1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with N.O.R. 5962-R075-93. 93-04-12 M. A. FRYE B Drawing updated to reflect current requirements. - ro 00-09-15 R. MONNIN C Five year review requirement. -rrp 08-03-18 R. HEBER THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEE
2、N REPLACED. REV SHET REV SHET REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY RICK C. OFFICER DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY CHARLES E. BESORE COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil TH
3、IS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, HIGH SPEED, PRECISION COMPARATOR WITH LATCH CIRCUIT, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 92-06-16 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-
4、91505 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E061-07 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91505 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 AP
5、R 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When
6、 available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 91505 01 M P X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator
7、(see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA le
8、vels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 AD790 High speed, precision comparator with latch circuit 1.2.3 Device cla
9、ss designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-3
10、8535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 1.2.5 Lead finish. The lead finish
11、 is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91505 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHI
12、O 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage single supply operation: Positive supply (+VS) . 7.0 V dc Negative supply (-VS) 0 V dc 2/ Logic supply (VLOGIC) . 7.0 V dc Supply voltage dual supply operation: Positive supply (+VS) . +18.0 V
13、 dc Negative supply (-VS) -18 V dc Logic supply (VLOGIC) . 7.0 V dc Differential input voltage (VDIFF) . 16.5 V dc Internal power dissipation (PD) . 500 mW Junction temperature (TJ) . +175C Storage temperature range . -65C to +150C Lead temperature (soldering, 60 seconds) +300C Thermal resistance, j
14、unction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA) +100C/W 1.4 Recommended operating conditions. Supply voltage single supply operation: Positive supply (+VS) .4.7 V dc to +7.0 V dc Negative supply (-VS) 0 V dc 2/ Logic supply (VLOGIC) .+4.2 V dc to +7.0 V dc Supply
15、 voltage dual supply operation: Positive supply (+VS) .+4.7 V dc to +16.5 V dc 3/ Negative supply (-VS) -4.7 dc to -16.5 V dc Logic supply (VLOGIC) .+4.2 V dc to +7.0 V dc Ambient operating temperature (TA) .-55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks
16、. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manu
17、facturing, General Specification for. 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ -VSmust not be connected above ground. 3/ +VSmust be no lower than VLOGIC 0.5 V in
18、 any supply operating conditions, except during power-up. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91505 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234
19、 APR 97 DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copie
20、s of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of thi
21、s drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classe
22、s Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M sh
23、all be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-
24、38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Block diagram(s). The block diagram(s) shall be as specified on figure 2
25、. 3.3 Electrical performance characteristics and post irradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and post irradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 E
26、lectrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. F
27、or packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accor
28、dance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “
29、C“ as required in MIL-PRF-38535, appendix A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91505 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE
30、 I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min MaxSingle supply operation 2/ Input offset voltage 3/ VOSSee figure 3 1 01 1.5 mV 2,3 2.0 Hysteresis 4/ VHSee figure 3 1,2,3 01 1.0 mV Input bi
31、as current IIBEither input 1 01 5.0 A 2,3 8.0 Input offset current IOS1 01 0.25 A 2,3 0.40 Power supply rejection ratio PSRR 4.0 V +VS 7.0 V 1 01 80 dB 2,3 76 Output high voltage VOHISOURCE= 6.4 mA 1,2,3 01 4.3 V Output low voltage VOLISINK= 6.4 mA 1,2,3 01 0.5 V LATCH input low voltage VIL1,2,3 01
32、0.8 LATCH input high voltage VIH1,2,3 01 1.6 V LATCH input current IIN1 01 5.0 A 2,3 8.0 Quiescent supply current IQ1 01 12 mA 2,3 16 Differential input voltage 5/ VDIFFTA= +25C 4 01 +VSV Common mode input 5/ voltage range VCMTA= +25C 4 01 0 +VS 2 V LATCH input setup 5/ time tSTA= +25C, see figure 4
33、 9 01 20 ns LATCH input hold 5/ time tHTA= +25C, see figure 4 9 01 35 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91505 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 4321
34、8-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min MaxSingle supply operation - continued 6/ Propagation delay time, 5/ input
35、 to output tPD100 mV step, 9 01 50 ns 5.0 mV overdrive, see figure 4 10,11 65 Dual supply operation 6/ Input offset voltage 3/ VOSSee figure 3 1 01 1.0 mV 2,3 1.5 Hysteresis 4/ VHSee figure 3 1,2,3 01 0.65 mV Input bias current IIBEither input 1 01 5.0 A 2,3 7.0 Input offset current IOS1 01 0.25 A 2
36、,3 0.40 Power supply rejection ratio PSRR +12 V +VS +18 V, -V = -15 V, 1 01 80 dB -12 V -VS -18 V, +V = +15 V, 2,3 76 Common mode rejection ratio CMRR -10 V VCM +10 V 1 01 80 dB 2,3 76 Output high voltage VOHISOURCE= 6.4 mA 1,2,3 01 4.3 V Output low voltage VOLISINK= 6.4 mA 1,2,3 01 0.5 V LATCH inpu
37、t low 5/ voltage VIL1,2,3 01 0.8 LATCH input high 5/ voltage VIH1,2,3 01 1.6 V LATCH input current 5/ IIN1 01 5.0 A 2,3 8.0 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91505
38、 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min MaxDual supply operatio
39、n 6/ Quiescent supply current +IQ1 01 10 mA 2,3 16 -IQ1 5.0 2,3 9.0 Logic supply current ILOGIC1 01 3.3 mA 2,3 4.5 Differential input voltage VDIFFTA= +25C, |VS| 15 V 1 01 VSV Common mode input 5/ voltage range +VCMTA= +25C, |VS| 15 V 4 01 +VS- 2 V -VCM-VSLATCH input setup 5/ time tSTA= +25C, see fi
40、gure 4 9 01 15 ns LATCH input hold 5/ time tHTA= +25C, see figure 4 9 01 35 ns Propagation delay 5/ time, input to output tPD100 mV step, 5.0 mV overdrive, 9 01 45 ns see figure 4 10,11 60 1/ The limiting terms “min” (minimum) and “max” (maximum) shall be considered to apply to magnitudes only. Nega
41、tive current shall be defined as conventional current flow out of a device terminal. 2/ Unless otherwise specified, +VS= VLOGIC= +5.0 V and VS= 0 V. All parameters tested with +VSpin tied to VLOGICpin and VSpin tied to GROUND pin. 3/ Defined as the average of the input voltages at the low to high an
42、d high to low transition points (see figure 3). 4/ Defined as half the magnitude between the input voltages at the low to high and high to low transition points (see figure 3). 5/ If not tested, shall be guaranteed to the limits specified in table I. 6/ Unless otherwise specified, +VS= +15 V, -VS= -
43、15 V, and VLOGIC= +5.0 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91505 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outl
44、ine P Terminal number Terminal symbol 1 +VS2 +INPUT 3 -INPUT 4 -VS5 LATCH 6 GROUND 7 OUTPUT 8 VLOGICFIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91505 DEFENSE SUPPLY CENTER
45、COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 FIGURE 2. Block diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91505 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 4
46、3218-3990 REVISION LEVEL C SHEET 10 DSCC FORM 2234 APR 97 NOTES: VH= Hysteresis voltage and VOS= Input offset voltage. FIGURE 3. Hysteresis. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91505 DEFENSE SUPPL
47、Y CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 11 DSCC FORM 2234 APR 97 NOTES: tS= Setup time, tH= Hold time, and tPD= Comparator response time. FIGURE 4. Timing diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91505 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 12 DSCC FORM 2234 APR 97 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be requir
