1、LTR PME WA DATE (YR-MO-DA) APPROVED DESCRIPTION STANDARDIZED MILITARY DRAWING THIS DRAWING IS AVAILABLE OR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPAnTMENT OF DEFENSE DRAWING APPROVAL b1E 10 AUGUST 1988 REVISION LEVEL - -, dlstribullon is unlimited. Provided by IHSNot for ResaleNo reproduction
2、or networking permitted without license from IHS-,-,- _i_l-_. ._ _ DESC-DWG-88624 57 m 7779775 0033277 7 1. SCOPE 1.1 SCO e. This drawinglldescribes device requirements for class B microcircuits in accordance with l.Decification and standard, of the issue listed in that issue of the Department of De
3、fense Index of MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 pecifications and Standards specified in the solicitation, form a part of this drawing to the Nxtent specified herein. SPECIFICATION MI L I TARY MIL-M-38510 - Wicrocircuits, General Specification for. STANDARD REVIS
4、ION LEVEL SHEET 3 MILITARY MIL-STD-883 - Test Methods and Procedures for Microelectronics. (Copies of the specification and standard required by manufacturers in connection with specific cquisition functions should be obtained from the contracting activity or as directed by the ontracting activity.)
5、 -eferences cited herein, the text of this drawing shall take precedence. 2.2 Order of precedence. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with 1.2.1 of In the event of a conflict between the text of this drawing and the IIL-STD-883, “Provisions
6、 for the use of MIL-STD-883 in conjunction with compliant non-JAN devices“ nd as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical imensions shall be as specified in MIL-M-38510 and herein. 3.2.1 Terminal connections. The terminal connections
7、 shall be as specified on figure 1. 3.2.2 Mode Selection table. The mode selection table shall be specified on figure 2. 3.2.3 Functional diagram. 3.2.4 Case outline. The case outline shall be in accordance with 1.2.2 herein. The functional diagram shall be as specified on figure 3. 3.3 Electrical p
8、erformance characteristics. Unless otherwise specified, the electrical erfomance characteristics are as specified in table I and apply over the full case lperating temperature range. e marked with the part number listed in 1.2 herein. iay also be marked as listed in 6.4 herein n order to be listed a
9、s tn approved source of supply in 6.4. The certificate of compliance ,ubmitted to DESC-ECS prior to listing as an approved source of supply shall state that the ianufacturers product meets the requirements of MIL-STD-883 (see 3.1 herein) and the requirements ierein. 3.4 Marking. Marking shall be in
10、accordanc with MIL-STD-883 (see 3.1 herein). The part shall In addition, the manufacturers part number 3.5 Certificate of com liance. A certificate of compliance shall be required from a manufacturer 3.6 Certificate of conformance. A certificate of conformance as required in MIL-STD-883 (see 3.1 ier
11、ein) shall be provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ I_-_ ._.II_ DESC-DWG-b24 57 7777775 0033277 2 m TABLE I. Electrical performance characteristics. I I I I -55C 5 TC 5 +1
12、25OC L/ Isubgroupsl Min I Max I Condi ti ons I Group A I Limits IUnit ISymbo1 I I I I I I I Test High level output voltage VOH IVIN = VIH or VIL, IVcc = 4.5 VI 1,2,3 14.4 I IV IV N = V H or YIL, /Vcc = 4.5 VI 1,2,3 13.7 I IV l I doi 5 1.0 mA I I I I I IOv1 IV dol 5 4.0 mA I I I IOn4 IV I High level
13、input voltage VIH 12/ IVcc = 4.5 VI 1,2,3 12.0 I IV IOa8 IV 1l PA IIIol 5 20 PA I I I I I I I I I I I I I I I I I I I I I l VOL iypl=;$l VIL, IVCC = 4.5 VI 1,2,3 I l I I I I I I I I I I I l I I I I I I I I- I I I I I l I I I I I I I I I I I I I IIIN IVcc = 5.5 Y, VIN = Vcc or GND I I I VIN = Vcc or
14、GND, other inputs I I I I I IVCC = 5.5 v I I I I I I I I I I I I I I I I I Functional tests I (See 4.3.ld 171 I I I I I l I I Maximum clock frequency ?/ I fmax I I Low level output vol tage I !Vcc = 4.5 Vi 1,2,3 i IV N = V H or VIL, IVcc = 4.5 VI 1,2,3 I Low level input voltage /VIL 121 Quiescent cu
15、rrent /Ice IVcc = 5.5 V, VIN = Vcc or GND 1 1,2,3 i I160 IriA Input leakage current Additional quiescent currentlAICC IVIN 2.4 or 0.5 Y, any 1 input I 1,2,3 I 13.0 ImA _. . I 1,2,3 I I I Input capacitance /GIN /VIN = O Y, Tc = +25C, See 4.3.1 4 Il0 IPF 191 125 1MHz III I I I I I I I IVcc = 4*5 iee f
