DLA MIL-DTL-83731 25 A-2008 SWITCHES TOGGLE MOMENTARY FOUR POLE 4 AMPERES LOW LEVEL ENVIRONMENTALLY SEALED《环保密封的4安培低电平四极瞬时拨动开关》.pdf

上传人:unhappyhay135 文档编号:691224 上传时间:2018-12-30 格式:PDF 页数:8 大小:133.42KB
下载 相关 举报
DLA MIL-DTL-83731 25 A-2008 SWITCHES TOGGLE MOMENTARY FOUR POLE 4 AMPERES LOW LEVEL ENVIRONMENTALLY SEALED《环保密封的4安培低电平四极瞬时拨动开关》.pdf_第1页
第1页 / 共8页
DLA MIL-DTL-83731 25 A-2008 SWITCHES TOGGLE MOMENTARY FOUR POLE 4 AMPERES LOW LEVEL ENVIRONMENTALLY SEALED《环保密封的4安培低电平四极瞬时拨动开关》.pdf_第2页
第2页 / 共8页
DLA MIL-DTL-83731 25 A-2008 SWITCHES TOGGLE MOMENTARY FOUR POLE 4 AMPERES LOW LEVEL ENVIRONMENTALLY SEALED《环保密封的4安培低电平四极瞬时拨动开关》.pdf_第3页
第3页 / 共8页
DLA MIL-DTL-83731 25 A-2008 SWITCHES TOGGLE MOMENTARY FOUR POLE 4 AMPERES LOW LEVEL ENVIRONMENTALLY SEALED《环保密封的4安培低电平四极瞬时拨动开关》.pdf_第4页
第4页 / 共8页
DLA MIL-DTL-83731 25 A-2008 SWITCHES TOGGLE MOMENTARY FOUR POLE 4 AMPERES LOW LEVEL ENVIRONMENTALLY SEALED《环保密封的4安培低电平四极瞬时拨动开关》.pdf_第5页
第5页 / 共8页
点击查看更多>>
资源描述

1、AMSC N/A FSC 5930 INCH-POUND MIL-DTL-83731/25A 22 April 2008 SUPERSEDING MIL-DTL-83731/25 7 January 2008 DETAIL SPECIFICATION SHEET SWITCHES, TOGGLE, FOUR POLE, 4 AMPERES, LOW LEVEL, ENVIRONMENTALLY SEALED This specification is approved for use by all Departments and Agencies of the Department of De

2、fense. The requirements for acquiring the switches described herein shall consist of this specification sheet and MIL-DTL-83731. FIGURE 1. PC Terminals.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83731/25A 2FIGURE 2. Solder Lug Terminals.

3、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83731/25A 3FIGURE 3. Standard Hardware and Panel Cut-out.FIGURE 4. Standard and Short Levers Lengths.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

4、MIL-DTL-83731/25A 41 Locked Position 2 Locked Positions 3 Locked Positions FIGURE 5. Locking Levers.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83731/25A 5FIGURE 6. Terminal DimensionsREQUIREMENTS: Temperature characteristic: -40qC t

5、o +85qC.Shock type: (50 gs sine wave) method 213, test condition A, MIL-STD-202. Sinusoidal vibration grade: 1 (10 to 500 Hz). Operating characteristics: Enclosure Design: 3 (watertight). Finish: Shall be corrosion resistant, black and lusterless. Dielectric withstanding voltage: Sea level: 1,000 V

6、rms between terminals 2,000 V rms between poles 2,000 V rms between terminals and frame Electrical endurance: At 2A, 250VAC or 4A, 28VDC: 10,000 cycles. At low level (50mV, 10mA): 20,000 cycles Electrical ratings: (Maximum current/voltage rating with resistive load) 2A/250 VAC, 4A/125 VAC, or 4A/28

7、VDC Contact bounce: 2ms max. Sand and dust: Applicable. Explosion: Not Applicable. Low level circuit: Applicable. Qualification: Inspection table of MIL-DTL-83731 Inductive Load: Not Applicable. Lamp Load: Not Applicable. Seal: Sea level only. Provided by IHSNot for ResaleNo reproduction or networki

8、ng permitted without license from IHS-,-,-MIL-DTL-83731/25A 6Military Part or Identifying Number (PIN): The PIN shall consist of the prefix M83731/25, followed in order by the appropriate numeric designator for terminal style and plunger length. M 83731/25- X X X X XXMilitary designation Specificati

9、on sheet number Terminals 1 Solder Lug Terminals 2 PC Terminals Electrical Functions See Table I Momentary(See Table II) Fluorescent Tip 0 None 1 White tip to lever Levers10 Standard 12 Short Lever 1V 1 Locked Position 2V 2 Locked Positions 3V 3 Locked Positions Example: M83731/25-24B02V, PC Termina

