1、Comments, suggestions, or questions on this document should be addressed to: Defense Supply Center, Columbus, ATTN: DSCC VAT, Post Office Box 3990, Columbus, Ohio 43218-3990 or by email Resistordla.mil. Since contact information can change, you may want to verify the currency of this address informa
2、tion using the ASSIST Online database at http:/assist.daps.dla.mil/. AMSC N/A FSC 5905 INCH-POUND MIL-PRF-12934/31F 25 August 2009 SUPERSEDING MIL-PRF-12934/31E 1 February 1999 PERFORMANCE SPECIFICATION RESISTORS, VARIABLE, WIREWOUND, PRECISION, STYLE RR4000 This specification is approved for use by
3、 all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-12934. 1. SCOPE 1.1 This specification covers the requirements for style RR4000, variable, wirewound, precision resistors. 1.2
4、 Part or Identifying number (PIN). Variable resistors covered by this specification must be identified by a PIN which must be in the following form. Single-section (cup) resistors RR4000 C 2 A 7 J 103 Style Function and shaft length (1.2.1) Class and center tap (1.2.2) Resistance temperature charact
5、eristic (1.2.3) Rotational life characteristic (1.2.4) Function conformity tolerance and resistance tolerance characteristic (1.2.5) Resistance (1.2.6) 1.2.1 Function and shaft length. The function and shaft length applicable to this specification is identified by a single symbol in accordance with
6、table I. TABLE I. Function and shaft length. Symbol Shaft length tolerance + 0.03125 (.79) 1/ Function A 2/ 0.375 (9.53) Linear B 2/ 0.500 (12.70) Linear C 0.625 (15.88) Linear D 0.750 (19.05) Linear E 0.875 (22.23) Linear F 1.000 (25.40) Linear 1/ Metric equivalents are in parentheses. 2/ Inactive
7、for new design, for logistical support only Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-12934/31F 21.2.2 Class and center tap. The class and center tap applicable to this specification are symbols 2, 3, 4, and 5. 1.2.3 Resistance temperat
8、ure characteristic. The resistance temperature characteristic applicable to this specification are symbols A to H, inclusive. 1.2.4 Rotational life characteristic. The rotational life characteristics applicable to this specification are symbols 7, 8, and 9. This potentiometer is capable of operation
9、s up to 100 rpm. 1.2.5 Function-conformity tolerance and resistance tolerance characteristics. The function-conformity tolerance and resistance tolerance characteristic applicable to this specification are symbols G to L, inclusive and S to X, Inclusive. 1.2.6 Resistance. The nominal total resistanc
10、e values and nominal resolution applicable to this specification is in accordance with table II. TABLE II. Nominal total resistance and nominal resolution characteristics Nominal total resistance value Nominal resolution Ohms Percent 100 0.070200 0.060500 0.050 1,000 0.0452,000 0.0355,000 0.025 10,0
11、00 0.01920,000 0.01650,000 0.012 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as ex
12、amples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, sta
13、ndards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-12934 - Resi
14、stors, Variable, Wirewound, Precision, General Specification for. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). 2.3 Order of precedence. In the
15、event of a conflict between the text of this document and the references cited herein (except for related specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Pr
16、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-12934/31F 33. REQUIREMENTS 3.1 General. The requirements for acquiring the product described herein shall consist of this document and MIL-PRF-12934. 3.2 Interface and physical dimensions. The res
17、istors shall meet the interface and physical dimensions specified in figure 1. Inches mm Inches Mm Inches mm Inches mm Inches mm .005 0.13 .020 0.51 .062 1.57 .250 6.35 .625 15.88 .010 0.25 .040 1.02 .080 2.03 .281 7.14 .875 22.23 .015 0.38 .060 1.52 .125 3.18 .313 7.95 Style Turns L (max) K (max) M
18、aximum continuous working voltage (volts) Power rating (watts) 1/ Maximum starting and running torque (ounce-inch) Stop-torque(pound-inch) Ten-turn single cup Per each additional ten-turn cup Starting Running Starting Running RR4000 Ten 1.500 (38.10) 1.500 (38.10) 300 2.0 .7 .6 .6 .5 3 1/ When ten t
19、urn units are ganged, all cups will be 75 percent of rated wattage. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. FIGURE 1. Style RR4000 105 MAX Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P
20、RF-12934/31F 43.3 Minimum total resistance. The minimum total resistance value shall be 100 ohms. 3.4 Maximum total resistance. The maximum total resistance value shall be 50,000 ohms. 3.5 Mechanical travel. The mechanical travel shall be 3600 degrees +10 degrees, -0 degrees. 3.6 Actual electrical t
21、ravel. The theoretical electrical travel shall be 3600 degrees +4 degrees, -0 degrees. 3.7 Ganged cups. There shall be no more than 2 cups ganged. 3.8 Phasing. For independent linearity the phasing between the cups shall be within +1 degree. This shall be measured, with respect to the first cup, sta
22、rting from the counterclockwise end point. 3.9 Function. The type of function applicable to this specification shall be independent linearity. 3.10 Weight. The maximum weight shall be 0.09 pounds and each additional cup shall be 0.06 pounds. 3.11 Pure tin. The use of pure tin, as an underplate or fi
23、nal finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.4). 4. VERIFICATIONS. 4.1 Sampling and inspection. Sampling and inspection procedures sha
24、ll be in accordance with MIL-PRF-12934. 5. PACKAGING. 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact t
25、he responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from t
26、he managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. The intended
27、 use specified in MIL-PRF-12934 will be applicable to this specification. 6.2 Acquisition requirements. Acquisition documents must specify the following: a. Title, number, and date of this specification, and the complete PIN (see 1.2). b. Unless otherwise specified (see 2.1), the versions of the ind
28、ividual documents referenced will be those in effect on the date of release of the solicitation.). c. Packaging instructions (see 5.1). 6.3 PIN. This specification requires a PIN that describes technology and appropriate references to associated documents (see 1.2 and 3.1). Provided by IHSNot for Re
29、saleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-12934/31F 56.4 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after
30、 manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. Fo
31、r additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.5 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a
32、 convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous i
33、ssue. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 Review activities (Project 5905-2009-034) Army - AR, AT, AV, CR4, MI Navy - AS, CG, MC, OS Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
