1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Added “Recommended power supply turn on sequence: -VEE, VREF, followed by +VEE“ to footnote 1 of the table I.Corrected footnote 3 on sheet 3. -sld 10-04-26 Charles F. Saffle REV SHEET REV A A A SHEET 15 16 17 REV STATUS REV A A A A A A A A A A A
2、A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Steve Duncan DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPAR
3、TMENT OF DEFENSE AMSC N/A APPROVED BY Charles F. Saffle MICROCIRCUIT, HYBRID, LINEAR, DUAL 16 CHANNEL, ANALOG MULTIPLEXER DRAWING APPROVAL DATE 10-02-03 REVISION LEVEL A SIZE A CAGE CODE 67268 5962-09232 SHEET 1 OF 17 DSCC FORM 2233 APR 97 5962-E281-10Provided by IHSNot for ResaleNo reproduction or
4、networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09232 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph
5、1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5
6、962 - 09232 01 K X C Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PR
7、F-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 MUX8532 Dual 16 channel analog multiplexer, h
8、igh impedance analog input 02 MUX8533 Dual 16 channel analog multiplexer, high impedance analog input with ESD protection 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PR
9、F-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H
10、 Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited tem
11、perature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that cl
12、ass. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturer
13、s internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09232 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL
14、 A SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 56 Ceramic quad flat pack 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-385
15、34. 1.3 Absolute maximum ratings. 1/ Positive supply voltage between +VEEand GND . +20 V dc Negative supply voltage between -VEEand GND . -20 V dc VREFto GND . +7.5 V dc Digital input overvoltage range: VEN (pins 13 and 44) . ( GND - .5)V VA(pins 14, 15, 16, and 17) ( GND - .5)V VB(Pins 40,41,42, an
16、d 43) . ( GND - .5)V Analog input overvoltage range: Device type 01 -30 V dc VIN +30 V dc Device type 02 -18 V dc VIN +18 V dc Power dissipation (PD), TC = -55C to +125C . 40 mW Thermal resistance junction-to-case (JC) 10C/W 2/ Storage temperature -65C to +150C Lead temperature (soldering, 10 second
17、s) +300C 1.4 Recommended operating conditions. Positive supply voltage (+VEE) 3/ . +15 V dc Negative supply voltage (-VEE) 3/ . -15 V dc VREF3/ +5 V dc Logic low level voltage (VAL) +0.8 V dc Logic high level voltage (VAH) +4.0 V dc Case operating temperature range (TC). -55C to +125C 2. APPLICABLE
18、DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF
19、 DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. _ 1/ Stresses above the absolute maximum ratings may cause
20、permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Based on the maximum power dissipation spread over the multiplexer die. 3/ Recommended power supply turn on sequence: -VEE, VREF, followed by +VEE.Provided by IHSNot for Resale
21、No reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09232 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Dr
22、awings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a
23、 conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual it
24、em performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable de
25、vice class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of
26、the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2
27、Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3. 3.2.4 Switching waveform(s). The switching waveform(s) shall be as specified on figure 4. 3.2.5 Block diagram. The block diagram shall be as s
28、pecified on figure 5. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requi
29、rements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers
30、vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for ea
31、ch device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon
