1、AMSC N/A FSC 5935 MIL-DTL-21097/5G 23 June 2008 SUPERSEDING MIL-DTL-21097/5F 18 August 2005 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, PRINTED WIRING BOARD MALE ADAPTER, CONTACT SPACING (.200) ALTERNATE DUAL ROW, TYPE CS This specification is approved for use by all Departments and Agencies
2、of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-21097. NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerance is .010 (.25 mm) for three place decimals. 3. Metric equivalents are giv
3、en for information only. 4. Contacts shall be designated on the connector using numerals in the location shown. FIGURE 1. Alternate dual row contacts, type CS. Inches mm Inches mm Inches mm .001 .03 .084 2.13 .162 4.11 .002 .05 .093 2.36 .300 7.62 .003 .08 .100 2.54 .327 8.31 .005 .13 .125 3.18 .350
4、 8.89 .026 .66 .128 3.25 .370 9.40 .044 1.12 .137 3.48 .470 11.94 .062 1.57 .150 3.81 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-21097/5G 2Inches mm .003 .08 .004 .10 .006 .15 .052 1.32 .100 2.54 .128 3.25 .140 3.56 .200 5.08
5、281 7.14 .300 7.62 .350 8.89 NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerance is .010 (.25 mm) for three place decimals. 3. Metric equivalents are given for information only. FIGURE 2. Printed circuit board mounting and hole pattern. Provided by IHSNot for ResaleNo repro
6、duction or networking permitted without license from IHS-,-,-MIL-DTL-21097/5G 3TABLE I. Connector, electrical, male adapter, type CS, class b, no mounting provision A. Dimensions (inches) 1/ 2/ Dash number Style Size A (maximum) B 0.015 (0.38) C 0.005 (0.13) D 0.010 (0.25) 01 02 17 17 2 3 2.470 (62.
7、74) 2.470 (62.74) 2.200 (55.88) 2.200 (55.88) 1.600 (40.64) 1.600 (40.64) .122 (3.10) .153 (3.89) 03 04 23 23 2 3 3.070 (77.98) 3.070 (77.98) 2.800 (71.12) 2.800 (71.12) 2.200 (55.88) 2.200 (55.88) .122 (3.10) .153 (3.89) 05 06 29 29 2 3 3.670 (93.22) 3.670 (93.22) 3.400 (86.36) 3.400 (86.36) 2.800
8、71.12) 2.800 (71.12) .122 (3.10) .153 (3.89) 07 08 35 35 2 3 4.270 (108.46) 4.270 (108.46) 4.000 (101.6) 4.000 (101.6) 3.400 (86.36) 3.400 (86.36) .122 (3.10) .153 (3.89) 09 10 41 41 2 3 4.870 (123.70) 4.870 (123.70) 4.600 (116.84) 4.600 (116.84) 4.000 (101.6) 4.000 (101.6) .122 (3.10) .153 (3.89)
9、11 12 47 47 2 3 5.470 (138.94) 5.470 (138.94) 5.200 (132.08) 5.200 (132.08) 4.600 (116.84) 4.600 (116.84) .122 (3.10) .153 (3.89) 1/ Dimensions are in inches. 2/ Metric equivalents are given for information only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr
10、om IHS-,-,-MIL-DTL-21097/5G 4REQUIREMENTS Dimensions and configurations: See figure 1, figure 2, and table I. Mating receptacles: Shall be in accordance with MIL-DTL-21097/4. Finish: Gold plating in accordance with ASTM B488, type II, code C, class 1.27, over nickel plating in accordance with Append
11、ix A of MIL-DTL-38999, class 2, 30 to 150 microinches. Part or Identifying Number (PIN): M21097/5-(dash number from table I). Qualification: Not required. First article testing: First article testing shall be as specified in table II, tests shall be in accordance with MIL-DTL-21097. Sample size: 8 c
12、onnectors shall be subjected to the first article testing. All sample units shall be subjected to the inspections in group I. The sample units shall be divided equally into 2 groups of four and subjected to the inspection for their particular groups. TABLE II. First article tests . Inspection Group
13、I (8 samples) Visual and mechanical inspection Permeability Insulation resistance Dielectric withstanding voltage Contact resistance Group II (4 samples) Temperature cycling Shock Bond strength, body assembly Contact retention Resistance to soldering heat Resistance to solvents Group III (4 samples)
14、 Salt spray (corrosion) Low-signal level contact resistance Contact resistance Bond strength, body assembly Failures: One or more failures shall be cause for refusal to grant first article approval. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL
15、DTL-21097/5G 5Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bi
16、dders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-DTL-21097, this document references the following: MIL-DTL-21097/
17、4 MIL-DTL-38999 ASTM B488 CONCLUDING MATERIALS Custodians: Preparing activity: Army CR DLA - CC Navy EC Air Force 85 (Project 5935-2008-027) DLA CC Review activities: Army AR, AT, AV, CR4, MI Navy AS, MC, OS, SH NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
