1、I INCH-POUND I MIL-C-44192A 18 July 1990 SUPERSEDING MIL-C-44192(GL) 2 July 1985 MILITARY SPECIFICATION CONTAINER, SHIPPING AND STORAGE, COAT (HANGER PACK) This specification is approved for use by all Departments and Agencies of the Department of Defense. 1, SCOPE 1.1 Scope. This specification cove
2、rs dress coat shipping and storage containers, plastic garment bags, hanger bars, and hangers. 1.2 Classification. Containers shall be of the following types as specified (see 6.2). Type I - 12 coats Type II - 6 coats Type III - 3 coats Type IV - 1 coat 2. APPLICABLE DOCUMENTS 2.1 Government documen
3、ts. 2.1.1 specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein, Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specif
4、ications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). I Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be used in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineeri
5、ng Center, Natick, MA 01760-5014 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8115 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduct
6、ion or networking permitted without license from IHS-,-,-MIL-C-44192A SPECIFICATIONS FEDERAL A-A- 1696 - Bag, Plastic (Garment) PPP-B-636 - Boxes, Shipping, Fiberboard STANDARDS 3 MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection MIL-STD-129 - Marking for Shipment and Storage MIL-
7、STD-147 - Palletized Unit Loads by Attributes (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Government publicatio
8、ns. The following document forms a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation, Unless otherwise specified, the issues of documents not listed
9、 in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Applications for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street,
10、Philadelphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or though libraries or other informational services.) 2.3 Order of precedence. In the event
11、of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified
12、(see 6.21, a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.3. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-6 v MIL-C-44192A 1 m 9999906 0438366 I m MIL-C-44 192A 3.2 Material, design, and construction. Q 3.
13、2.1 Containers. 3.2.1.1 Types I, II, and III. Types I, II, and III containers shall be in accordance with figure 1. Each container shall consist of a half slotted container (HSC) box body with a door for loading or dispensing and a partial telescoping lid. The box body shall be made of fiberboard co
14、nforming to class domestic, variety DW, grade 275, B and C flute, fabricated in accordance with PPP-B-636. The box body shall be scored, slotted, and stitched or glued to form a tube having four flaps of equal length with the outer flaps meeting on the bottom, and four 3 to 3-1/4 icch flaps folded t
15、o the .inside on the top. If required to accomodate the hanger bar (see 3.2.21, a surcut notch shall be utilized at the center of each lengthwise top edge. The door shall be on the widthwise panel opposite the manufacturers joint and be produced by cutting two 18-inch vertical slits down each corner
16、, joined by a horizontal score. The lid shall be a snug-fitting partial telescope, 20 inches in depth, fabricated in accordance with PPP-B-636 made of fiberboard conforming to class domestic, variety SW, grade 200 of PPP-B-636. When type I is closed, the outer flaps shall meet in the middle of the t
17、op with a gap not to exceed 1/4 inch, The inner flaps shall be the same length as the outer and shall overlap on the inside on type I only. When type II and III containers are closed, the outer flaps shall overlap across the width of the lid. 3.2.1.2 Type IV. The type IV container shall conform to f
18、igure 2 and to style OPF, variety CW, grade 200 of PPP-B-636. The inside dimensions of the container shall be 40 inches in length, 21 inches in width, and 2 inches in depth. Inner flaps shall be 3 to 3-1/4 inches in depth. One inner flap shall be provided with a hole as specified on figure 2 so that
19、 the hook of the hanger can pass through and be held within thecontainer. 3.2.2 Hanger bars. The length of the hanger bars (for type I, II, and III containers) shall be as specified in table I. shall be as specified in 3.2.2.1 or 3.2.2.2 (see 6.2), The hanger bars shall be fabricated from minimum 22
20、 gauge sheet steel. The style of the hanger bars TABLE I. Hanger bar length Container type Bar length between end clips (inches 2. 1/8) I II III 14 8 4 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-44172A 1 W 777770b 0438367 3 MI s MIL-C-4
21、4192A 3.2.2.1 Style A, Style A hanger bar shall be attached to %he interior side of the end clip. 3.2.2.2 Style B. Style B hanger bar shall extend through the interior side of the end clip and shall be attached to the exterior end clip. This bar shall require a surcut notch to be cut in the upper ed
22、ge of each lengthwise side of the container to accomodate the bar (see figure i). 3.2.3 Hanger. The hanger shall be a molded one piece body made of high impactpolypropylene material. The polypropylene body shall have nominal dimensions of 14, 16, or 17 inches in length, 1/2 inch in width, and a maxi
23、mum af 6 inches in height. The contour of the body shall be flat or slightly concave, which includes a supporting cross bar. The hanger body and hook shall not exceed 9 inches in height. The swivel type hook shall be a formed square hook, made of either a noncorrosive metal or a plated steel, of a m
24、inimum 8-gaiige wire. The hook shall be firmly secured into the body of the hanger. shall have no sharp edges exposed. The end of the hook shall be bent back on itself 3/8 2 1/8 inches and 3.2.3.1 Fit of hanger hook on hanger bar. The hook shall fit securely over the hanger bar without being able to
25、 be removed without first moving the hanger up 3/4 of an inch. 32.4 Plastic garment bag. The plastic garment bag shall conform to type II of A-A-1696. 3.3 Markings. 3.3.1 Compliance and certificate markings. Containers made to comply with this specification shall be imprinted with compliance and cer
26、tificate markings in accordance with PPP-B-636. 3.3.2 Special markings. Arrow markings, as specified in MIL-STD-129, shall appear on all type I, II, and III containers. 3.4 Workmanship. 3.4.1 Container workmanship. The completed container shall conform to the quality of product established by this s
27、pecification and shall be clean and free of frayed or torn edges, improperly aligned panels, improper scores and slots, and the marking shall be clear and legible, All dimensions of the container makers blank shall be accurately cut, scored, and slotted so that the assembled container parts fit clos
28、ely without undue binding. No flap shall project beyond an edge of the container by more than 1/8 inch when the container is set up and closed. All metal fasteners, staples, or stitching wire shall be well clinched, flush with or below theinterior and exterior surfaces of the corrugated fiberboard.
