1、BSI Standards PublicationSpecification for radio disturbance and immunity measuring apparatus and methodsPart 2-3: Methods of measurement of disturbances and immunity Radiated disturbance measurementsBS EN 55016-2-3:2010+A1:2010BS EN 55016-2-3:2010+A2:2014Incorporating corrigendum September 2013BS E
2、N 55016-2-3:2010+A2:2014National forewordThis British Standard is the UK implementation of EN 55016-2-3:2010+A2:2014. It is identical to CISPR 16-2-3:2010, incorporating amendments 1:2010 and 2:2014. It supersedes BS EN 55016-2-3:2010+A1:2010, which will be withdrawn on 18 April 2017.BSI as a member
3、 of CENELEC, is obliged to publish the second amendment to EN 55016-2-3:2010+A2 as a British Standard. However, attention is drawn to the fact that during the development of this European Standard, the UK committee voted against its approval as a European Standard. The concern in amendment 2 clause
4、7.3.6.3 is that it does not provide a representative simulation of mains cabling. The UK will continue to work to improve this standard and its application to dependent standards. Technical justification was presented at the Tokyo EMC conference in May 2014 in the paper: ”Measurement Method, Uncerta
5、inty and Cable Balance - with Implications for the CDNE-M” by D M Lauder 33.100.20Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2011.Amendments/corrigen
6、da issued since publicationDate Text affected30 June 2011 Implementation of CISPR Amendment 1:2010 with CENELEC endorsement A1:201030 September 2013 Supersession information removed from EN title page30 September 2014 Implementation of CISPR amendment 2:2014 with CENELEC endorsement A2:2014BRITISH S
7、TANDARDEUROPEAN STANDARD EN 55016-2-3NORME EUROPENNE EUROPISCHE NORM CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2010 CENELEC -
8、All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 55016-2-3:2010 E ICS 33.100.10; 33.100.20 Supersedes EN 55016-2-3:2006English version Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-3: Methods of me
9、asurement of disturbances and immunity - Radiated disturbance measurements (CISPR 16-2-3:2010) Spcifications des mthodes et des appareils de mesure des perturbations radiolectriques et de limmunit aux perturbations radiolectriques - Partie 2-3: Mthodes de mesure des perturbations et de limmunit - Me
10、sures des perturbations rayonnes (CISPR 16-2-3:2010) Anforderungen an Gerte und Einrichtungen sowie Festlegung der Verfahren zur Messung der hochfrequenten Straussendung (Funkstrungen) und Strfestigkeit - Teil 2-3: Verfahren zur Messung der hochfrequenten Straussendung (Funkstrungen) und Strfestigke
11、it - Messung der gestrahlten Straussendung(CISPR 16-2-3:2010) This European Standard was approved by CENELEC on 2010-06-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard
12、 without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other l
13、anguage made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech
14、Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. :2010+A2 June 2014 Foreword The text of doc
15、ument CISPR/A/886/FDIS, future edition 3 of CISPR 16-2-3, prepared by CISPR SC A, Radio-interference measurements and statistical methods, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 55016-2-3 on 2010-06-01. This European Standard supersedes EN 55016-2-3:2006. Th
16、is EN 55016-2-3:2010 includes the following significant technical changes with respect to EN 55016-2-3:2006: addition of the measurand for radiated emissions measurements in an OATS and a SAC in the range of 30 MHz to 1 000 MHz, and addition of a new normative annex on the determination of suitabili
17、ty of spectrum analysers for compliance tests. Also, numerous maintenance items are addressed to make the standard current with respect to other parts of the EN 55016 series. It has the status of a basic EMC publication in accordance with IEC Guide 107, Electromagnetic compatibility Guide to the dra
18、fting of electromagnetic compatibility publications. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: late
19、st date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2011-03-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2013-06-01 Annex ZA has been added by CENELEC. _ Endorsem
20、ent notice The text of the International Standard CISPR 16-2-3:2010 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: 1 CISPR 11:2009 NOTE Harmonized as EN 55011:2009 (
21、modified). 3 CISPR 22:2008 NOTE Harmonized as EN 55022:200X 1)(modified). 4 IEC 61140:2001 NOTE Harmonized as EN 61140:2002 (not modified). 6 ISO/IEC 17000:2004 NOTE Harmonized as EN ISO/IEC 17000:2004 (not modified). 7 IEC 61000-4-21 NOTE Harmonized as EN 61000-4-21. _ 1)At draft stage.Foreword to
22、amendment A1 The text of document CISPR/A/878/CDV, future amendment 1 to CISPR 16-2-3:2010, prepared by CISPR SC A, Radio-interference measurements and statistical methods, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 55016-2-3:2010 on 2010-10-01.
