1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Case outline X change dimension D and dimension L max. Update boilerplate. 97-07-03 R. MONNIN B Case outline “X” dimensions L, R, and R1 are updated. rrp 97-12-02 R. MONNIN C Replaced reference to MIL-STD-973 with reference to MIL-PRF-38535. Repl
2、aced figure 1 with reference to standard figure in MIL-STD-1835. - gt 03-09-03 R. MONNIN D Update boilerplate paragraphs. - ro 09-09-08 C. SAFFLE REV SHET REV SHET REV STATUS REV D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RAJESH PITHADIA DEFENSE SUPPLY CENTER
3、COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAJESH PITHADIA APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, CMOS, PRECISION, DUAL/QUAD, MICROPOWER,
4、OPERATIONAL AMPLIFIER, MONOLITHIC SILICON DRAWING APPROVAL DATE 96-04-25 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-95603 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E473-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUI
5、T DRAWING SIZE A 5962-95603 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device clas
6、s V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 95603 01 Q C A Feder
7、al stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked
8、 with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows
9、: Device type Generic number Circuit function 01 LMC6462A Precision CMOS dual micropower operational amplifier 02 LMC6464A Precision CMOS quad micropower operational amplifier 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as fol
10、lows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case out
11、line(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line P GDIP1-T8 or CDIP2-T8 8 Dual-in-line X GDFP1-G14 14 Flat pack with gullwing leads 1.2.5 Lead finish. The lead finish is as specified in MI
12、L-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95603 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION
13、LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (V+ - V-) 16 V Differential input voltage . Supply voltage Voltage at input/output pin (V+) + 0.3 V, (V-) 0.3 V Current at input pin . 5 mA 2/ Current at output pin . 30 mA 3/ 4/ Current at power supply pin 40 mA S
14、torage temperature range . -65C to +150C Maximum power dissipation (PD): Device type 01 3 mW Device type 02 6 mW Lead temperature (soldering, 10 seconds) +260C Junction temperature (TJ) . +150C 3/ Thermal resistance, junction-to-case (JC): 5/ Case outlines C and X 8C/W Case outline P . 14C/W Thermal
15、 resistance, junction-to-ambient (JA): 5/ Case outline C . 74C/W still air 37C/W 500 LFPM Case outline P . 122C/W still air 67C/W 500 LFPM Case outline X . 132C/W still air 78C/W 500 LFPM 1.4 Recommended operating conditions. Supply voltage +3.0 V to +15.5 V Ambient operating temperature range (TA)
16、. -55C to +125C _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Limiting input pin current is only necessary for input voltages that exceed absolute maximum input vol
17、tage ratings. 3/ Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150C. Output currents in excess of 30 mA over long term may adversely affect reliability. Both single-supply and split-supply operation are affected
18、. 4/ Must not connect output to V+ when V+ is greater than 13 V or reliability will be adversely affected. 5/ Thermal resistance limits apply for packages soldered directly into a printed circuit board. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,
19、-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95603 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part o
20、f this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS
21、 MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available onli
22、ne at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing
23、takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified
24、 herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN clas
25、s level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines
26、. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance charact
27、eristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are def
28、ined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-
29、“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certi
30、fication mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MI
31、CROCIRCUIT DRAWING SIZE A 5962-95603 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit M
32、in Max 3 Volt parameters Input offset voltage VOS1 All 0.8 mV 2,3 1.7 Input bias current IBIAS2/ 1 All 25 pA 2,3 100 Input offset current IOS2/ 1 All 25 pA 2,3 100 Common mode rejection ratio CMRR 0 V VCM 3.0 V 1 All 60 dB 2,3 57 Input common-mode voltage range VCMCMRR 50 dB 1 All 3.0 0.0 V 2,3 2.9
33、0.1 Supply current ICCVO= V+/2 1 01 55 A 2,3 70 1 02 110 2,3 140 Output short circuit current ISCSourcing, VO= 0 V 1 All 8 mA 2,3 6 Sinking, VO= 3 V 1 All 23 2,3 17 Output voltage swing VOPRL= 25 k to V+/2 1 All 2.9 0.10 V 2,3 2.8 0.15 5 Volt parameters Input offset voltage VOS1 All 0.5 mV 2,3 1.4 I
34、nput bias current IBIAS2/ 1 All 25 pA 2,3 100 Input offset current IOS2/ 1 All 25 pA 2,3 100 Common mode rejection ratio CMRR 0 V VCM 5.0 V 1 All 70 dB 2,3 67 Input common-mode voltage range VCMCMRR 50 dB 1 All 5.25 -0.10 V 2,3 5.00 0.00 See footnotes at end of table. Provided by IHSNot for ResaleNo
35、 reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95603 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions
36、 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max 5 Volt parameters continued. Supply current ICCVO= V+/2 1 01 55 A 2,3 70 1 02 110 2,3 140 Output short circuit current ISCSourcing, VO= 0 V 1 All 19 mA 2,3 15 Sinking, VO= 5 V 1 22 2,3 17 Output voltage sw
37、ing VOPRL= 100 k to V+/2 1 All 4.990 0.010 V 2,3 4.980 0.020 RL= 25 k to V+/2 1 4.975 0.020 2,3 4.965 0.035 15 Volt parameters Input offset voltage VOS1 All 1.8 mV 2,3 2.3 Input bias current IBIAS2/ 1 All 25 pA 2,3 100 Input offset current IOS2/ 1 All 25 pA 2,3 100 Common mode rejection ratio CMRR 0
38、 V VCM 15.0 V 1 All 70 dB 2,3 67 Input common-mode voltage range VCMCMRR 50 dB 1 All 15.25 -0.15 V 2,3 15.00 0.00 Positive power supply rejection ratio +PSRR 5 V V+ 15.0 V, V- = 0 V, VO= 2.5 V 1 All 70 dB 2,3 67Negative power supply rejection ratio -PSRR -5 V V- -15.0 V, V+ = 0 V, VO= -2.5 V 1 All 7
39、0 dB 2,3 67Output voltage swing VOPRL= 100 k to V+/2 1 All 14.975 0.025 V 2,3 14.965 0.035 RL= 25 k to V+/2 1 14.900 0.050 2,3 14.850 0.150 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING S
40、IZE A 5962-95603 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max 15
41、Volt parameters continued. Supply current ICCVO= V+/2 1 01 60 A 2,3 70 1 02 120 2,3 140 Output short circuit current ISCSourcing, VO= 0 V 1 All 24 mA 2,3 17 Sinking, VO= 12 V 3/ 1 All 55 2,3 45 Large signal voltage gain AVSourcing, RL= 100 k 4/ 1 All 110 dB 2,3 80 Sinking, RL= 100 k 4/ 1 100 2,3 70
42、Sourcing, RL= 25 k 4/ 1 110 2,3 70 Sinking, RL= 25 k 4/ 1 95 2,3 60 Slew rate SR5/ 4 All 15 V/ms 5,6 7 Gain-bandwidth GBW4 All 60 kHz 5,6 45 1/ Unless otherwise specified, V+ = 3 V, 5 V or 15 V, V- = 0 V, VCM= VO= V+/2, RL 1 M. 2/ Limits are dictated by testing limitations and not device performance
43、. 3/ Do not short circuit output to V+ when V+ is greater than 13 V as reliability will be adversely affected. 4/ VCM= 7.5 V, RL= connected to 7.5 V. For sourcing tests, 7.5 V VO 11.5 V and for sinking tests, 3.5 V VO 7.5 V. 5/ Device configured as a voltage follower, with a 10 V input step. For pos
44、itive slew, VINswing is 2.5 V to 12.5 V, VOUTis measured between 6.0 V and 9.0 V. For negative slew, VINswing is 12.5 V to 2.5 V, VOUTis measured between 9.0 V and 6.0 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING S
45、IZE A 5962-95603 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 Device types 01 02 Case outlines P C and X Terminal number Terminal symbol 1 OUTPUT 1 OUTPUT 1 2 IN 1- IN 1- 3 IN 1+ IN 1+ 4 V- V+ 5 IN 2+ IN 2+ 6 IN 2- IN 2- 7 OUTPUT 2 OUTPUT 2
46、8 V+ OUTPUT 3 9 - IN 3- 10 - IN 3+ 11 - V- 12 - IN 4+ 13 - IN 4- 14 - OUTPUT 4 FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95603 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OH
47、IO 43218-3990 REVISION LEVEL D SHEET 9 DSCC FORM 2234 APR 97 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a
48、certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the r