16、ootnotes at end of table. SIZE A 5962-88624 STANDARDIZED MILITARY DRAWING DEFENSE ELECTRONES SUPPLY CENTER REVISION LEVEL SHEET RAYTON. OHIO 45444 A DESC FORM 193A SEP a7 e- -: I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DESC-DWG-BBb24 57 W 777
17、7775 0013300 5 W SIZE A STANDARDIZED TABLE I. Electrical performance characteristics - Continued. I I I I I -55C 5 TC 5 +125OC L/ Isubgroupsl Min I Max i I I I I I I I I I 191 I ItpHL1, Ivcc = 5.0 V *lo%, I l, and clock to output I I I 10,ll I 169 I ns I I I I I I 1- I I 191 115 I ns I 1- ITHL I I 1
18、0,ll I 122 I ns Test Conditions I Group A I Limits IUnit ISymbol I I Propagation delay time, LE ltpLH1 ICL E 50 pF *IO% (see figure 4) (see figure 4) ITLH, I I I I I Transition time ?/ I I I I I I ,/ For a power supply of 5 V 110 percent, the worst case output voltages (VOH and VOL) occur for HCT at
19、 4.5 V. Thus, the 4.5 V values should be used when designing with this supply. Worst case VIH and VIL occur at Vcc = 5.5 V and 4.5 V respectively. !/ Test not required if applied as a forcing function for VOH or VOL. !/ Guaranteed, if not tested, to the specified limits. 5962-88624 3.7 Notification
20、of change. iith MIL-STD-883 ( see 3.1 herein). 3.8 Verification and review. DESC, DESCS agent, and the acquiring activity retain the option to *eview the manufacturers facility and applicable required documentation. Offshore documentation ;hall be made available onshore at the option of the reviewer
21、. Notification of change to DESC-ECS shall be required in accordance 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with iection 4 of MIL-M-38510 to the extent specified in MIL-STD-883 (see 3.1 herein). DESC FORM 193A SEP 87 , *
22、U. 8. GOMRNMENT PRINTING OFFCE 1888-549-W4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I I I I Device type I o1 I I I I I J I ITerminal number ITerminal symbol I I I I I I 1 I CP I I Package I I 5962-88624 CIZE A STANDARDIZED MILTTAW DRAWING DEFE
23、NSE ELECTRONICS SUPPLY CENTER RMSION LEVEL SHEET DAYTON, OH0 45444 LE i J1 I 52 I 53 I 54 I 516 I J 15 I 514 I 10 I J 13 I I I 11 I KC 12 I GND I 13 I I 14 I 15 I I I J 11 I J 10 I I 18 I J9 I 16 17 I I 58 I J1 I 19 I 56 I 20 I I 21 I I I 22 I 55 I 23 I Q I I I I 24 I “cc I I I I I FIGURE 1. Teminal
24、 connections. . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DESC-DWG-hZq 59 W 9799975 0013302 9 W - STANDARDIZED MILIARY DRAWING EFENSE ELECTRONICS SUPPLY Cm DAMON, OHK) 45444 Device type O1 5962-88624 SIZE A REVUON LEVEL SHEET 7 I I I I 1 Counte
25、r range I Mode I sel ec t I input I!, EP 87 r i ii U. 5. GOVERNMENT PRINTING OFFICE IBBB-548-BM Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-How to preset the 54/HCT4059 to desired r-N The value N is determined as follows: preset + 1 x decade 2 pr
26、eset) + decade 1 preset *MODE = First counting section divider (10, 8, 5, 4, or 2) To calculate preset values for any N count, divide the N count by the mode. The resultant is the corresponding preset values of the 5th through 2nd decade with the remainder being equal to the 1st decade value. N = (M
27、ODE*) (1000 x decade 5 preset + 100 x decade 4 preset + 10 x decade 3 N Preset value = -Mode Exampl e : N = 8479, Mode = 5 Mode select = 5, -5T-F -Preset values 1695 + 4 Program jam inputs (BCD) 4 I 51 52 53 54 55 56 57 J8 59 J10 511 512 JI3 514 515 JI6 LLHH HL H L HL L H LHHL To verify the ,results
28、, use equation 1: N = 5 (1000 X 1 + 100 x 6 + 10 x 9 + 1 x 5) + 4 N = 8479 FIGURE 2. Mode selection table - Continued. SIZE 5962-88624 A STANDARDIZED MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER REVISION LWEL SHEET 8 mm, OHIO 45444 1ESC FORM 193A %?US. ,OItRNMtNT IRINrlh(i OttlE: 19x7 lM4294WU
29、 SEP a7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- DESC-DUG-8624 57 7777775 OOL3304 2 1 w a: I I I! I I f o m O u) s a z r z + = H a a 3 Q 2 8 SIZE A 5962-88624 STANDARDIZED MILITARY DRAWING REVISION LEVEL SHEET 9 DEFENSE ELECTRONICC SUPPLY CEN
30、TER DAYK)N, OHIO 45444 DESC FORM 193A *US GOILRNMENT PRIMING OIRCE 1987 748429 600 SEP 87 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-i CP Pul I_* Q +. 4tf = 6ns -tr = 6 ns “cc ri 9oo/o - z 50/o 10% GND tw r 4 /i max -b 90% ,SO% I- l o O/O . -I-