23、Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent rights. The following dates were fixed: latest date by which the amendment has to be implemented
24、at national level by publication of an identical national standard or by endorsement (dop) 2011-07-01 latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2013-10-01 _ Endorsement notice The text of amendment 1:2010 to the International Standard IEC 5
25、5016-2-3:2010 was approved by CENELEC as an amendment to the European Standard without any modification. _ 2 BS EN 55016-2-3:2010+A2:2014 EN 55016-2-3:2010+A2:2014 (E)This page deliberately set blankThe text of document CISPR/A/1054/FDIS, future amendment 2 to edition 3 of CISPR 16-2-3, prepared by
26、SC A “Radio-interference measurements and statistical methods“ of IEC/TC CISPR “International special committee on radio interference” was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 55016-2-3:2010/A2:2014. The following dates are fixed: latest date by which the document
27、 has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2015-01-18 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2017-04-18 Attention is drawn to the possibility that some of the elements
28、 of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard CISPR 16-2-3:2010/A2:2014 was approved by CENELEC as a European Standard without any modifi
29、cation. Foreword to amendment A2 3 BS EN 55016-2-3:2010+A2:2014 EN 55016-2-3:2010+A2:2014 (E)Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this documen
30、t. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publica
31、tion Year Title EN/HD Year CISPR 14-1 2005 Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission EN 55014-1 2006 CISPR 16-1-1 - Specification for radio disturbance and immunity measuring apparatus and methods -Part 1-1: Radio d
32、isturbance and immunity measuring apparatus - Measuring apparatus EN 55016-1-1 - CISPR 16-1-2 2003 Specification for radio disturbance and immunity measuring apparatus and methods -Part 1-2: Radio disturbance and immunity measuring apparatus - Ancillary equipment - Conducted disturbances EN 55016-1-
33、2 2004 CISPR 16-1-4 2010 Specification for radio disturbance and immunity measuring apparatus and methods -Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites for radiated disturbance measurements EN 55016-1-4 2010 CISPR 16-2-1 2008 Specification for radio disturba
34、nce and immunity measuring apparatus and methods -Part 2-1: Methods of measurement of disturbances and immunity - Conducted disturbance measurements EN 55016-2-1 2009 CISPR 16-4-1 - Specification for radio disturbance and immunity measuring apparatus and methods -Part 4-1: Uncertainties, statistics
35、and limit modelling - Uncertainties in standardized EMC tests - - CISPR 16-4-2 - Specification for radio disturbance and immunity measuring apparatus and methods -Part 4-2: Uncertainties, statistics and limit modelling - Uncertainty in EMC measurements EN 55016-4-2 - CISPR/TR 16-4-5 - Specification
36、for radio disturbance and immunity measuring apparatus and methods -Part 4-5: Uncertainties, statistics and limit modelling - Conditions for the use of alternative test methods - - 4 BS EN 55016-2-3:2010+A2:2014 EN 55016-2-3:2010+A2:2014 (E)Publication Year Title EN/HD Year IEC 60050-161 1990 Intern
37、ational Electrotechnical Vocabulary (IEV) - Chapter 161: Electromagnetic compatibility - - IEC 61000-4-3 2006 Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test EN 61000-4-3 2006 IEC 61000-4-20 - Electro