10、ls, Momentary (ON-ON-MOM), No Tip, 2 Locked Position Lever.TABLE I. Electrical Functions9 ON OFF ON 8 ON OFF MOM 7 MOM Off MOM 6 ON - ON 4 ON ON ON TABLE II. MomentaryA Non-Momentary B 1/ ON ON MOMC 1/ MOM ON MOMD Momentary 1/ Function 4 Only. Provided by IHSNot for ResaleNo reproduction or networki

11、ng permitted without license from IHS-,-,-MIL-DTL-83731/25A 7FIGURE 8. Wiring for 3-Way Switches (Function 4).FIGURE 7. Terminal IdentificationFlatProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83731/25A 8TABLE III. Lever Positions and Conne

12、ctionsFunction I II III (Flat) 6 ON 1A-3A1C-3C1E-3E1G-3G - ON 1A-2A1C-2C1E-2E1G-2G 7 MOM OFF MOM 8 ON OFF MOM 9 ON 1A-2A1C-2C1E-2E1G-2G OFF ON1A-3A1C-3C1E-3E1G-3G 4 ON ONMOM1A-2A1C-2C1E-2E1G-2G ONONON1A-2A1C-3C1E-2E1G-3G ONMOMMOM1A-3A1C-3C1E-3E1G-3G The margins of this specification are marked with

13、vertical lines to indicate where modifications were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content ir

14、respective of the marginal notations. Referenced Documents: MIL-DTL-83731 MIL-STD-202 Custodians: Preparing activity: Army - CR DLA - CC Air Force - 11 Navy - EC (Project 5930-2008-075) DLA - CC Review activites: Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
  • ASTM C1181-2000(2005) Standard Test Methods for Compressive Creep of Chemical-Resistant Polymer Machinery Grouts《耐化学腐蚀共聚物机械灰浆压缩蠕变标准试验方法》.pdf ASTM C1181-2000(2005) Standard Test Methods for Compressive Creep of Chemical-Resistant Polymer Machinery Grouts《耐化学腐蚀共聚物机械灰浆压缩蠕变标准试验方法》.pdf
  • ASTM C1181-2000(2012) Standard Test Methods for Compressive Creep of Chemical-Resistant Polymer Machinery Grouts《耐化学性聚合物机械灰浆压缩蠕变的标准试验方法》.pdf ASTM C1181-2000(2012) Standard Test Methods for Compressive Creep of Chemical-Resistant Polymer Machinery Grouts《耐化学性聚合物机械灰浆压缩蠕变的标准试验方法》.pdf
  • ASTM C1182-1991(2007) Standard Test Method for Determining the Particle Size Distribution of Alumina by Centrifugal Photosedimentation《用离心测光沉淀法测定矾土的粒径分布用标准试验方法》.pdf ASTM C1182-1991(2007) Standard Test Method for Determining the Particle Size Distribution of Alumina by Centrifugal Photosedimentation《用离心测光沉淀法测定矾土的粒径分布用标准试验方法》.pdf
  • ASTM C1182-2009 Standard Test Method for Determining the Particle Size Distribution of Alumina by Centrifugal Photosedimentation《用离心测光沉淀法测定矾土的粒径分布用标准试验方法》.pdf ASTM C1182-2009 Standard Test Method for Determining the Particle Size Distribution of Alumina by Centrifugal Photosedimentation《用离心测光沉淀法测定矾土的粒径分布用标准试验方法》.pdf
  • ASTM C1182-2009(2014) Standard Test Method for Determining the Particle Size Distribution of Alumina by Centrifugal Photosedimentation《用离心测光沉淀法测定矾土粒径分布的标准试验方法》.pdf ASTM C1182-2009(2014) Standard Test Method for Determining the Particle Size Distribution of Alumina by Centrifugal Photosedimentation《用离心测光沉淀法测定矾土粒径分布的标准试验方法》.pdf
  • ASTM C1183 C1183M-2013 Standard Test Method for Extrusion Rate of Elastomeric Sealants《弹性体密封剂挤出速率标准试验方法》.pdf ASTM C1183 C1183M-2013 Standard Test Method for Extrusion Rate of Elastomeric Sealants《弹性体密封剂挤出速率标准试验方法》.pdf
  • ASTM C1183 C1183M-2013(2018) Standard Test Method for Extrusion Rate of Elastomeric Sealants.pdf ASTM C1183 C1183M-2013(2018) Standard Test Method for Extrusion Rate of Elastomeric Sealants.pdf
  • ASTM C1183-2004 Standard Test Method for Extrusion Rate of Elastomeric Sealants《弹性密封件挤压比的标准试验方法》.pdf ASTM C1183-2004 Standard Test Method for Extrusion Rate of Elastomeric Sealants《弹性密封件挤压比的标准试验方法》.pdf
  • ASTM C1183-2004(2008) Standard Test Method for Extrusion Rate of Elastomeric Sealants《弹性体密封件挤压比的把试验方法》.pdf ASTM C1183-2004(2008) Standard Test Method for Extrusion Rate of Elastomeric Sealants《弹性体密封件挤压比的把试验方法》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1