1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add case outline U. Add vendor CAGE 69210 for device type 01UX. Editorial changes throughout. 93-04-27 M. A. FRYE B Add footnote 2/ to VLT, VRIN, VRIT, and VONtests as specified under Table I. Add new footnote 2/ at the end of table I which state
2、s; “If not tested, shall be guaranteed to the limits specified in table I herein”. Changes in accordance with NOR 5962-R133-96. 96-05-23 M. A. FRYE C On the case outline U drawing, delete the single nominal dimension of .065 and substitute with .000 minimum and .065 maximum dimensions. Changes in ac
3、cordance with NOR 5962-R186-96. 96-08-12 R. MONNIN D Add case outline E for vendor CAGE 27014. Updated boilerplate. Editorial changes throughout. Redrawn. 97-05-16 R. MONNIN E Change to the output impedance test in table I. Updated boilerplate. - rrp 99-03-25 R. MONNIN F Add case outline X for vendo
4、r CAGE 27014. Changes to 1.2.4, JCand JAin 1.3, dropout voltage test in table I, and figures 1 and 2. - rrp 99-09-07 R. MONNIN G Add case outlines M and N for CAGE code 69210. Make changes to 1.2.4, 1.3, figure 1, and figure 2. - rrp 02-03-20 R. MONNIN H Update the case outline X descriptive designa
5、tor under 1.2.4 and delete figure 1 - ro 08-05-02 R. HEBER REV SHET REV SHET REV STATUS REV H H H H H H H H H H H H OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY JOSEPH A. KERBY DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY CHARLES E. BESORE COLUMBUS, OHIO
6、 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY MICHALE A. FRYE AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-12-18 MICROCIRCUIT, LINEAR, 12-VOLT REGULATOR, MONOLITHIC SILICON AMSC N/A REVISION LEVEL H SIZE A CAGE CODE 67268 59
7、62-90884 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E286-08 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90884 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 2 DSCC FORM 2234
8、 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). W
9、hen available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90884 01 Q E A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4)
10、Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA le
11、vels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 LM2940-12 1.0 A, low dropout, 12 volt regulator 1.2.3 Device class designa
12、tor. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appe
13、ndix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line M See figure 1 3 Flange mount, glass seal
14、ed, with gullwing leads N CBCC1-N3 3 Bottom terminal chip carrier U See figure 1 3 TO-257, flange mounted package with isolated tab, glass sealed X GDFP1-G16 16 Flat pack with gullwing leads Y MBFM1-P2 2 Flange mount 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device clas
15、ses Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90884 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 3 DSCC FORM 2
16、234 APR 97 1.3 Absolute maximum ratings. 1/ Input voltage (VIN): Survival voltage ( 100 ms ) 60 V dc Operational voltage 26 V dc Storage temperature range -65C to +150C Internal power dissipation (PD) Internally limited Lead temperature (soldering, 10 seconds) 300C Junction temperature (TJ) +150C Th
17、ermal resistance, junction-to-case (JC): Cases E and U . 3C/W Case M . 7.6CW Case N . 5.9C/W Cases X and Y . 5C/W Thermal resistance, junction-to-ambient (JA): Case E . 73C/W Case M . 60C/W Case N . 80C/W Case U . 50C/W Case X . 122C/W Case Y . 40C/W 1.4 Recommended operating conditions. Ambient ope
18、rating temperature range (TA) . -55C to +125C Output current (IO) 1 A Input voltage (VIN) . 17 V dc 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless
19、 otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MI
20、L-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:
21、/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect r
22、eliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90884 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event
