1、 AMSC N/A FSC 4320 AN6201 Rev B 21 April 2011 SUPERSEDING AN6201 Rev A 22 March 1982 DETAIL SPECIFICATION SHEET PUMP-HYDRAULIC HAND This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall c
2、onsist of this specification sheet and MIL-DTL-5515. FIGURE 1. Hydraulic hand pump. EXTREME HIGH POSITION OF HANDLE C L DRILL # F (.257) 2 HOLES FOR MOUNTING 2.750 .005 MID POSITION OF HANDLE C L THIS PIVOT POINT LOCATES EXTREME HANDLE POSITIONS. PIVOT MAY BE ANYWHERE IN SHADED AREA. 2.000 .510 .005
3、 1.500 DIA. MAX. HANDLE SOCKET DATAIL .020 R MAX. DRILL #11 (.191) 1.000 .001 DIA. 1.625 DIA. MAX. 2.250 +.000 - .010 1.125 BOSS IN ACCORDANCE WITH AND10050 FOR .375 DIA. TUBE. (NO INTERNAL CHECK VALVE) 1.375 MAX. SYM. ABOUT 4.000 7.625 MAX .375 .375 1.75 2.813 45 3.563 C L WIDTH AT MOUNTING HOLES .
4、250 .500 C L DISCHARGE 2.875 .823 EXTREME LOW POSITION OF HANDLE C L C L C L CLEARANCE ALLOWED FOR HANDLE MOVEMENT USING ANY PIVOT IN SHADED AREA. .250 +.0 - 2.5 +.0 - 2.5 .375 .500 .375 4.500 .500 C L 1.5 BOSS AND10050 FOR .500 DIA. TUBE. (PROVIDE A BUILT-IN CHECK VALVE AT THIS POINT 35 1 .75 4.625
5、0 R .563 10 30 C L 30 INCH-POUND Inactive for new design after 19 January 1996. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AN6201 Rev B 2 Inches mm Inches mm .001 .005 .010 .020 .191 .250 .257 .375 .500 .510 .563 .750 .823 1.000 0.03 0.13 0.25 0
6、51 4.85 6.35 6.53 9.53 12.70 12.95 14.30 19.05 20.90 25.40 1.125 1.375 1.500 1.625 1.750 2.000 2.250 2.750 2.813 2.875 3.563 4.000 4.500 4.625 7.625 28.58 34.93 38.10 41.28 44.45 50.80 57.15 69.85 71.45 73.03 90.50 101.60 114.30 117.48 193.68 NOTES: 1. Dimensions are in inches. 2. Metric equivalent
7、s are given for information only. 3. Unless otherwise specified tolerances for three place decimals .010 inch (0.25 mm), angles 0.5. FIGURE 1. Hydraulic hand pump - Continued. REQUIREMENTS Dimensions, see figure 1. Part or Identifying Number (PIN): AN6201-1. Changes from previous issue. Marginal not
8、ations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-5515, this document references AND10050. CONCLUDING MATERIAL Custodians: Preparing activity: Army AV DLA - CC Navy - AS Air Force
9、 - 99 (Project 4320-2010-005) DLA - CC Review activities: Army AT Navy - SH Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
