1、INCH-POUND MIL-PRF-39012/75C 16 November 2011 SUPERSEDING MIL-PRF-39012/75B 24 September 1986 PERFORMANCE SPECIFICATION SHEET CONNECTORS, PLUGS, ELECTRICAL, COAXIAL, RADIO FREQUENCY, SERIES SMC (CABLED, SOCKET CONTACT, RIGHT ANGLE, CLASS 2) This specification is approved for use by all Departments a
2、nd Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39012. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in parentheses. 3. Metric equivalents are given for information only. 4. Fo
3、r dimensions A, B, C and D see table I. 5. Wrench flats are to accommodate standard wrench opening in accordance with FED-STD-H28, appendix 10. 6. Dimension B defines the overall length of the connector when assembled to the cable. 7. Maximum overall diameter of the connector is .320 inch (8.13 mm).
4、 8. All undimensioned pictorial configurations are for reference purposes only. 9. Series SMC, socket contact interface in accordance with MIL-STD-348. FIGURE 1. General configuration. AMSC N/A FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,
5、MIL-PRF-39012/75C 2 TABLE I. Dash numbers, cross-reference, and dimensions. Dash No. M39012/75- # Applicable cable group from MIL-PRF-39012, appendix B M17/ Typical mating connector 1/ Dimensions Inches (millimeters) maximum 2/ CATEGORY A FIELD SERVICEABLE (NO SPECIAL TOOLS REQUIRED) 0003 3/ 4/ Cab
6、le group I 93-RG178 * 169-00001 % M39012/74-0003 M39012/76-0003 A B C D .63 (16.00) .80 (20.32) .50 (12.70) .67 (17.02) 0004 3/ 4/ Cable group II 113-RG316 * 172-00001 % 94-RG179 M39012/74-0004 M39012/76-0004 0103 3/ Cable group I 93-RG178 * 169-00001 % M39012/74-0103 M39012/76-0103 0104 3/ Cable gr
7、oup II 113-RG316 * 172-00001 % 94-RG179 M39012/74-0104 M39012/76-0104 0105 3/ 95-RG180 * M39012/74-0105 M39012/76-0105 4101 3/ Cable group I 93-RG178 * 169-00001 % M39012/74-4101 M39012/76-4101 4102 3/ Cable group II 113-RG316 * 172-00001 % 94-RG179 M39012/74-4102 M39012/76-4102 See notes at end of
8、table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/75C 3 TABLE I. Dash numbers, cross-reference, and dimensions Continued. Dash No. M39012/75- # Applicable cable group from MIL-PRF-39012, appendix B M17/ Typical mating connector 1/
9、Dimensions Inches (millimeters) maximum 2/ CATEGORY C FIELD REPLACEABLE (MIL-C-22520/5 BASIC CRIMP TOOL) 5/ 0011 3/ 4/ Cable group I 93-RG178 * 169-00001 % M39012/74-0011 M39012/76-0011 A B C D .63 (16.00) .80 (20.32) .50 (12.70) .67 (17.02) 0012 3/ 4/ Cable group IIa Example: M39012/73-3001 mates w
10、ith M39012/74-3001, and M39012/73-4001 mates with M39012/74-4001. NOT FOR ARMY, NAVY, OR AIR FORCE USE. FOR OEM USE ONLY Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/75C 10 TABLE V. Group qualification and retention testing. Group Su
11、bmission and retention of qualification of any of the following connectors 1/ M39012/ Qualifies the following connectors M39012/ I 75-0003 75-0003 75-0103 2/ II 75-0004 75-0004 75-0104 2/ III 75B0008 75B0008 75B0014 2/ IV 75B0009 75B0009 75B0010 75B0015 2/ 75B0016 2/ V 75B0010 75B0010 75B0016 2/ VI
12、75-0011 75-0011 75-0017 2/ VII 75-0012 75-0012 75-0018 2/ VIII 75-0013 75-0013 IX 75-0105 75-0105 1/ For qualification retention, where more than one part is listed in a group in this column, data may be supplied on any of those parts in order to retain qualification for those parts in the correspon
13、ding right hand column. 2/ Corrosion and contact resistance test data must be submitted to DSCC-VQ before qualification approval may be granted. NOTE: If a connector manufacturer produces a connector which meets all the requirements for two or more connector PINs (within the same series), the manufa
14、cturer may receive qualification approval for two or more connector PINs by qualifying the one connector. It is not necessary that such connectors be in the same group. Each connector, however, must be marked with its own appropriate PIN. For group qualification, the connectors must be of similar de
15、sign. Qualification of connectors qualifies connectors of the same material and finish only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/75C 11 TABLE VI. Cross reference of PIN. Preferred PIN M39012/75 1/ Substitute for PIN Or type
16、designation -0003 -0004 B0008 B0009 B0010 M39012/75-0001 M39012/75-0002 M39012/75-0008, M39012/75-0005 M39012/75-0009, M39012/75-0006 M39012/75-0010, M39012/75-0007 1/ The “B” PIN is required marking for connectors manufactured after 24 March 1987. The connectors that are in stock or distribution th
17、at were previously qualified and marked with the old PIN shall also be considered acceptable for Government use until stock is purged. (Applies to category “B” P/N change only; M39012/XXBXXXX). Changes from previous issue. The margins of this specification are marked with vertical lines to indicate
18、where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespectiv
19、e of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-PRF-39012, this document references the following: MIL-STD-348 MIL-DTL-22520 MIL-C-22520/5 MIL-PRF-39012/73 MIL-STD-202 ASTM B488 FED-STD-H28 CONCLUDING MATERIAL Custodians: Preparing ac
20、tivity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5935-2009-109) DLA - CC Review activities: Army - AT, AV, EA, MI Navy - AS, MC, OS, SA, SH Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