31、“i /- “cc CP GND / FIGURE 4. Switching waveforms. STANDARDIZED MILITARY DRAWING 5962-88624 SIZE A I 1 SHEET 10 DEFEN!X ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 REVISION LEVEL ii U 8. QOVERNMENT WPHTING WFiCE 1W-!i4-W4 :SC FORM 193A SEP 87 Provided by IHSNot for ResaleNo reproduction or networkin
32、g permitted without license from IHS-,-,-DESC-DWG-b24 57 7777775 001330b b STANDARDIZED MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 I P SIZE A 5962-88624 RMSION LEVEL SHEET 11 4.2 Sciining. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be condu
33、cted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test method 1015 of MIL-STD-883. (i) Test condition A, B, C, or D using the circuit submitted with the certificate of compliance (see 3.5 herein). (2) TA = +125OC, minimum. Interim
34、and final electrical test parameters shall be as specified in table II herein, exce t interim electrical parameter tests prior to burn-in are optional at the discretion of tie manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with b. method 5005
35、of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 5, 6, and 8 in table I, method 5005 of MIL-STD-883 shall be-omitted. c. Subgroup 4 (GIN measurement) sh
36、all be measured only for the initial test and after process or design changes which may affect input capacitance. d. Subgroup 7 test sufficient to verify all 16 JAM inputs to truth table using all 5 modes, Function testing at fmax shall be done for initial test and after process or design changes wh
37、ich may affect the functionality of the device. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test method 1005 of MIL-STD-883 conditions: (1) Test condition A, B, C, or D using the circuit submitted with the certif
38、icate of compliance (see 3.5 herein). (2) TA = +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE II. Electrical test requirements. 1 I Subgroups I
39、I MIL-STD-883 test requirements. I (per method I I 5005, table I) I I I I i I i I i interim electrical parameters I - - I (method 5004) I I I I I I I I i Final electrical test parameters i 1*,2,9 I (method 5004) I I I I I I Group A test requirements i 1,2,3,4,7, i I I I I (method 5005) I 9,10,11 I i
40、 I i I Groups C and D end-point i 1,233 i I electrical parameters I I I (method 5005) I I I I I * PDA applies to subgroup 1. 5. PACKAGING 5.1 Packaging requirements. 6. NOTES !IL-M-38510. The requirements for packaging shall be in accordance with 6.1 Intended use. Microcircuits conforming to this dr
41、awing are intended for use when military ipecifications do not exist and qualified military devices that will perform the required function ire not available for OEM application. When a military specification exists and the product covered ?y this drawing has been qualified for listing on QPL-38510,
42、 the device specified herein will be nactivated and will not be used for new design. The QPL-38510 product shall be the preferred item or all appTications. 6.2 Re laceabilit 6.3 Comments. Comnents on this drawing should be directed to DESC-ECS, Dayton, Ohio 45444, or Microcircuits covered by this dr
43、awing will replace the same generic device :overedMir-prepared specification or drawing. :elephone96-5375. r SIZE A 5962-88624 STANDARDIZED MILITARY DRAWING DEFENCE ELECTRONICS SUPPLY CENTER REVISION LEVEL SHEET DAYTON, Oil 45444 12 )ESC FORM 193A SEP 87 Provided by IHSNot for ResaleNo reproduction
44、or networking permitted without license from IHS-,-,-DESC-DWG-BBhZq 57 7777775 0013308 T 6.4 Approved source of supply. An approved source of supply is listed herein. Additional jopces will be added as they become available, The vendor listed herein has agreed to this drawing ind a certificate of co
45、mpliance (see 3.5 herein) has been submitted to DESC-ECS. Vendor Vendor 1 Military drawing I CAGE similar part I I part number I .number I number A/ I I I I I I i I I 1 I I I I I 5962-8862401JX I 18714 I CD54HCT4055/3A I - i/ Caution. Do not use this number for item acquisition. Itemsquired by this
46、number may not satisfy the perforniance requirements of this drawing. Vendor CAGE nuniber 18714 Vendor name and address GE/RCA Corporation Route 202 Somervi 11 e, NJ 08876 STAN BARDI ZED SIZE A- 5962-88624 MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER RMSW LEVEL SHEET DAYTON, ii10 45444 13 DESC FORM 193A SEP 87 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
