1、REVISIONS LTR DESCRIPTION DATE APPROVED A Add source CAGE 91506. 19 October 1987 R. Marbais B Change marking requirement. Add caution note. 22 November 1988 R. Marbais C Change marking requirement. Change 86103 wire size from 36 AWG to 32 AWG. 15 May 1990 R. Marbais D Remove CAGE 22526 and add CAGE
2、8N187. 26 August 1998 C. W. Koeller E Change CAGE 14933 to 037SZ3. Remove references to DESC and change to DSCC. Remove 91506. 3 October 2002 R. Heber F Updating CAGE (8N187) PINs. Editorial changes throughout. 23 November 2009 Abdo Abdouni Prepared in accordance with ASME Y14.100 Source control dra
3、wing REV PAGE REV STATUS OF PAGES REV F F F F PAGE 1 2 3 4 PMIC N/A PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Gail Willis Original date of drawing 19 September 1986 CHECKED BY TITLE Carl Dello-Stritto CONNECTORS, RECEPTACLE, ELECTRICAL, LATCH HOUSINGS, DOUBLE ROW, .025 PO
4、STS APPROVED BY Richard Marbais SIZE CAGE CODE DWG. NO. 86038 A 037Z3 REV F PAGE 1 OF 4 AMSC N/A 5935-E831-002 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 8603
5、8 REV F PAGE 2 Inches mm .005 0.13 .010 0.25 .015 0.38 .038 0.97 .050 1.27 .100 2.54 .200 5.08 .550 12.70 .965 24.51 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, all tolerances are .005 (0.13 mm). FIGURE 1. Dimensions and co
6、nfigurations. (SEE TABLE I) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 86038 REV F PAGE 3 REQUIREMENTS: Shall meet the requirements of drawing number 86037. D
7、esign and construction: Dimensions and configuration: See figure 1 and table I. Interface: Drawing number 86103 contacts crimped to 22 AWG through 32 AWG wire, .100 inch (2.54 mm) centers, .025 inch (0.63 mm) round or square posts. Polarization pin see drawing 87121. Temperature range: -40C to +105C
8、 Materials: Housing: Black polyphenylene oxide-based resin in accordance with and shall meet the flammability requirements of UL 94 V-0. Dielectric withstanding voltage: 1,000 volts rms, 60 Hz, sea level. Contact retention: 6.5 pounds (3 Kg), minimum per position. Marking: The Part or Identifying N
9、umber (PIN) shall be marked on the housing and package in accordance with MIL-STD-1285. If size, surface conditions, or other design considerations dont allow for full marking on the part, marking on the package is only required. The PIN shall include the complete DSCC PIN, manufacturers name or CAG
10、E code, and date code. The marking shall be permanent and legible in accordance with method 215 of MIL-STD-202. The PIN shall be constructed using the follow format: 86038 - XX DSCC drawing Number of positions number (see table I) TABLE I. Number of positions. Number of positions Dimension A (mm) Nu
11、mber of positions Dimension A (mm) 04 06 08 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 .200 (5.08) .300 (7.62) .400 (10.16) .500 (12.70) .600 (15.24) .700 (17.78) .800 (20.32) .900 (22.86) 1.000 (25.40) 1.100 (27.94) 1.200 (30.48) 1.300 (33.02) 1.400 (35.56) 1.500 (38.10) 1.600 (40.64) 1.700 (43.1
12、8) 1.800 (45.72) 1.900 (48.26) 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 2.000 (50.80) 2.100 (53.34) 2.200 (55.88) 2.300 (58.42) 2.400 (60.96) 2.500 (63.50) 2.600 (66.04) 2.700 (68.58) 2.800 (71.12) 2.900 (73.66) 3.000 (76.20) 3.100 (78.74) 3.200 (81.28) 3.300 (83.82) 3.400 (86.36) 3.500 (8
13、8.90) 3.600 (91.44) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 86038 REV F PAGE 4 Approved sources of supply are listed herein. Additional sources will be add
14、ed as they become available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN Vendor CAGE number Vendor similar PIN 1/ 86038-04 8N187 65043-035LF-MIL 86038-06 8N187 65043-034LF-MIL 86038-08 8N1
15、87 65043-033LF-MIL 86038-10 8N187 65043-032LF-MIL 86038-12 8N187 65043-031LF-MIL 86038-14 8N187 65043-030LF-MIL 86038-16 8N187 65043-029LF-MIL 86038-18 8N187 65043-028LF-MIL 86038-20 8N187 65043-027LF-MIL 86038-22 8N187 65043-026LF-MIL 86038-24 8N187 65043-025LF-MIL 86038-26 8N187 65043-024LF-MIL 86
16、038-28 8N187 65043-023LF-MIL 86038-30 8N187 65043-022LF-MIL 86038-32 8N187 65043-021LF-MIL 86038-34 8N187 65043-020LF-MIL 86038-36 8N187 65043-019LF-MIL 86038-38 8N187 65043-018LF-MIL 86038-40 8N187 65043-017LF-MIL 86038-42 8N187 65043-016LF-MIL 86038-44 8N187 65043-015LF-MIL 86038-46 8N187 65043-01
17、4LF-MIL 86038-48 8N187 65043-013LF-MIL 86038-50 8N187 65043-012LF-MIL 86038-52 8N187 65043-011LF-MIL 86038-54 8N187 65043-010LF-MIL 86038-56 8N187 65043-009LF-MIL 86038-58 8N187 65043-008LF-MIL 86038-60 8N187 65043-007LF-MIL 86038-62 8N187 65043-006LF-MIL 86038-64 8N187 65043-005LF-MIL 86038-66 8N18
18、7 65043-004LF-MIL 86038-68 8N187 65043-003LF-MIL 86038-70 8N187 65043-002LF-MIL 86038-72 8N187 65043-001LF-MIL 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor name number and address 8N187 T.T.I 2601 Sylvania Cross Dr Fort Worth, TX 76137 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
