommodates printed board thickness Inch (mm) Figure S F .048 (1.22) .032 (0.79) 1 S S .080 (2.03) .063 (1.6) S T .110 (2.79) .094 (2.4) S E .140 (3.56
11、) .125 (3.2) M F .048 (1.22) .032 (0.79) 2 M S .080 (2.03) .063 (1.6) M T .110 (2.79) .094 (2.4) M E .140 (3.56) .125 (3.2) L F .048 (1.22) .032 (0.79) 3 L S .080 (2.03) .063 (1.6) L T .110 (2.79) .094 (2.4) L E .140 (3.56) .125 (3.2) 1/ Dimensions are in inches. Millimeters, in parenthesis, are giv
12、en for general information only. 2/ Tolerance is +.010, .000 inch (+0.25, 0.000 mm). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/2A 3 Inches mm Inches mm Inches mm Inches mm .003 .015 .062 0.07 0.38 1.57 .093 .120 .156 2.36 3.05 3.96 .182
13、 .290 .475 4.62 7.37 12.07 .50 1.50 12.7 38.1 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. FIGURE 1. Configu
14、ration S dimensions (approximate mechanical advantage of 3.3:1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/2A 4 Inches mm Inches mm Inches mm Inches mm .003 .015 .060 0.07 0.38 1.52 .093 .120 .156 2.36 3.05 3.96 .182 .290 .475 4.62 7.37
15、 12.07 .50 2.00 12.7 50.8 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. FIGURE 2. Configuration M dimensions
16、(approximate mechanical advantage of 4.5:1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/2A 5 Inches mm Inches mm Inches mm Inches mm .003 .015 .060 0.07 0.38 1.52 .093 .120 .156 2.36 3.05 3.96 .182 .290 .475 4.62 7.37 12.07 .50 3.50 12.7
17、 88.9 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. FIGURE 3. Configuration L dimensions (approximate mechani
18、cal advantage of 8:1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/2A 6 APPLICATION DATA. Card cage actuating surface. The nominal position of circuit card assembly edge to the “U“ channel edge when seated in the connector is shown on fig
19、ure 4. The extractor will allow .05 inch (1.3 mm) over travel for tolerance take-up. The circuit card assembly is ejected from its installed position by lever action of the ejector against the “U“ channel of the card cage. A single ejector is recommended for circuit card assemblies up to 5 inches (1
20、27 mm) in width. For circuit card assemblies over 5 inches (127 mm) in width, or when using an electrical connector(s) with more than 100 contacts, two ejectors mounted on each circuit card assembly is recommended. Inches mm Inches mm Inches mm Inches mm .015 0.38 .05 .06 1.3 1.5 .24 .285 6.1 7.24 .
21、50 1.50 12.7 38.1 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two place decimals and .010 inch (0.25 mm) for three place decimals. FIGURE 4. Circuit card assembly to card cage
22、dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/2A 7 Circuit card assembly printed board. The circuit card assembly should be designed so that electronic components in the area around the ejector mounting hole have sufficient clea
23、rance for ejector rotation as shown on figure 5. Inches mm Inches mm Inches mm Inches mm .109 2.77 .250 6.35 .36 9.14 .73 18.5 NOTES: 1. Dimensions are in inches. Millimeter equivalents are given for general information only. 2. Unless otherwise specified, tolerances are .02 inch (0.51 mm) for two p
24、lace decimals and .010 inch (0.25 mm) for three place decimals. FIGURE 5. Printed board clearance zone and mounting hole dimensions. NOTES. PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format ex
25、ample. Source of documents. Commercial Item Description AA59832 Extractor, Electrical Card, Metal, General Requirements For. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700
26、Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) Ordering data. Ordering data is as specified in AA59832. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/2A 8 Commercial products. As part of the market analysis and research effort, t
27、his CID specification sheet was coordinated with the following manufacturers of commercial products. At the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE
28、: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) Manufacturer CAGE Manufacturer name and address Manufacturer contact information 61081 Calmark A Division of Pentair Technical Products 7328 Trade Stre
29、et San Diego, CA 921213410 Telephone: (858) 7402400 Toll Free: (800) 8547086 Facsimile: (858) 7402430 Electronic mail: URL: 5BG68 Card Locks Unlimited, Inc. 2310 E. Orangethorpe Avenue Anaheim, CA 928061231 Telephone: (714) 7386194 Facsimile: (714) 4460119 E-mail: URL: Part number (P/N )superses
30、sion data. These CID specification sheet PINs supersede the following manufacturers P/Ns as shown in table II. This information is being provided to assist in reducing proliferation in the Government inventory system. TABLE II. Commercial P/N supersession data. PIN designator AA59832/02 Vendor simil
31、ar designator or type part number 1/ CAGE 5BG68 Vendor similar designator or type part number 1/ CAGE 61081 SF1AB 17511BA SS1AB 17512BA 10751 ST1AB 17513BA 107513 SE1AB 17514BA 107514 SF1LC 17511CC SS1LC 17512CC C10751 ST1LC 17513CC C107513 SE1LC 17514CC C107514 SF1LG 17511CG SS1LG 17512CG ST1LG 175
32、13CG SE1LG 17514CG SF1AR 17511RA SS1AR 17512RA ST1AR 17513RA SE1AR 17514RA See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/2A 9 TABLE II. Commercial P/N supersession data Continued. PIN designator AA59832/02 Vend
33、or similar designator or type part number 1/ CAGE 5BG68 Vendor similar designator or type part number 1/ CAGE 61081 MF1AB 17501BA MS1AB 17502BA 10750 MT1AB 17503BA 107503 ME1AB 17504BA 107504 MF1LC 17501CC MS1LC 17502CC C10750 MT1LC 17503CC C107503 ME1LC 17504CC C107504 MF1LG 17501CG MS1LG 17502CG M
34、T1LG 17503CG ME1LG 17504CG MF1AR 17501RA MS1AR 17502RA MT1AR 17503RA ME1AR 17504RA LF1AB 17551BA LS1AB 17552BA 10755 LT1AB 17553BA 107553 LE1AB 17554BA 107554 LF1LC 17551CC LS1LC 17552CC C10755 LT1LC 17553CC C107553 LE1LC 17554CC C107554 LF1LG 17551CG LS1LG 17552CG LT1LG 17553CG LE1LG 17554CG See fo
35、otnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AA59832/2A 10 TABLE II. Commercial P/N supersession data Continued. PIN designator AA59832/02 Vendor similar designator or type part number 1/ CAGE 5BG68 Vendor similar designato
36、r or type part number 1/ CAGE 61081 LF1AR 17551RA LS1AR 17552RA LT1AR 17553RA LE1AR 17554RA 1/ The manufacturers P/N shall not be used for procurement to the requirements of this CID specification sheet. At the time of preparation of this CID specification sheet, the aforementioned commercial produc
37、ts were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph in AA59832. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extensiveness of th
38、e changes. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians: GSA FAS Army CR Navy EC Air Force 85 Preparing Activity: DLA CC DLA CC Review Activity: Project: 59982010052 Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
