1、AMSC N/A FSC 6110 MIL-DTL-22438/2C 03 May 2012 SUPERSEDING MIL-P-22438/2B 10 May 1977 DETAIL SPECIFICATION SHEET PANEL, RECEPTACLE, ENCLOSED, ELECTRICAL AND ELECTRONIC (SYMBOL NO. 755.3) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirem
2、ents for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-22438. FIGURE 1. Panel, receptacle, enclosed, electrical and electronics. INCH-POUND INACTIVE FOR NEW DESIGN AFTER 18 July 1997 Provided by IHSNot for ResaleNo reproduction or networking permitted w
3、ithout license from IHS-,-,-MIL-DTL-22438/2C 2 FIGURE 1. Panel receptacle, enclosed, electrical and electronic - continued. Ltr Inches mm Min Max Min Max A 13.109 13.141 332.969 333.781 B 8.859 8.891 225.019 225.831 C 3.859 3.891 98.019 98.831 D 3.047 3.079 77.394 78.207 E 1.515 1.547 38.481 39.294
4、NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are plus or minus .016 inch (0.406 mm). FIGURE 1. Panel receptacle, enclosed, electrical and electronic - Continued. Provided by IHSNot for ResaleNo reproductio
5、n or networking permitted without license from IHS-,-,-MIL-DTL-22438/2C 3 FIGURE 2. Wiring diagram and mounting dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-22438/2C 4 Ltr Inches mm Min Max Min Max A 11.484 11.516 291.694 292.5
6、06 B 5.734 5.766 145.644 146.456 C 5.734 5.766 145.644 146.456 D 2.859 2.891 72.619 73.431 E .390 .422 9.906 10.719 FIGURE 2. Wiring diagram and mounting dimensions - continued. REQUIREMENTS: Interface and physical dimensions: See figures 1 and 2. Panel material: Steel. Mounting: Designed for overhe
7、ad mounting. Electrical: Bus connection terminal posts: Split-bolt type preferred. All posts including ground shall accept maximum wire size AWG-3. Interior wiring: Type D-10 in accordance with MIL-DTL-16878/3. Retainer latch: MIL-DTL-2726/15, figure 1. Intended use: Ship structure mounted, at test
8、benches which require power at voltages or frequencies other than ship service. Part or Identifying Number (PIN): The PIN shall be M22438/2-001. Referenced documents. In addition to MIL-DTL-22438, this document references the following: MIL-DTL-2726/1 MIL-DTL-2726/3 MIL-DTL-2726/7 MIL-DTL-2726/9 MIL
9、DTL-2726/15 MIL-DTL-16878/3 The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contr
10、actors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-22438/2C 5 Cust
11、odians: Preparing activity: Navy - SH DLA - CC DLA - CC (Project 6110-2012-004) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
