1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationSafety of woodworking machines Circular sawing machinesPart 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloadingBS E
2、N 1870-8:2012National forewordThis British Standard is the UK implementation of EN 1870-8:2012. It super-sedes BS EN 1870-8:2001+A1:2009 which is withdrawn.The UK participation in its preparation was entrusted to Technical CommitteeMTE/23, Woodworking machines.A list of organizations represented on
3、this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012ISBN 978 0 580 72425 1ICS
4、79.120.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 31 January 2013.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 1870-8
5、:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1870-8 November 2012 ICS 79.120.10 Supersedes EN 1870-8:2001+A1:2009English Version Safety of woodworking machines - Circular sawing machines - Part 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loa
6、ding and/or unloading Scurit des machines pour le travail du bois - Machines scies circulaires - Partie 8: Dligneuses mono-lames dplacement mcanis du groupe de sciage et chargement et/ou dchargement manuel Sicherheit von Holzbearbeitungsmaschinen - Kreissgemaschinen - Teil 8: Einblattbesum- und Leis
7、tenkreissgemaschinen mit kraftbettigtem Sgeaggregat und Handbeschickung und/oder Handentnahme This European Standard was approved by CEN on 1 September 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the
8、 status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, Frenc
9、h, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria,
10、Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey a
11、nd United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1870-
12、8:2012: EBS EN 1870-8:2012EN 1870-8:2012 (E) 2 Contents Page Foreword 4Introduction .61 Scope 72 Normative references 73 Terms and definitions .94 List of significant hazards . 135 Safety requirements and/or measures . 165.1 General . 165.2 Controls . 165.2.1 Safety and reliability of control system
13、s 165.2.2 Position of controls 175.2.3 Starting 175.2.4 Normal stopping . 185.2.5 Emergency stop 195.2.6 Integrated feed 195.2.7 Saw blade changing . 205.2.8 Speed control 205.2.9 Control duplication . 205.2.10 Failure of the power supply . 205.2.11 Powered movement of the saw blade and/or fences 21
14、5.3 Protection against mechanical hazards . 225.3.1 Stability 225.3.2 Risk of break-up during operation 225.3.3 Tool holder and tool design . 235.3.4 Braking . 245.3.5 Devices to minimise the possibility or the effect of ejection . 255.3.6 Workpiece supports and guides . 305.3.7 Prevention of access
15、 to moving parts 315.3.8 Workpiece clamping . 335.3.9 Safety appliances 355.4 Protection against non-mechanical hazards . 355.4.1 Fire . 355.4.2 Noise 355.4.3 Emission of chips and dust . 365.4.4 Electricity . 375.4.5 Ergonomics and handling 375.4.6 Lighting 385.4.7 Pneumatic 385.4.8 Hydraulic 385.4
16、.9 Electromagnetic compatibility . 385.4.10 Laser 385.4.11 Errors of fitting 395.4.12 Isolation . 395.4.13 Maintenance 396 Information for use . 406.1 General . 406.2 Warnings and warning devices . 406.3 Marking 40BS EN 1870-8:2012EN 1870-8:2012 (E) 3 6.3.1 Marking of riving knives . 406.3.2 Marking
17、 of machine . 406.4 Instruction handbook 41Annex A (normative) Saw spindle dimensional tolerances 45Annex B (normative) Riving knife mounting strength test . 46Annex C (normative) Lateral stability riving knife test . 47Annex D (normative) Sectional safety curtain material rigidity test 48Annex E (n
18、ormative) Operating conditions for noise emission measurement 49E.1 General . 49E.2 Noise measurements 49E.3 General data sheet 51Annex F (normative) Braking tests . 55F.1 Conditions for all tests 55F.2 Tests . 55F.2.1 Un-braked run-down time . 55F.2.2 Braked run-down time . 55Annex G (normative) Im
19、pact test method for guards . 56G.1 General . 56G.2 Test method . 56G.2.1 Preliminary remarks 56G.2.2 Testing equipment . 56G.2.3 Projectile for guards 56G.2.4 Sampling. 56G.2.5 Test procedure . 56G.3 Results 57G.4 Assessment . 57G.5 Test report 57G.6 Test equipment for impact test 57Annex ZA (infor
20、mative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC 59Bibliography 60BS EN 1870-8:2012EN 1870-8:2012 (E) 4 Foreword This document (EN 1870-8:2012) has been prepared by Technical Committee CEN/TC 142 “Woodworking machines - Safety”, the secret
21、ariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2013, and conflicting national standards shall be withdrawn at the latest by May 2013. Attention is drawn to the
22、possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1870-8:2001+A1:2009. This document has been prepared under a mandate given to CEN by
23、 the European Commission and the European Free Trade Association, and supports essential requirements of the Machinery Directive. For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. The main modifications to the previous version concern inclus
24、ion of performance levels (PL). Organisations contributing to the preparation of this European Standard include European Committee of Woodworking Machinery Manufacturers Association “EUMABOIS“. EN 1870 Safety of woodworking machines Circular sawing machines consists of the following parts: Part 1: C
25、ircular saw benches (with and without sliding table), dimension saws and building site saws; Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches; Part 4: Multiblade rip sawing machines with manual loading and/or unloading; Part 5: Circular sawbenches
26、/up-cutting cross-cut sawing machines; Part 6: Circular sawing machines for firewood and dual purpose circular sawing machines for firewood/circular saw benches, with manual loading and/or unloading; Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unload