23、of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individua
24、l item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual it
25、em requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein f
26、or device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance chara
27、cteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The ele
28、ctrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the ent
29、ire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking fo
30、r device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, app
31、endix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a m
32、anufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, th
33、e requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be
34、 provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Ve
35、rification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microci
36、rcuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 52 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5
37、962-90884 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C VIN= 17 V, IO= 1 A, Group A subgroups Device type Limits 1/ Unit COUT= 22 F unless otherwise specifi
38、ed Min Max Output voltage VOUTVIN= 17 V, IO= 5 mA 1 01 11.64 12.36 V 2,3 11.40 12.60 VIN= 13.6 V , IO= 5 mA 1 01 11.64 12.36 2, 3 11.40 12.60 VIN= 14 V, IO = 5 mA 1 01 11.64 12.36 2, 3 11.40 12.60 VIN= 26 V, IO= 5 mA 1 01 11.64 12.36 2, 3 11.40 12.60 VIN= 17 V, IO= 1 A 1 01 11.64 12.36 2, 3 11.40 12
39、.60 VIN= 13.6 V, IO= 1 A 1 01 11.64 12.36 2, 3 11.40 12.60 VIN= 13.6 V, IO= 50 mA 1 01 11.64 12.36 2, 3 11.40 12.60 VIN= 17 V, IO= 50 mA 1 01 11.64 12.36 2, 3 11.40 12.60 Maximum line transient VLTVO 13 V, 2/ RO= 100 , t = 20 ms 1, 2, 3 01 40 V Reverse polarity input voltage dc VRINRO= 100 2/ 1, 2,
40、3 01 -15 V Reverse polarity input voltage transient VRITRO= 100 , t = 20 ms 2/ 1, 2, 3 01 -45 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90884 DEFENSE SUPPLY CENTER COLUM
41、BUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C VIN= 17 V, IO= 1 A, Group A subgroups Device type Limits 1/ Unit COUT= 22 F unless otherwise specified Min Max Quiescent curren
42、t IQVIN= 17 V, IO= 5 mA 1 01 0 15 mA 2, 3 20 VIN= 14 V, IO= 5 mA 1 01 0 15 2, 3 20 VIN= 26 V, IO= 5 mA 1 01 0 15 2, 3 20 VIN= 17 V, IO= 1 A 1 01 0 50 2, 3 60 Line regulation VRLINE14 V VIN 26 V, 1 01 75 mV IO= 5 mA 2, 3 120 Load regulation VRLOADVIN= 17 V, 1 01 120 mV 50 mA IO 1 A 2, 3 190 Dropout v
43、oltage VDOIO= 1 A 1 01 0 0.7 V 2, 3 1 IO= 100 mA 1 0 200 mV 2, 3 300 Output noise voltage VONVIN= 17 V, IO= 5 mA , 10 Hz 100 kHz, TA= +25 C 2/ 1 01 0 1000 V rms Output impedance ROVIN= 17 V, 2/ IO= 100 mA dc and 20 mA ac, fO= 120 Hz 1, 2, 3 01 1 Short circuit current IOSVIN= 17 V 1 01 1.6 A 2, 3 1.3
44、 Ripple rejection RRVIN= 17 V, 1 Vrms, 4 01 52 dB f = 1 kHz, IO= 5 mA 5, 6 46 1/ The limiting terms “min” (minimum) and “max” (maximum) shall be considered to apply to magnitudes only. Negative current shall be defined as conventional current flow out of a device terminal. 2/ If not tested, shall be
45、 guaranteed to the limits specified in table I herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90884 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 7 DSCC FORM 2234 AP
46、R 97 Case outline M Symbol Inches Millimeters Min Max Min Max A .190 .210 4.83 5.33 b - .030 - 0.76 D .410 .430 10.41 10.92 D1 .580 .610 14.73 15.49 e - .100 - 2.54 e1 - .200 - 5.08 E .410 .420 10.41 10.67 L1 .090 .110 2.29 2.79 L .115 .125 2.92 3.18 N 3 3 NOTE: The U.S. government preferred system
47、of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reprod
48、uction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90884 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 8 DSCC FORM 2234 APR 97 Case outline U Symbol Inches Millimeters Min Max Min Max A .190 .200 4.83 5.08 A1 .035 .045 .89 1.14 A2 .120 BSC 3.05 BSC b .025 .035 .64 .89 D .645 .665 16.38 16.89 D1 .410 .430 10.41 10.92 D3 .000 .065 .00 1.65 e .100 BSC 2.54 BSC E .410 .422 10.41 10.71 L .500 .750 12
