1、REVISIONSLTR DESCRIPTION DATE (YR-MO-DA) APPROVEDA Drawing updated to reflect current requirements. - ro 00-10-27 R. MONNINTHE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.REVSHEETREVSHEETREV STATUS REV AAAAAAAAOF SHETS SHET 12345678PMIC N/A PREPARED BY RICK C. OFFICERDEFENSE SUPPLY CENTER
2、 COLUMBUSSTANDARDMICROCIRCUITDRAWINGCHECKED BYCHARLES E. BESORECOLUMBUS, OHIO 43216THIS DRAWING IS AVAILABLEFOR USE BY ALLDEPARTMENTSAPPROVED BYMICHAEL A. FRYEMICROCIRCUIT, LINEAR, HIGH SPEED, WIDEBANDWIDTH, OPERATIONAL AMPLIFIER, AND AGENCIES OF THEDEPARTMENT OF DEFENSEDRAWING APPROVAL DATE90-05-09
3、MONOLITHIC SILICONAMSC N/AREVISION LEVELASIZEACAGE CODE672685962-90535SHEET1 OF 8DSCC FORM 2233APR 97 5962-E415-00DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDAR
4、DMICROCIRCUIT DRAWINGSIZEA5962-90535DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000REVISION LEVELASHEET2DSCC FORM 2234APR 971. SCOPE1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits inaccordance with MIL-PRF-38535, appendix A
5、.1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:5962-90535 01 G X G7EG7EG7EG7EG7EG7EG7EG7EG7E G7E G7E G7E Drawing number Device type Case outline Lead finish(see 1.2.1) (see 1.2.2) (see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit f
6、unction as follows:Device type Generic number Circuit function01 OP64A High-speed, wide-bandwidthoperational amplifier1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:Outline letter Descriptive designator Terminals Package styleG MACY1-X8 8 CanP GDIP1-T or
7、CDIP2-T8 8 Dual-in-line2 CQCC1-N20 20 Square leadless chip carrier1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.1.3 Absolute maximum ratings.Supply voltage (G72VS)G7218 V dcDifferential input voltage 20 VInput voltage (VIN) .Supply voltageDisable input voltageSupply
8、 voltageOutput short-circuit duration.10 secondsPower dissipation (PD).500 mWStorage temperature range-65G71C to +175G71CLead temperature (soldering, 10 seconds) +300G71CMaximum junction temperature (TJ).+175G71CThermal resistance, junction-to-case (G54JC)See MIL-STD-1835Thermal resistance, junction
9、-to-ambient (G54JA):Case G .150G71C/WCase P119G71C/WCase 2 120G71C/W1.4 Recommended operating conditions.Supply voltage (G72VS)G7215 V dcAmbient operating temperature range (TA)-55G71C to +125G71CProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDA
10、RDMICROCIRCUIT DRAWINGSIZEA5962-90535DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000REVISION LEVELASHEET3DSCC FORM 2234APR 972. APPLICABLE DOCUMENTS2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form apart of this drawing to the
11、extent specified herein. Unless otherwise specified, the issues of these documents are those listedin the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited inthe solicitation.SPECIFICATIONDEPARTMENT OF DEFENSEMIL-PRF-38535 - Integrated Ci
12、rcuits, Manufacturing, General Specification for.STANDARDSDEPARTMENT OF DEFENSEMIL-STD-883 - Test Method Standard Microcircuits.MIL-STD-973 - Configuration Management.MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.HANDBOOKSDEPARTMENT OF DEFENSEMIL-HDBK-103 - List of Standard Mi
13、crocircuit Drawings (SMDs).MIL-HDBK-780 - Standard Microcircuit Drawings.(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the StandardizationDocument Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)2.2 Order of precedence
14、. In the event of a conflict between the text of this drawing and the references cited herein, the textof this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless aspecific exemption has been obtained.3. REQUIREMENTS3.1 Item requirements. Th
15、e individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified ManufacturerListing (QML) certified and qualified manufacturer or a manufacturer who has been
16、granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifyingactivity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) planmay make modifications to th
17、e requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used.3.2 Design,
18、construction, and physical dimensions. The design, construction, and physical dimensions shall be asspecified in MIL-PRF-38535, appendix A and herein.3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein.3.2.2 Terminal connections. The terminal connections shall be as s
19、pecified on figure 1.3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics areas specified in table I and shall apply over the full ambient operating temperature range.Provided by IHSNot for ResaleNo reproduction or networking permi
20、tted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA5962-90535DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000REVISION LEVELASHEET4DSCC FORM 2234APR 97TABLE I. Electrical performance characteristics.Test SymbolConditions 1/-55G71C G64 TA G64 +125G71CGroup AsubgroupsDevicetypeLi
21、mits Unitunless otherwise specified Min MaxInput offset voltageVOS101 1.0mV2, 3 2.0Input offset currentIOS101 1.0G50A2, 3 2.0Input bias currentIB101 1.0G50A2, 3 2.0Common mode 2/rejectionCMRVCM= IVR = G7211 V10190 dB2, 3 86Power supplyrejection ratioPSRRG72VS= G725 V to G7218 V1 01 17.8 G50V/V2, 3 3
22、1.6Supply currentISYVO= 0 V, no load101 8.0mA2, 3 8.5Disable supplycurrentISY/ Disable = 0 V101 1.0mADISOutput voltage swingVORL= 2 kG3A4, 5, 6 01 G7211.0 VRL= 200 G3A4 G7210.05, 6 G727.5Large signal voltagegainAVORL= 2 kG3A, VO= G7210 V40130 V/mV5, 6 20RL= 200 G3A, VO= G725 V4 12.55, 6 7.5See footn
23、otes at end of table.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA5962-90535DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000REVISION LEVELASHEET5DSCC FORM 2234APR 97TABLE I. Electrical performance characteri
24、stics Continued.Test SymbolConditions 1/-55G71C G64 TA G64 +125G71CGroup AsubgroupsDevicetypeLimits Unitunless otherwise specified Min MaxGain bandwidth GBWAVCL= +5 V, TA= +25G71C70175 MHzSlew rate SRAVCL= +5 V 3/7, 8 01 130.0 V/G50s1/ Unless otherwise specified, G72VS= G7215 V, RS= 50 G3A, and VCM=
25、 0 V.2/ IVR is defined as the VCMrange used for the CMR test.3/ Effective load resistance is 1 kG3A which is the parallel combination of the feedback resistance (2 kG3A) and the loadresistance (2 kG3A).3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specifie
26、d in table II. The electricaltests for each subgroup are described in table I.3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PINlisted in 1.2 herein. In addition, the manufacturers PIN may also be marked as listed in MIL-HDBK-103 (see 6.
27、6 herein). Forpackages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has theoption of not marking the “5962-“ on the device.3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed a
28、s anapproved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior tolisting as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein.3.7 Certifica
29、te of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be providedwith each lot of microcircuits delivered to this drawing.3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535,appendix A.3.9 Verificat
30、ion and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturersfacility and applicable required documentation. Offshore documentation shall be made available onshore at the option of thereviewer.Provided by IHSNot for ResaleNo reproduction or networking pe
31、rmitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA5962-90535DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000REVISION LEVELASHEET6DSCC FORM 2234APR 97Device type 01Case outlines G and P 2Terminal number Terminal symbol1 NULL NC2 -IN NULL3+INNC4-VSNC5 NULL -IN6 OUT NC7+VS+IN
32、8 DISABLE NC9 - NC10 -VS11 - NC12 - NULL13 - NC14 - NC15 - OUT16 - NC17 -+VS18 - NC19 - NC20 - DISABLENC = No connectionFIGURE 1. Terminal connections.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA5962-90535DEFENSE
33、SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000REVISION LEVELASHEET7DSCC FORM 2234APR 974. QUALITY ASSURANCE PROVISIONS4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,appendix A.4.2 Screening. Screening shall be in accordance with method 5004
34、 of MIL-STD-883, and shall be conducted on all devicesprior to quality conformance inspection. The following additional criteria shall apply:a. Burn-in test, method 1015 of MIL-STD-883.(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revisionl
35、evel control and shall be made available to the preparing or acquiring activity upon request. The test circuit shallspecify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified intest method 1015 of MIL-STD-883.(2) TA= +125G71C, minimum.b. Interi
36、m and final electrical test parameters shall be as specified in table II herein, except interim electrical parametertests prior to burn-in are optional at the discretion of the manufacturer.4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 ofM
37、IL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply.4.3.1 Group A inspection.a. Tests shall be as specified in table II herein.b. Subgroups 9, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted.4.3.2 Groups C and D inspections.a. End-
38、point electrical parameters shall be as specified in table II herein.b. Steady-state life test conditions, method 1005 of MIL-STD-883.(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revisionlevel control and shall be made available to the pre
39、paring or acquiring activity upon request. The test circuitshall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intentspecified in test method 1005 of MIL-STD-883.(2) TA = +125G71C, minimum.(3) Test duration: 1,000 hours, except as permitted by meth
40、od 1005 of MIL-STD-883.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDMICROCIRCUIT DRAWINGSIZEA5962-90535DEFENSE SUPPLY CENTER COLUMBUSCOLUMBUS, OHIO 43216-5000REVISION LEVELASHEET8DSCC FORM 2234APR 97TABLE II. Electrical test requirements.M
41、IL-STD-883 test requirements Subgroups(in accordance withMIL-STD-883, method 5005,table I)Interim electrical parameters(method 5004)1Final electrical test parameters(method 5004)1*,2,3,4,5,6,7Group A test requirements(method 5005)1,2,3,4,5,6,7,8,Groups C and D end-pointelectrical parameters(method 5
42、005)1* PDA applies to subgroup 1.5. PACKAGING5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.6. NOTES6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications(original equi
43、pment), design applications, and logistics purposes.6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by acontractor-prepared specification or drawing.6.3 Configuration control of SMDs. All proposed changes to existing SMDs will be coordinated wit
44、h the users of record forthe individual documents. This coordination will be accomplished in accordance with MIL-STD-973 using DD Form 1692,Engineering Change Proposal.6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system applicationrequires con
45、figuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used forcoordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962)should contact DSCC-VA, telephone (614) 692-0525.6.5 Comments. Comment
46、s on this drawing should be directed to DSCC-VA, Columbus, Ohio 43216-5000, or telephone(614) 692-0674.6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein
47、) has been submitted to and acceptedby DSCC-VA.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING BULLETINDATE: 00-10-27Approved sources of supply for SMD 5962-90535 are listed below for immediate acquisition information on
48、ly andshall be added to MIL-HDBK-103 during the next revision. MIL-HDBK-103 will be revised to include the addition ordeletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has beensubmitted to and accepted by DSCC-VA. This bulletin is superseded by the next dated revision of MIL-HDBK-103.Standardmicrocircuit drawingPIN 1/VendorCAGEnumberVendorsimilarPIN 2/5962-9053501GA 3/ OP64AJ/8835962-9053501PA 3/ OP64AZ/8835962-90535012A 3/ OP
