1、AMSC N/A 1 of 3 FSC 4730 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. MS27077C 25 September 2003 SUPERSEDING MS27077B 2 May 1966 DETAIL SPECIFICATION SHEET FLANGE, SWIVEL, RETAINING This specification is approved for use by all Departments and Agencies of the Dep
2、artment of Defense. The requirements for acquiring the product described herein shall consist of this specification and MIL-DTL-27272. NOTES: 1. Reduction of dimensions by 7 max draft angle permissible if forged. 2. Diameters F and G shall be concentric within .010 full indicator movement (FIM). FIG
3、URE 1. Flange illustration. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27077C 2 REQUIREMENTS Intended use. This part is a component of MS27062, MS27064, and MS27066. This is a design standard for manufacturing purposes. The item is
4、only procured as an integral part of adapter assemblies. Identification of product. The Part or Identifying Number (PIN) for this part shall be as specified in table I (e.g., MS27077-8C). Dimensions and tolerances. Dimensions are in inches. Unless otherwise specified, break or radius all corners .00
5、5, +.005, -.000. Material. Corrosion-resistant steel, class 304, condition A, in accordance with SAE AMS-QQ-S-763. Finish. Passivate in accordance with SAE AMS-QQ-P-35. Remove all burrs and slivers. Flange illustration. See figure 1. Surface roughness. Unless otherwise specified, maximum surface rou
6、ghness shall not exceed 125 in. Rain accordance with ASME B46.1. Order of precedence. This specification takes precedence over the documents referenced herein. Unless otherwise specified, referenced documents shall be of the issue in effect on the date of solicitation. TABLE I. Flange requirements.
7、PIN MS27077 A 1/B .005 C .015 D .016 E +.010 -.000 -8C 1.390 .016 .950 1.782 .219 .205 -10C 1.468 1.038 1.906 -12C 1.594 1.156 2.094 -16C 1.750 1.312 2.312 -20C 2.188 .020 1.656 2.875 .266 .266 -24C 2.375 1.812 3.094 .281 PIN MS27077 F 2/+.005 -.000 G 2/+.010 -.000 H .5 J .016 K +.005 -.000 M 3/+.01
8、5 -.000 -8C .885 .750 20 .297 .136 .234 -10C 1.010 .880 -12C 1.260 1.125 -16C 1.510 1.375 18 -20C 1.854 1.688 16 -24C 2.135 1.938 .359 .168 .297 1/ Reduction of dimensions by 7 max draft angle permissible if forged. 2/ Diameters F and G shall be concentric within .010 full indicator movement (FIM).
9、3/ Part may be forged or machined from bar. If machined, thickness shall be to dimension M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27077C 3 Changes from previous issue. Marginal notations are not used in this revision to identify changes w
10、ith respect to the previous issue, due to the extent of the changes. CONCLUDING MATERIAL Custodians: Preparing activity: Army AV DLA - CC Navy - AS Air Force - 99 (Project 4730-0868-080) DLA - CC Review activities: Army - AR, AT, MI Navy - MC, SA, SH Air Force - 71 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