38、magnetic compatibility (EMC) - Part 4-20: Testing and measurement techniques - Emission and immunity testing in transverse electromagnetic (TEM) waveguides EN 61000-4-20 - 5 BS EN 55016-2-3:2010+A2:2014 EN 55016-2-3:2010+A2:2014 (E)CONTENTS 1 Scope. 10 2 Normative references . 103 Terms, definitions
39、 and abbreviations 4 Types of disturbance to be measured . 14.1 General . 14.2 Types of disturbance . 14.3 Detector functions . 15 Connection of measuring equipment.6 General measurement requirements and conditions . 16.1 General . 176.2 Disturbance not produced by the equipment under test . 176.2.1
40、 General . 16.2.2 Compliance (conformity assessment) testing . 176.3 Measurement of continuous disturbance 186.3.1 Narrowband continuous disturbance 16.3.2 Broadband continuous disturbance 186.3.3 Use of spectrum analyzers and scanning receivers 186.4 EUT arrangement and measurement conditions 186.4
41、.1 General arrangement of the EUT 186.4.2 .6.4.3 . 216.4.4 . 21 6.4.5 . 216.5 Interpretation of measuring results 6.5.1 Continuous disturbance . 6.5.2 Discontinuous disturbance. 6.6 Measurement times and scan rates for continuous disturbance .6.6.1 General .6.6.2 Minimum measurement times 6.6.3 Scan
42、 rates for scanning receivers and spectrum analyzers6.6.4 Scan times for stepping receivers6.6.5 Strategies for obtaining a spectrum overview using the peak detector .7 Measurement of radiated disturbances .7.1 Introductory remarks .7.2 Loop-antenna system measurements (9 kHz to 30 MHz) .7.2.1 Gener
43、al .7.2.2 General measurement method.7.2.3 Test environment.7.2.4 Configuration of the equipment under test .7.2.5 Measurement uncertainty for LAS7.3 Open-area test site or semi-anechoic chamber measurements (30 MHz to 1 GHz) 7.3.1 Measurand 6.6.6 Timing considerations using FFT-based instruments .1
44、1 66 6 7 17 7 7 8 21 # $ 6 6.5.3 Measurement of the duration of disturbance # $# $EUTrunning-intimeEUT supply6.4 .6 EUT mode of operation 21 6.4 .7 Operation of multifunction equipment 21Operation of the EUTEUT time of operation#$6.4 .8 Determination of arrangement(s) causing maximum emissions 6.4 .
45、9 Recording of measurements # $2425262932323333333434353535$#BS EN 55016-2-3:2010+A2:2014 CISPR 16-2-3:2010+A2:2014 (E)7.3.4 Measurement distance.7.3.5 Antenna height variation7.3.6 Product specification details 7.3.7 Measurement instrumentation7.3.8 Field-strength measurements on other outdoor site
46、s7.3.9 Measurement uncertainty for OATS and SAC 7.4 Fully-anechoic room measurements (30 MHz to 1 GHz) 7.4.1 Test set-up and site geometry .7.4.2 EUT position7.4.3 Cable layout and termination .7.4.4 Measurement uncertainty for FAR .7.5 Radiated emission measurement method (30 MHz to 1 GHz) and radi
47、ated immunity test method (80 MHz to 1 GHz) with common test set-up in semi-anechoic chamber .7.5.1 Applicability.7.5.2 EUT perimeter definition and antenna-to-EUT separation distance 7.5.3 Uniform test volume.7.5.4 Specifications for EUT set-up in common emissions/immunity test setup .7.5.5 Measure
48、ment uncertainty for common emission/immunity set-up and method 7.6 Fully-anechoic room and absorber-lined OATS/SAC measurements (1 GHz to 18 GHz).7.6.1 Quantity to measure 7.6.2 Measurement distance.7.6.3 Set-up and operating conditions of the equipment under test (EUT).7.6.4 Measurement site 7.6.5 Measurement instrumentation7.6.6 Measurement procedure7.6.7 Measurement uncertainty for FAR .7.7 In situ measurements (9 kHz to 18 GHz) .7.7.1