32、 request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-
33、38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRC
34、UIT DRAWING SIZE A 5962-09232 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ -55C TC +125C unless otherwise specified Group A subgroups Device types Limits Unit Min
35、Max Supply currents +IEEVEN(0-15)= VEN(16-31)= VA(0-3)= VB(0-3)= 0 1,2,3 All 0 1 mA -IEE VEN(0-15)= VEN(16-31)= VA(0-3)= VB(0-3)= 0 1,2,3 All -1 0 mA +ISBY VEN(0-15)= VEN(16-31)= 4 V, VA(0-3)= VB(0-3)= 0 3/ 1,2,3 All 0 1 mA -ISBY VEN(0-15)= VEN(16-31)= 4 V, VA(0-3)= VB(0-3)= 0 3/ 1,2,3 All -1 0 mA A
36、ddress input currents IAL(0-3)AVA= 0 V 1,2,3 All -1 1 A IAH(0-3)A VA= 5 V 1,2,3 All -1 1 A IAL(0-3)BVB= 0 V 1,2,3 All -1 1 A IAH(0-3)BVB= 5 V 1,2,3 All -1 1 A Enable input current IENL(0-15) VEN(0-15)= 0 V 1,2,3 All -1 1 A IENH(0-15)VEN(0-15)= 5 V 1,2,3 All -1 1 A IENL(16-31) VEN(16-31)= 0 V 1,2,3 A
37、ll -1 1 A IENH(16-31)VEN(16-31)= 5 V 1,2,3 All -1 1 A See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09232 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEV
38、EL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ -55C TC +125C unless otherwise specified Group A subgroups Device types Limits Unit Min Max Positive input leakage current (CH0-CH31) +ISOFFOUTPUT(ALL) VIN= +10 V, VEN= 4 V, o
39、utput and all unused inputs = -10 V 4/ 5/ 1,2,3 01 -200 +200 nA 02 -100 +1000 Negative input leakage current (CH0-CH31) -ISOFFOUTPUT(ALL) VIN= -10 V, VEN= 4 V, output and all unused inputs = +10 V 4/ 5/ 1,2,3 01 -200 +200 nA 02 -100 +1000 Positive output leakage current outputs (pins 12 and 45) +IDO
40、FFOUTPUT(ALL) VOUT= +10 V, VEN= 4 V, output and all unused inputs = -10 V 5/ 6/ 1,2,3 All -100 +100 nA Negative output leakage current outputs (pins 12 and 45) -IDOFFOUTPUT(ALL) VOUT= -10 V, VEN= 4 V, output and all unused inputs = +10 V 5/ 6/ 1,2,3 All -100 +100 nA Input clamped voltage (CH0-CH31)
41、+VCLMP VEN = 4 V, all unused inputs are open 5/ 1 02 18.0 23.0 V 2 18.0 23.5 3 17.5 22.5 -VCLMP VEN = 4 V, all unused inputs are open 5/ 1 02 -23.0 -18.0 V 2 -23.5 -18.0 3 -22.5 -17.5 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license
42、from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09232 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ -55C TC +125C unless otherwise specified Grou
43、p A subgroups Device types Limits Unit Min Max Switch ON resistance outputs (pins 12 and 45) 8/ RDS(ON)(0-31)AVIN= +15 V, VEN= 0.8 V, IOUT= -1 mA 4/ 5/ 7/ 1,2,3 All 200 1000 RDS(ON)(0-31)BVIN= +5 V, VEN= 0.8 V, IOUT= -1 mA 4/ 5/ 7/ 1,2,3 All 200 1500 RDS(ON)(0-31)CVIN= -5 V, VEN= 0.8 V, IOUT= +1 mA
44、4/ 5/ 7/ 1,2,3 All 200 2500 Switching tests tAHLRL= 10 k, CL= 50 pF, See figure 4 9,10,11 All 10 1000 ns tALHRL= 10 k, CL= 50 pF, See figure 4 9,10,11 All 10 1000 ns tONENRL= 1 k, CL= 50 pF, See figure 4 9,10,11 All 10 1000 ns tOFFENRL= 1 k, CL= 50 pF, See figure 4 9,10,11 All 10 1000 ns 1/ +VEE = +
45、15 V dc, -VEE= -15 V dc, and VREF= +5 V dc, unless otherwise specified. Recommended power supply turn on sequence: -VEE, VREF, followed by +VEE.2/ Measure inputs sequentially. Ground all unused inputs. 3/ If not tested, shall be guaranteed to the limits specified in table I. 4/ VINis the applied inp
46、ut voltage to the input channels (CH0-CH31). 5/ VENis the applied input voltage to the enable lines EN(0-15) and EN(16-31). 6/ VOUTis the applied input voltage to the output lines OUTPUT1(0-15) and OUTPUT2 (16-31). 7/ Negative current is the current flowing out of each of the pins. Positive current
47、is the current flowing into each of the pins. 8/ The device types 01 and 02 cannot be operated with analog inputs from -15 V to -5 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09232 DEFENSE SUPPLY CENTE
48、R COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 Case outline X. FIGURE 1. Case outline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09232 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 9 DSCC FORM 2234 APR 97 Case outline X - Co
