1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Update boilerplate paragraphs to current requirements. - ro 12-10-15 C. SAFFLE CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE
2、 REV PAGE REV STATUS OF PAGES REV A A A A A A A A A A A A A PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing YY-MM-DD CHECKED BY TOM HESS TITLE MICROCIRCUIT, LINEAR, DUAL OUTPUT, LOW DROPOUT, VOLTAG
3、E REGULATOR, MONOLITHIC SILICON 06-03-22 APPROVED BY RAYMOND MONNIN SIZE A CODE IDENT. NO. 16236 DWG NO. V62/06617 REV A PAGE 1 OF 13 AMSC N/A 5962-V008-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO
4、 SIZE A CODE IDENT NO. 16236 DWG NO. V62/06617 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance dual output, low dropout, voltage regulator microcircuit, with an operating temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative
5、 Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/06617 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.
6、2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 TPS767D301-EP Dual output, low dropout, voltage regulator 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 28 MO-153 Plastic small outline with thermal pad
7、 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking
8、 permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06617 REV A PAGE 3 1.3 Absolute maximum ratings. 1/ Input voltage range (VI) -0.3 V to 13.5 V 2/ Input voltage range (VI) : 1IN, 2IN, EN pins -0.3 V to VI+ 0.3 V Output volt
9、age (VO) : 1OUT, 2OUT pins 7 V RESET pin 16.5 V Peak output current Internally limited Electrostatic discharge (ESD) rating: Human body model (HBM) . 2 kV Continuous total power dissipation (PD) See dissipation rating table Operating virtual junction temperature range (TJ) -55C to +150C Storage temp
10、erature range (TSTG) -65C to +150C 1.4 Recommended operating conditions. 3/ Input voltage range (VI): 1IN, 2IN pins 2.7 V to 10 V 4/ Output current for each LDO 0 to 1 A 5/ Output voltage range (VO) : 1OUT, 2OUT pins 1.5 V to 5.5 V Operating virtual junction temperature (TJ) -55C to +125C 1.5 Dissip
11、ation rating table. 6/ Package Air flow (CFM) TA 25C power rating Derating factor above TA= 25C TA= 70C power rating TA= 85C power rating X 0 3.58 W 3.58C/W 1.97 W 1.43 W 250 5.07 W 5.07C/W 2.79 W 2.03 W 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to th
12、e device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ All vo
13、ltage values are with respect to network ground terminal. 3/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. 4/ To calculat
14、e the minimum input voltage for maximum output current, use the following equation: VI(min)= VO(max)+ VDO(max load). 5/ Continuous output current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the device operate under conditions beyond
15、 those specified in this paragraph for extended periods of time. 6/ This parameter is measured with the recommended copper heat-sink pattern on a four layer printed circuit board (PCB), 1 ounce copper on 4 inch x 4 inch ground layer. For more information, refer to manufacturer technical brief litera
16、ture number SLMA002. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06617 REV A PAGE 4 2. APPLICABLE DOCUMENTS JEDEC Solid State Technology Association JEDEC PUB
17、95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the JEDEC Office, 3103 North 10th Street, Suite 240-S, Arlington, VA 22201-2107 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked w
18、ith the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) ab
19、ove. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified here
20、in. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 3.5.3 Block diagram. The block diagram shall be as shown in figure 3. 3.5.4 Timing waveforms. The timing waveforms shall
21、 be as shown in figure 4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06617 REV A PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Symbol Condit
22、ions 2/Temperature, TJ Device type Limits Unit Min Max Output voltage 3/ VO1.5 V VO 5.5 V, -55C to +125C 01 0.97VO1.02VOV (adjustable) 10 A IO 1 A Output voltage 3/ VO4.3 V VI 10 V, -55C to +125C 01 3.201 3.366 V (3.3 V output) 10 A IO 1 A Quiescent current 3/ (GND current) for each LDO IO= 1 A -55C
23、 to +125C 01 125 A Output voltage 3/ 4/ line regulation for each LDO VO/ VOVO+ 1 V VI 10 V +25C 01 0.01 typical %/V Output noise voltage BW = 200 Hz to 100 kHz, VO= 1.8 V, IC= 1 A, CO= 10 F +25C 01 55 typical VRMSOutput current limit for each LDO VO= 0 V -55C to +125C 01 2 A Thermal shutdown junctio
24、n temperature +25C 01 150 typical C Standby current for each LDO 2.7 V VI 10 V, EN = VI-55C to +125C 01 10 A FB input current (adjustable) FB = 1.5 +25C 01 2 typical nA High level enable input voltage -55C to +125C 01 2 V Low level enable input voltage -55C to +125C 01 0.8 V Power supply 3/ ripple r
