1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes IAW NOR 5962-R023-97 tvn. 96-10-17 Monica L. Poelking B Redrawn with changes. Update the boilerplate to the current requirements of MIL-PRF-38535. - jak 08-05-13 Thomas M. Hess REV SHEET REV B B B B B SHEET 15 16 17 18 19 REV STATUS REV B
2、 B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Joseph A. Kerby STANDARD MICROCIRCUIT DRAWING CHECKED BY Thanh V. Nguyen DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMEN
3、TS APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, FAST CMOS, 16-BIT BIDIRECTIONAL TRANSCEIVER WITH THREE-STATE OUTPUTS, TTL COMPATIBLE INPUTS, AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-03-22 LIMITED OUTPUT VOLTAGE SWING, MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SI
4、ZE A CAGE CODE 67268 5962-92258 SHEET 1 OF 19 DSCC FORM 2233 APR 97 5962-E320-08 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92258 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B
5、 SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Iden
6、tifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 92258 01 M X A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorC
7、ase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, app
8、endix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54FCT16245T 16-bit bidirectional transceiver with
9、three-state outputs, TTL compatible inputs and limited output voltage swing 02 54FCT16245AT 16-bit bidirectional transceiver with three-state outputs, TTL compatible inputs and limited output voltage swing 03 54FCT16245CT 16-bit bidirectional transceiver with three-state outputs, TTL compatible inpu
10、ts and limited output voltage swing 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN clas
11、s level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X GDFP1-F48 48 Flat
12、pack 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92258 DEFEN
13、SE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to VCC+ 0.5 V dc 4/ DC output voltage range (VOUT) . -0.5 V dc to VCC+ 0.
14、5 V dc 4/ Input clamp current (IIK) (VIN= -0.5V). -20 mA Output clamp current (IOK) (VOUT= -0.5V and+7.0 V) 20 mA DC output source current (IOH) per output -30 mA DC output sink current (IOL) per output. +70 mA DC VCCcurrent (ICC). 480 mA DC ground current (IGND) 1120 mA Storage temperature range (T
15、STG) . -65C to +150C Case temperature under bias (TBIAS) . -65C to +135C Maximum power dissipation (PD) . 1.0 W Lead temperature (soldering, 10 seconds). +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions. 2/ 3/ Sup
16、ply voltage range (VCC) +4.5 V dc to +5.5 V dc Input voltage range (VIN) +0.0 V dc to VCCOutput voltage range (VOUT). +0.0 V dc to VCCMaximum low level input voltage(VIL). 0.8 V Maximum high level input voltage (VIH) 2.0 V Case operating temperature range (TC). -55C to +125C Maximum input rise or fa
17、ll rate (t/V): (from VIN= 0.3 V to 2.7 V, 2.7 V to 0.3 V) 2.5 ns/V Maximum high level output current (IOH) -24 mA Maximum low level output current (IOL) 48 mA 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade
18、performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. 4/ For VCC 6.5 V, the upper limit on the range is limited to
19、7.0 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92258 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government spec
20、ification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Stan
21、dards (DoDISS) and supplement thereto, cited in the solicitation. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Ele
22、ctronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or from the Standard
23、ization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws an
24、d regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. T
25、he modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. This drawing has been modified to allow
26、 the manufacturer to use the alternate die/fabrication requirements of paragraph A.3.2.2 of MIL-PRF-38535 or other alternative approved by the Qualifying Activity. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38
27、535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth
28、table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce load circuit and waveforms. The ground bounce load circuit and waveforms shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching
29、 waveforms and test circuit shall be as specified on figure 5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92258 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM
30、 2234 APR 97 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range.
31、 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be mar
32、ked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in
33、 accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall
34、be a “C“ as required in MIL-PRF-38535, appendix A. For class Q product built in accordance with A.3.2.2 of MIL-PRF-38535 or other alternative approved by the Qualifying Activity, the “QD” certification mark shall be used in place of the “QML” or “Q” certification mark. 3.6 Certificate of compliance.
35、 For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an
36、 approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and her
37、ein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuit
38、s delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affect this drawing. 3.9 Verification and review for device class M
39、. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class
40、M. Device class M devices covered by this drawing shall be in microcircuit group number 37 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92258 DEFENSE SUPPLY CENTER COLUMBUS
41、 COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits 3/ Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified Devicetype VCCGroup A subgroups Min Max Unit V
42、OH14/ For all inputs affecting output under test, VIN= VIHor VILVIH= 2.0 V, VIL= 0.8 V For all other inputs VIN= VCCor GND IOH= -300 A All 4.5 V 1, 2, 3 3.0 VCC-0.5VOH2For all inputs affecting output under test, VIN= VIHor VILVIH= 2.0 V, VIL= 0.8 V For all other inputs VIN= VCCor GND IOH= -3 mA All
43、4.5 V 1, 2, 3 2.5 VCC-0.5V VOH34/ For all inputs affecting output under test, VIN= VIHor VILVIH= 2.0 V, VIL= 0.8 V For all other inputs VIN= VCCor GND IOH= -12 mA All 4.5 V 1, 2, 3 2.4 VCC-0.5High level output voltage 3006 VOH4For all inputs affecting output under test, VIN= VIHor VILVIH= 2.0 V, VIL
44、= 0.8 V For all other inputs VIN= VCCor GND IOH= -24 mA All 4.5 V 1, 2, 3 2.0 VCC-0.5V VOL14/ For all inputs affecting output under test, VIN= VIHor VILVIH= 2.0 V, VIL= 0.8 V For all other inputs VIN= VCCor GND IOL= 300 A 4.5 V 1, 2, 3 0.20 V Low level output voltage 3007 VOL2For all inputs affectin
45、g output under test, VIN= VIHor VILVIH= 2.0 V, VIL= 0.8 V For all other inputs VIN= VCCor GND IOL= 48 mA All 4.5 V 1, 2, 3 0.55 1, 2 1.0 Three-state output current high 3021 IOZH5/ 6/ mOE = VIHor VILVIH= 2.0 V, VIL= 0.8 V For all other inputs, VIN= VCCor GND VOUT= VCCAll 5.5 V 3 5.0 A See footnotes
46、at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92258 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance c
47、haracteristics Continued. Limits 3/ Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified Device type VCCGroup A subgroups Min Max Unit 1, 2 1.0 Three-state output current low 3021 IOZL5/ 6/ mOE = VIHor VILVIH= 2.0 V, VIL= 0.8 V For
48、all other inputs, VIN= VCCor GND VOUT= GND All 5.5 V 3 5.0 A Negative input clamp voltage 3022 VIC-For input under test, IIN= -18 mA All 4.5 V 1, 2, 3 -1.2 V 1, 2 1.0 control inputs 3 5.0 A 1, 2 1.0 Input current high 3010 IIHFor input under test VIN= VCCFor all other inputs VIN= VCCor GND I/O Pins All 5.5 V 3 5.0 A 1, 2 1.0 control inputs 3 5.0 A 1, 2 1.0 Input current low 3009 IILFor input under test VIN= GND For all other inputs VIN= VCCor GND I/O Pins All 5.5 V 3 5.0 A Input capacitance 3012 CIN7/ See 4.4.1c TC= +25 All GND 4 6.0 pF Input output capacitance 30
