1、 MIL-DTL-83796/15A 26 April 2010 SUPERSEDING MIL-DTL-83796/15 11 August 2008 DETAIL SPECIFICATION SHEET HOSE ASSEMBLY, RUBBER, LIGHTWEIGHT, MEDIUM PRESSURE, INTERNAL SUPPORT COIL, FIELD ATTACHABLE END FITTINGS, FLARE TO FLANGE, WITH LOCKWIRE HOLE This specification is approved for use by all Departm
2、ents and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83796. FIGURE 1. Hose assembly styles, field attachable fittings, flare-to-flange. AMSC N/A FSC 4720 INCH-POUND Provided by IHSNot for Res
3、aleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83796/15A 2 FIGURE 1. Hose assembly styles, field attachable fittings, flare-to-flange Continued. Hose cut-off factor (HCOF). HCOF is calculated as shown in table I. TABLE I. Hose assembly, field attachable fittings, HCO
4、F, styles A thru U. Style Fitting ends MIL-DTL-83798 MIL-DTL-83797 hose cut off factor (HCOF) 1/ inches verses hose dash size number Fitting 1 Fitting 2 -08 -10 -12 -16 -20 -24 -32 A and B M83798/1 M83798/7 2.12 2.19 2.36 2.80 3.31 3.30 3.78 C and D M83798/1 M83798/8 2.19 2.36 2.68 3.21 3.65 3.99 4.
5、61 E and F M83798/1 M83798/9 2.12 2.32 2.70 3.27 3.77 4.17 4.90 G and H M83798/2 M83798/8 2.53 2.75 3.29 3.90 4.42 4.82 5.47 J and K M83798/2 M83798/9 2.46 2.71 3.31 3.96 4.54 5.00 5.76 L and M M83798/3 M83798/9 2.30 2.54 3.18 3.86 4.46 4.94 5.72 N and P M83798/2 M83798/7 2.46 2.58 2.97 3.98 3.08 4.
6、13 4.64 R and S M83798/3 M83798/7 2.30 2.41 2.84 3.39 3.90 4.07 4.60 T and U M83798/3 M83798/8 2.37 2.58 3.16 3.80 4.34 4.76 5.43 1/ Example of HOCF: for a -08, hose OD, 20-1/2 inch assembly length, style A, the bulk hose length = 20.50 - the HCOF = 20.50 -2.12 = 18.38. Bulk hose length required is
7、18.38 inches. Hose assembly length. The hose assembly length is calculated as shown on figure 2. Hose assembly elbow fitting drop height. Elbow fitting drop height B and C is calculated as shown on figure 2. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH
8、S-,-,-MIL-DTL-83796/15A 3 NOTES: 1. Drop height B and C can be found in the applicable MIL-DTL-83798 slash sheet specified in table I. 2. Hose length “L” is measured from one fitting end to another fitting end. FIGURE 2. Hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or netwo
9、rking permitted without license from IHS-,-,-MIL-DTL-83796/15A 4 Angular displacement. Angular displacement shall be as shown on figure 3. NOTES: 1. Angular displacement for hose assemblies with elbow fittings on both ends shall have the angular displacement between elbows, measured counter-clockwis
10、e from the centerline of the nearest fitting, positioned at six-o clock, to the centerline of the other fitting (see SAE-J517). 2. The near end of the connector shall be put in numerical order relative to the far end (see table I). Example: Near end adapter 45, far end 90. 3. Angular displacement sh
11、all be measured in degrees with a tolerance of 3 for lengths up to 2 feet (61 cm) and 5 for all lengths over 2 feet (61 cm). 4. The angular displacement shall be expressed in two digits number of degrees divided. 5. Making the angular determination in the wrong direction will result in an unacceptab
12、le part. FIGURE 3. Elbow fitting angular alignment. REQUIREMENTS Hose assemblies shall be specified on figures 1, 2, and 3. Fittings shall mate with parts in accordance with SAE-AS4395 and the mounting pad in accordance with MS33786, as applicable. Hose assembly length tolerance shall be in accordan
13、ce with MIL-DTL-83796. Internal support coil. Internal support coil shall be in accordance with Defense Supply Center Columbus drawing 08001. Sleeves shall be spot welded to end of spring to prevent damage to ID of hose assembly. Internal support coil length. The internal support coil length shall b
14、e the overall hose assembly length minus the sum of the overall lengths of each end fitting. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83796/15A 5 Size codes shall be as specified in table II. Flange fittings not available for sizes -03
15、 -04, -05, and -06. TABLE II. Size code. 1/ 2/ Dash number -08 -10 -12 -16 -20 -24 -32 Size code H J K M N P R Hose OD reference Inches fraction 1/2 5/8 3/4 1 1 1/4 1 1/2 2 Inches decimal .500 .625 .750 1.000 1.250 1.500 2.000 mm 12.70 15.88 19.05 25.40 31.75 38.10 50.80 1/ Dimensions are in inches
16、 2/ Metric equivalents are given for information only. Materials and finishes shall be in accordance with MIL-DTL-83796 and in table III. TABLE III. Material and finish code. Part or Identifying Number (PIN) code dash letter Material Plating finish Blank Aluminum Anodize in accordance with MIL-A-86
17、25, type II -T Titanium Anodized in accordance with SAE-AMS2488, type 2 or fluoride phosphated in accordance with SAE-AMS2486 PIN example: M83796 /15 H 08 2 F 06 T M83796/15H082F06T indicates - Hose assembly for 1/2 hose OD, 8 1/4 inches in length, style F, 30 between elbows, titanium alloy. Angle b
18、etween elbows to be specified in 5 increments, 30 / 5 = 06 (see figure 3) Style (see figure 1) Length in eighths of an inch (0 through 7) Length in inches (see figure 2) Size code (see table II) Specification sheet number Specification number Material/finish (see table III) Provided by IHSNot for Re
19、saleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83796/15A 6 Changes from previous issues. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MI
20、L-DTL-83796, this document references the following: MIL-A-8625 MIL-DTL-83797 MIL-DTL-83798 MS33786 08001 SAE-AMS2486 SAE-AMS2488 SAE-AS4395 SAE-J517 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AV DLA - CC Navy - AS Air Force - 99 (Project 4720-2009-030) DLA - CC Review activities: Ar
21、my - AT Navy - MC, SA Air Force - 71, 85 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