25、ejection f = 1 kHz, CO= 10 F +25C 01 60 typical dB Input current (EN ) EN = 0 V -55C to +125C 01 -1 1 A EN = VI-1 1 Load regulation +25C 01 3 typical mV Dropout voltage 5/ VO= 3.3 V, IO= 1 A -55C to +125C 01 575 mV See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networ
26、king permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06617 REV A PAGE 6 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 2/Temperature, TJ Device type Limits Unit Min Max Reset section M
27、inimum input voltage for valid RESET IO(RESET)= 300 A +25C 01 1.1 typical V Trip threshold voltage VOdecreasing -55C to +125C 01 92 98 %/V Hysteresis voltage Measured at VO+25C 01 0.5 typical %/V Output low voltage VI= 2.7 V, IO(RESET)= 1 mA -55C to +125C 01 0.4 V Leakage current V(RESET)= 7 V -55C
28、to +125C 01 1 A RESET time out delay +25C 01 200 typical mV 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all para
29、meters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Unless otherwise specified, VI= VO(nominal)+ 1 V, IO= 1 mA, EN = 0, and CO= 10 F. 3/ The minimum IN operating voltage is 2.7 V or VO(typical)+ 1 V
30、, whichever is greater. The maximum IN voltage is 10 V. 4/ If VO 1.8 V then VI(min)= 2.7 V, VI(max)= 10 V: Line regulation (mV) = ( % / V ) x ( VO( VI(max) 2.7 V ) / 100 ) x 1000 If VO 2.5 V then VI(min)VO+ 1 V, and VI(max)= 10 V: Line regulation (mV) = ( % / V ) x ( VO( VI(max) (VO+ 1 V ) / 100 ) x
31、 1000 5/ IN voltage equals VO(typical) 100 mV: adjustable output voltage set to 3.3 V nominal with external resistor divider. Dropout voltage of 1.8 V and 2.5 V is limited by input voltage range limitations. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH
32、S-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06617 REV A PAGE 7 Case X FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE
33、IDENT NO. 16236 DWG NO. V62/06617 REV A PAGE 8 Case X continued. Symbol Dimensions Inches Millimeters Min Max Min Max A - 0.047 - 1.20 A1 0.001 0.005 0.05 0.15 b 0.007 0.011 0.19 0.30 c 0.005 nominal 0.15 nominal D 0.377 0.385 9.60 9.80 e 0.025 BSC 0.65 BSC E 0.169 0.177 4.30 4.50 E1 0.244 0.259 6.2
34、0 6.60 L 0.019 0.029 0.50 0.75 n 28 leads 28 leads Notes: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. Body dimensions do not include mold flash or protrusions. Mold flash and protrusion shall not exceed 0.15 mm (0.006 inch) per side. 3. This package is
35、designed to be soldered to a thermal pad on the board. Refer to technical brief, power pad thermally enhanced package, manufacturer literature number SLMA002 for information regarding recommended board layout. This document is available from the manufacturer. 4. Falls within JEDEC MO-153. FIGURE 1.
36、Case outline continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06617 REV A PAGE 9 Device type 01 Case outline X Terminal number Terminal symbol 1 NC 2 NC
37、3 1GND 4 1EN 5 1IN 6 1IN 7 NC 8 NC 9 2GND 10 2EN 11 2IN 12 2IN 13 NC 14 NC 15 NC 16 NC 17 2OUT 18 2OUT 19 NC 20 NC 21 NC 22 2RESET 23 1OUT 24 1OUT 25 1FB/NC 26 NC 27 NC 28 1RESET NC = No internal connection FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking pe
38、rmitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06617 REV A PAGE 10 Terminal symbol I/O Description 1GND Regulator 1 ground. 1EN I Regulator 1 enable. 1IN I Regulator 1 input supply voltage. 2GND Regulator 2 ground. 2EN I Re
39、gulator 2 enable. 2IN I Regulator 2 input supply voltage. 2OUT O Regulator 2 output voltage. 2RESET O Regulator 2 reset. 1OUT O Regulator 1 output voltage. 1FB/NC I Regulator 1 output voltage feedback for adjustable version and no connect for fixed output version. 1RESET O Regulator 1 reset. NC No c
40、onnection. FIGURE 2. Terminal connections Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06617 REV A PAGE 11 Adjustable version (for each LDO) Fixed vo
41、ltage version (for each LDO) FIGURE 3. Block diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06617 REV A PAGE 12 NOTES: 1. Vresis the minimum input voltag
42、e for a valid RESET . The symbol Vresis not currently listed within EIA or JEDEC standards for semiconductor symbology. 2. VIT - Trip voltage is typically 5% lower than the output voltage (95% VO). FIGURE 4. Timing waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted witho
43、ut license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06617 REV A PAGE 13 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal do
44、cumentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with
45、the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of
46、the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of
47、 present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of supply at http:/www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Regulator 1 VO(V) Regulator 2 VO(V) Vendor part number V62/06617-01XE 01295 Adjustable (1.5 V to 5.5 V) 3.3 V TPS767D301MPWPREP 1/ The vendor item drawing establishes an administrative control number for identifying the item