29、The occurrence of defects shall not exceed the applicable acceptable quality levels. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- e T MIL-C-44172A 1 H 7777706 04383b8 5 = MIL-C-44192A 3.4.2 Hanger end hanger bar workmanship. The finished hanger
30、s and hanger bars shall conform to the quality of product established by this specification and the occurrence of defects shall not exceed the applicable acceptable quality levels. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purcha
31、se order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspect
32、ion requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsib
33、ility for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the c
34、ontractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, th
35、is does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 0 4.1.2 Responsibility for dimensional requirements. Unless otherwise specified in the contract or purchase order, the contractor is responsible f
36、or ensuring that all specified dimensions have been met. When dimensions cannot be examined on the end item, inspection shall be made at any point, or at all points in the manufacturing process necessary to ensure compliance with all dimensional requirements. 4.1.3 Certificates of compliance. When c
37、ertificates of compliance are submitted, the Government reserves the right to inspect such items to determine the validity of the certification. 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a. b. First article inspection (see 4.3). Qualit
38、y conformance inspection (see 4.4). 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-VIL-C-Y419ZA 1 I 9999906 OL.138369 7 I S . 4.3 First article inspection. When a first article is required (see 3.1 and 6.2), it shall be examined for the defects sp
39、ecified in 4.4.2, 4.4.3 and 4.4.4. 4.4 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall be perfomed in accordance with MIL-STD-105, 4.4.1 Component and material inspection. In accordance with 4.1, components and materials shall be inspected in accordance with
40、 all the requirements of referenced documents unless otherwise excluded, amended, modified, or qualified in this specification or applicable purchase document. 4.4.2 Container visual examination, The hanger pack containers shall be examined in accordance with PPP-B-636, except the following defects
41、shall be included in the PPP-B-636 list of overall type defects, Examine Defect Type I, II and Surcut notches (when required) not as specified or not III containers located as specif ied Door not located as specified Base of door not scored as specified Base (scoring) of door not horizontal to the d
42、egree it does not serve its intended purpose Door corner vertical slits less than 17-3/4 or more than 18-1/4 inches in length Variation in length between two door corner vertical slits of more than 1/8 inch Score at base of door located below bottom of vertical slits Container bodies not fabricated
43、with B incorrect; illegible; of improper size, location, sequence, or method of application 5. PACKAGING 5.1 Packing. Packing shall be Commercial. 5.1.1 Commercial. 5.1.1.1 Complete container assemblies. Complete container assembl.ies shall be packed in accordance with ASTM D 3951. 5.1.1.2 Component
44、s when procured separately. When components are procured separately (see 6.2) they shall be packed in accordance with ASTM D 3951. 5.2 Palletization. When specified (see 6.2), complete container assemblies or components when procured separately (see 5.1.1.1 and 5.1.1.2) shall be palletized in accord
45、ance with MIL-STD-147. 5.3 Marking. In addition to any special marking required by the contract or purchase order, complete container assemblies, components when procured separately and palletized unit loads shall be marked in accordance with MIL-STD-129. 6. NOTES (This section contains information
46、of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use, The containers are for the shipment and storage of dress coats. 6.2 Acquisition requirements. Acquisition documents must specify the following: a. Title, number, and date of this specification. b. Type r
47、equired (see 1.2). c. Issue of DODISS to be cited in the solicitation, and if required, the specific issue of individual documents referenced (see 2.1.1, 2.2, and . 20.1.1). d, When a first article is required (see 3.1, 4.3, and 6.3). e, Hanger bar style required (see 3.2.2). f. When palletization i
48、s required (see 5.2). 6.3 First article. When a first article is required, it shall be inspected and approved under the appropriate provisions of FAR 52,209. The first article should be a preproduction sample. The contracting officer should 8 Provided by IHSNot for ResaleNo reproduction or networkin
49、g permitted without license from IHS-,-,- MIL-C-44172A 81 I 7977706 0438372 7 I MIL-C-44192A specify the appropriate type of first article and the number of units to be furnished. The contracting officer should also include specific instructions in acquisition documents regarding arrangements for selection, inspection, and approval of the first article. 6.4 Subject term (key word) listing. Garment bag Transport; dress coat 6.5 Changes from previou
