1、AMSC N/A FSC 5340 MS35813E 17 SEPTEMBER 2009 SUPERSEDING MS35813D 27 FEBRUARY 1987 DETAIL SPECIFICATION SHEET CONNECTOR, ROD END - STEEL This specification sheet is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described her
2、ein shall consist of this specification sheet and procurement specification MIL-DTL-45918. LHAEMFIGURE 1. Connector. INCH-POUNDInactive for new design after 16 June 1997.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35813E 2TABLE I. Part Numbers
3、and Dimensions. PART NUMBER NOMINAL DIAMETER A LENGTH E THICKNESS OF BOSS +.00 -.01 H DIAMETER OF BOSS .03 L DIAMETER OF HOLE M WEIGTH (APPROX) LBS ULTIMATE (MIN) AXIAL LOAD LBS SIZE TOLERANCE +.0010 MS35813-1 .190 (#10) 1.25 .19 .38 .1875 -.0010 .02 1500 MS35813-2 .250 (1/4) 1.25 .28 .50 .2500 -.00
4、10 .03 2700 MS35813-3 .312 (5/16) 1.38 .34 .59 .3125 -.0010 .05 4200 MS35813-4 .375 (3/8) 1.50 .44 .69 .3750 -.0010 .08 6000 MS35813-5 .437 (7/16) 1.50 .50 .81 .4375 -.0010 .12 8200 MS35813-6 .500 (1/2) 1.75 .56 .94 .5000 -.0020 .18 10700 MS35813-7 .625 (5/8) 2.00 .69 1.19 .6250 -.0020 .34 16800 MS3
5、5813-8 .750 (3/4) 2.38 .81 1.44 .7500 -.0020 .59 24300 MS35813-9 .875 (7/8) 2.75 .94 1.29 .8750 -.0020 .91 33000 MS35813-10 1.000 3.00 1.06 1.94 1.0000 -.0020 1.32 43200 Requirements: 1. Material: Steel, carbon, SAE 1010, 1111, SAE C1015 C1029 or equivalent in accordance with SAE-AIR4127. These stee
6、ls shall have a minimum tensile strength of 55,000 psi. 2. Protective coating: Zinc coated (hot dip galvanized) in accordance with ASTM A123/A123M, Zinc (electrodeposited) in accordance with ASTM B633. 3. Surface roughness: Surfaces marked shall have 125 surface roughness in accordance with ASME B46
7、1. 4. Tolerance: Unless otherwise specified, tolerance shall be .03. 5. Dimensions: All dimensions specified are to be met after plating. Notes: 1. Unless otherwise specified, all dimensions are in inches. 2. Remove all burrs and sharp edges. 3. For design feature purposes, this standard takes prec
8、edence over procurement documents referenced herein. 4. Illustrations are for identification and are not intended to restrict the design or shapes not dimensioned. 5. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue
9、due to the extent of the changes. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35813E 3Custodians: Preparing Activity: Army - AR DLA -IS Navy - AS Air Force 99 (Project 5340-2009-027) Review activities: Army CR4, GL, MI Navy MC, OS, SH, YD NOTE:
10、 The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