27、ing; Part 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading (the present document); Part 9: Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading; Part 10: Single blade au
28、tomatic and semi-automatic up-cutting cross-cut sawing machines; Part 11: Semi-automatic and automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws); Part 12: Pendulum cross-cut sawing machines; Part 13: Horizontal beam panel sawing machines; BS EN 1870-8:2012EN 1870-8:201
29、2 (E) 5 Part 14: Vertical panel sawing machines; Part 15: Multi-blade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading; Part 16: Double mitre sawing machines for V-cutting; Part 17: Manual horizontal cutting cross-cut sawing machines with one saw un
30、it (manual radial arm saws); Part 18: Dimension saws (at Formal Vote stage at the time of publication of the present document); Part 19: Circular saw benches (with and without sliding table) and building site saws (at Enquiry stage at the time of publication of the present document). The European St
31、andards produced by CEN/TC 142 are particular to woodworking machines and complement the relevant A and B Standards on the subject of general safety (see Introduction of EN ISO 12100:2010 for a description of A, B and C standards). According to the CEN/CENELEC Internal Regulations, the national stan
32、dards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, L
33、uxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 1870-8:2012EN 1870-8:2012 (E) 6 Introduction This document has been prepared to be a harmonised standard to provide one means of conforming to the es
34、sential safety requirements of the Machinery Directive, and associated EFTA regulations. This document is a type “C” standard as defined in EN ISO 12100:2010. The machinery concerned and the extent to which hazards, hazardous situations and events covered are indicated in the scope of this document.
35、 The requirements of this document are directed to manufacturers and their authorised representatives of single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading. This document is also useful for designers and importers. When provisions of this
36、type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of other standards, for machines that have been designed and built according to the provisions of this type C standard. This document also in
37、cludes information to be provided by the manufacturer to the user. Common requirements for tooling are given in EN 847-1:2005+A1:2007. BS EN 1870-8:2012EN 1870-8:2012 (E) 7 1 Scope This European Standard deals with all significant hazards, hazardous situations and events as listed in Clause 4 which
38、are relevant to single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading, hereinafter referred to as “machines”, designed to cut solid wood, chipboard, fibreboard and plywood when they are used as intended and under the conditions foreseen by th
39、e manufacturer including reasonably foreseeable misuse. This document applies to machines where the workpiece is stationary, the vertical and horizontal movements of the saw unit are power driven, and where the machine is provided with workpiece clamping. The workpiece may or may not be clamped duri
40、ng cutting. This document does not apply to machines: where the workpiece is fed to the saw blade during cutting; designed for cutting veneers; provided with a device situated behind the line of cut, which moves in a direction parallel to the line of cut, for automatically unloading the workpiece du
41、ring the return of the saw unit to the rest position. This document is not applicable to machines manufactured before its date of publication as EN. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its applicat
42、ion. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 349:1993+A1:2008, Safety of machinery Minimum gaps to avoid crushing of parts of the human body EN 614-1:2006+A1:2009, Safety of mac
43、hinery Ergonomic design principles Part 1: Terminology and general principles EN 614-2:2000+A1:2008, Safety of machinery Ergonomic design principles Part 2: Interactions between the design of machinery and work tasks EN 847-1:2005+A1:2007, Tools for woodworking Safety requirements Part 1: Milling to
44、ols, circular saw blades EN 894-1:1997+A1:2008, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 1: General principles for human interactions with displays and control actuators EN 894-2:1997+A1:2008, Safety of machinery Ergonomics requirements for th
45、e design of displays and control actuators Part 2: Displays EN 894-3:2000+A1:2008, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 3: Control actuators EN 1005-1:2001+A1:2008, Safety of machinery Human physical performance Part 1: Terms and definitio
46、ns EN 1005-2:2003+A1:2008, Safety of machinery Human physical performance Part 2: Manual handling of machinery and component parts of machinery BS EN 1870-8:2012EN 1870-8:2012 (E) 8 EN 1005-3:2002+A1:2008, Safety of machinery Human physical performance Part 3: Recommended force limits for machinery
47、operation EN 1005-4:2005+A1:2008, Safety of machinery Human physical performance Part 4: Evaluation of working postures and movements in relation to machinery EN 1037:1995+A1:2008, Safety of machinery Prevention of unexpected start-up EN 1088:1995+A2:2008, Safety of machinery Interlocking devices as
48、sociated with guards Principles for design and selection EN 1837:1999+A1:2009, Safety of machinery Integral lighting of machines EN 12779:2004+A1:2009, Safety of woodworking machines Chip and dust extraction systems with fixed installation Safety related performances and safety requirements EN 50370-1:2005, Electromagnetic compatibility (EMC) Product family standard for machine tools Part 1: Emission EN 50370-2:2003, Electromagnetic compatibility (EMC)
