1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 15819:2011Polymer modifiedbituminous thick coatings forwaterproofing Reduction ofthe thickness of the layer whenfully driedBS EN 15819:2011 BRITISH STANDARDNational forewor
2、dThis British Standard is the UK implementation of EN 15819:2011. The UK participation in its preparation was entrusted to TechnicalCommittee B/546, Flexible sheets for waterproofing and water vapour control.A list of organizations represented on this committee can be obtained on request to its secr
3、etary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 62270 0 ICS 91.100.50 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was p
4、ublished under the authority of the Standards Policy and Strategy Committee on 31 August 2011.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 15819:2011EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15819 March 2011 ICS 91.100.50 English Version Polymer modified bituminous
5、 thick coatings for waterproofing - Reduction of the thickness of the layer when fully dried Revtements bitumineux pais modifis aux polymres pour impermabilisation - Rduction de lpaisseur de la couche lorsquelle est totalement sche Kunststoffmodifizierte Bitumendickbeschichtungen zur Bauwerksabdicht
6、ung - Verringerung der Schichtdicke nach dem Austrocknen This European Standard was approved by CEN on 13 February 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard withou
7、t any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other la
8、nguage made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denm
9、ark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISA
10、TION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15819:2011: EBS EN 15819:2011EN 15819:2011 (E) 2 Contents Page Foreword 31 Scope 42 Norma
11、tive references 43 Terms and definitions .44 Principle 45 Apparatus .46 Test specimens 47 Preparation .58 Procedure .58.1 Test conditions 58.2 Procedure .59 Expression of results and precision 59.1 Expression of results 59.2 Precision .510 Test report 6BS EN 15819:2011EN 15819:2011 (E) 3 Foreword Th
12、is document (EN 15819:2011) has been prepared by Technical Committee CEN/TC 361 “Project Committee Polymer modified bituminous thick coatings for waterproofing Definitions/requirements and test methods”, the secretariat of which is held by DIN. This European Standard shall be given the status of a n
13、ational standard, either by publication of an identical text or by endorsement, at the latest by September 2011, and conflicting national standards shall be withdrawn at the latest by September 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject
14、of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgar
15、ia, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 15819:2011EN 15819
16、:2011 (E) 4 1 Scope This European Standard specifies a procedure for determining the reduction in the thickness of polymer modified bituminous thick coatings due to drying for waterproofing. 2 Normative references The following referenced documents are indispensable for the application of this docum
17、ent. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1426, Bitumen and bituminous binders Determination of needle penetration FprEN 15814:2011, Polymer modified bituminous thick coating
18、s for waterproofing Definitions and requirements ISO 554, Standard atmospheres for conditioning and/or testing Specifications 3 Terms and definitions For the purposes of this document, the terms and definitions given in FprEN 15814:2011 apply. 4 Principle The reduction of thickness of polymer modifi
19、ed bitumen emulsion is the difference between measuring of wet and dry layer thickness under special conditions on a coated surface. 5 Apparatus 5.1 Stiff metal or glass plate with the following minimum dimensions: 25 cm 25 cm. 5.2 Plastic or metal frame with a height of 5 mm and inside dimensions o
20、f 15 cm 20 cm. 5.3 Palette knife, smoothing trowel, mixing equipment. 5.4 Instrument for measuring the thickness of the wet layer, e.g. penetrometer as described in EN 1426. 5.5 Suitable instrument for measuring the thickness of the dry layer, e.g. sliding calliper or inductive measuring instrument.
21、 6 Test specimens Test specimen with dimensions of 200 mm 150 mm 5 mm. BS EN 15819:2011EN 15819:2011 (E) 5 7 Preparation The ready-to-use bitumen coating shall be prepared in accordance with the manufacturers instructions. In case of a two component emulsion, mix the bitumen emulsion (component A) a
22、nd cement (component B), using a low-speed mixer setting to avoid entrapping any air. Fasten the frame to the degreased metal or glass plate and place it on a horizontal surface. Fill the frame up to the top with the mixed coating, taking care not to entrap any air. Strike off the top of the coating
23、 with the smoothing trowel so that it is level with the top of the frame. 8 Procedure 8.1 Test conditions The test shall be carried out at a temperature of (23 2) C. 8.2 Procedure Determine the thickness of the wet layer immediately after preparation of the specimens. NOTE A penetrometer as describe
24、d in EN 1426 is suitable for this purpose. The frame shall remain in place to prevent the fresh specimen spreading outwards. Measure the wet thickness to 0,1 mm at five equally spaced points in each third of the specimen but at a distance of not less than around 1 cm from the edges. Clean the test i
25、nstrument (e.g. the point of the needle of the penetrometer) prior to each measurement to avoid measuring errors. The thickness of the wet layer (dna) is the mean value of the 15 results, rounded to 0,1 mm. After the thickness of the wet layer has been measured, carefully remove the frame and store
26、the specimen in a horizontal position in a normal climate of (23 2) C and a relative humidity of (50 5) % in accordance with ISO 554 for 28 days (dtr). ()100/natrnaD= ddd % After conditioning, measure the dry thickness of the layer. The thickness of the dry layer shall be measured using vernier call
27、ipers permitting a reading to 0,1 mm. 12 readings shall be taken. The highest and lowest values shall be ignored and the mean value calculated from the remaining 10 values. 9 Expression of results and precision 9.1 Expression of results The test result is the reduction in the thickness of the layer
28、(D) in relation to the thickness of the wet layer, expressed as a percentage. 9.2 Precision Precision data are currently not available. BS EN 15819:2011EN 15819:2011 (E) 6 10 Test report The test report shall include at least the following information: a) all details necessary to identify the produc
29、t tested; b) a reference to this European Standard (i.e. EN 15819) and any deviation from it; c) details of preparation of test specimens in accordance with Clause 7; d) test procedure including: specimen thickness (wet/dry and reduction in %); deviation of test conditions; e) the test results in ac
30、cordance with Clause 9; f) the dates of the tests. This page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the internatio
31、nal level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make
32、 sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee resp
33、onsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (
34、0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax:
35、+44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand in
36、ternational standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Member
37、s are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British S
38、tandards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright,
39、 Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the standa
40、rd of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email:
