1、MIL-DTL-17813/4 29 August 2009 DETAIL SPECIFICATION SHEET EXPANSION JOINTS, PIPE, METALLIC, CORRUGATED BELLOWS, EXTERNALLY PRESSURIZED This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shal
2、l consist of this specification sheet and MIL-DTL-17813. FIGURE 1. Expansion joint, externally pressurized. AMSC N/A FSC 4730FLANGE OD B FLANGE FLANGED END LENGTH NOMINAL DRAIN PORT WELD END INTERNAL GUIDE RING LIFTING LUG MULTI-PLY STAINLESS STEEL BELLOWS EXTERNAL GUIDE RING DRAIN PORT INTEGRAL LIN
3、ER EQUIVALENT TO THE NOMINAL PIPE SIZE HEAVY WALL HOUSING INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17813/4 2 DN C-NPS inch (mm) Flange OD inch (mm) 1/ B (bolt circle diameter) inch (mm) 1/ 50 2 (50.8) 6 (152.4) 4.75 (120.7)
4、65 2.5 (76.2) 7 (177.8) 5.5 (139.7) 80 3 (76.2) 7.5 (190.5) 6 (152.4) 90 3.5 (101.6) 8.5 (215.9) 7 (177.8) 100 4 (101.6) 9 (228.6) 7.5 (190.5) 125 5 (127) 10 (254.0) 8.5 (215.9) 150 6 (152.4) 11 (279.4) 9.5 (241.3) 200 8 (203.2) 13.5 (342.9) 11.75 (298.5) 250 10 (254) 16 (406.4) 14.25 (362.0) 300 12
5、 (304.8) 19 ( 482.6) 17 (431.8) 350 14 (355.6) 21 (533.4) 18.75 (476.3) 400 16 (406.4) 23.5 (596.9) 21.25 (539.8) 450 18 (457.2) 25 (635) 22.75 (577.9) 500 20 (508) 27.5 (698.5) 25 (635) 550 22 (558.8) - - 600 24 (609.6) 32 (812.8) 29.5 (749.3) 1/ See ASME B16.5, flange dimensions,150 pound. NOTES:
6、1. Dimensions are in inches. Metric equivalents are given for information only. 2. The illustration is for identification purposes only and is not intended to restrict designs and shapes of fastening devices, which conform to the requirements and are within the envelope dimensions. FIGURE 1. Expansi
7、on joint, externally pressurized Continued. REQUIREMENTS: Design and construction: Dimensions and configuration: See figure 1. Construction: Externally pressurized expansion joints shall be constructed of welded metal piping. Each unit shall be constructed with both internal and external guide rings
8、. Each unit shall be equipped with a drain port to be located on the outer shell of the unit. The design shall incorporate a totally enclosed, externally pressurized stainless steel bellows that is protected from by a heavy-walled shroud designed for full line pressure. The bellows shall be of singl
9、e-ply, or multi-ply construction. The classification of the expansion joints covered under this specification sheet are as follows: Type I - shall have corrugated bellows. Class 4 - shall be of the externally pressurized variety either single or double bellows. The bellows in class 4 expansion joint
10、s shall be designed and manufactured in accordance with the EJMA Standards. Sizes up to and including 10 inches shall be formed from seamless tubing Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17813/4 3 or from a tube having only one long
11、itudinal welded seam. For sizes larger than 10 inches, more than one longitudinal seam is permissible. In no case will circumferential seams be accepted unless the requirements of a particular application require such construction and the design is approved by the agency concerned. Convolutions shal
12、l be symmetrical and of similar dimensions. Single or double bellows construction shall be specified in MIL-DTL-17813. Materials and finishes. Materials and finishes for the bellows and flanges shall be in accordance with MIL-DTL-17813. The Part or Identifying Number (PIN) consists of the letters M,
13、 the basic specification number, specification sheet number, size, type, class, pressure rating, and end connection. PIN example: M17813/4-3-I-4-150-W Referenced documents. In addition to MIL-DTL-17813, this document references the following: ASME B16.5 EJMA Standards Specification number Size Class
14、 M 17813 /4 - 3 - I - 4 - 150 - W M prefix Specification sheet number End connection (F for flange ends, W for weld ends, and V for Vanstone ends) Type Pressure rating Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17813/4 4 CONCLUDING MATER
15、IAL Custodians: Preparing activity: Army - AT DLA - CC Navy - SH Air Force - 99 (Project 4730-2009-102) DLA - CC Review activities: Army - CE Navy MC, SA Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
