1、 STDmBSI BS EN IS0 14530-1-ENGL 2000 Lb24bb9 082b38 859 m BRITISH STANDARD Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCS) - Part 1: Designation system and basis for specifications The European Standard EN IS0 14531:1999 has the status of a British Standard ICs 83.080.10 BS EN I
2、S0 14530-1:2000 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGT LAW STDoBSI BS EN IS0 14530-L-ENGL 2000 M lb24bb9 082b839 775 BS EN IS0 14530-1:2000 direction of the Sector Amd. No. Date Committee for Materials and Chemicals, was published under the authority of the Standards Commi
3、ttee and comes into effect on 15 January 2000 National foreword Comments This British Standard is the English ianguage version of EN IS0 14531:1999. It is identical with IS0 14530-1: 1999. The UK participation in its preparation was entrusted to Technical Committee PW42, Fbre reinforced thermosettin
4、g plastics and prepregs, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible internationaVEuropean committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed - monitor related international and European
5、 developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards nomy include an annex which lists nonnative references to international publi
6、cations with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International standards Correspondence Index”, or by using the “Find” facility of the BSI
7、 Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application, Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary
8、of pages This document comprises a front cover, an inside front cover, the EN IS0 title page, the EN IS0 foreword page, the IS0 title page, pages ii and iii, a blank page, pages 1 to 6, an inside back cover and a back cover. The BSI copyright notice displayed in this document inicates when the docum
9、ent WaSlaStiSSUed. O BSI 01-2000 I I ISBN O 580 35885 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 14530.1 November i 999 ICs 83.080.10 English version Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 1 : Designation system and basis for specifications (IS0 1
10、4530-1 :1999) Plastiques - Poudres mouler base de polyester non satur (UP-PMC) - Partie 1: Systme de dsignation et base de spcification (IS0 14530-1:1999) This European Standard was approved by CEN on 13 October 1999. CEN members are bound to comply with the CENKENELEC Intemal Regulations which stip
11、ulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard e
12、xists in three official versions (English, French, Geman). A version in any other language made by translatlon under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards b
13、odies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece. Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal. Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION EUROPISCHES KOMITEE FOR NORM
14、UNG Central secretariat: rue de Stassart, 36 B-1050 Brussels 1999 CEN All rights of exploitation in any fom and by any means resewed worldwide for CEN national Members. Ref. No. EN IS0 14530-1:1999 E EN IS0 14530-1:1999 Foreword The text of the International Standard IS0 14530-1 :1999 has been prepa
15、red by Technical Committee ISOTTC 61 “Plastics“ in collaboration with Technical Committee CEN/TC 249 “Plastics“, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the late
16、st by May 2000, and conflicting national standards shall be withdrawn at the latest by May 2000. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark,
17、 Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. NOTE FROM CENES: The foreword is susceptible to be amended on reception of the German language version. The confirmed or amended foreword, and whe
18、n appropriate, the normative annex ZA for the references to international publications with their relevant European publications will be circulated with the German version. Endorsement notice The text of the International Standard IS0 14530-1:1999 was approved by CEN as a European Standard without a
19、ny modification. EN IS0 14530-1:1999 I NTE RN ATION AL STANDARD IS0 14530-1 First edition 1999-1 1-1 5 Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 1: Designation system and basis for specif ications Plastiques - Poudres mouler base de polyester non satur farfie 7: Sys
20、teme de designation et base de spcification (UP-PMC) - Reference number IS0 14530-1 : 1 999( E) STD-BSI BS EN IS0 L4530-L-ENGL 2000 Ib24bb9 082b843 Ilb EN IS0 14530-1:1999 Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 me
21、mber bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governme
22、ntal and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Dire
23、ctives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 Oh of the member bodies casting a vote. Attention is drawn to the possibility that some of the e
24、lements of this part of IS0 14530 may be the subject of patent rights. IS0 shall not be held responsible for identifying any or all such patent rights. International Standard IS0 14530-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 12, Thermosetting materials. IS0 14530 c
25、onsists of the following parts, under the general title Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs): - Part 1: Designation system and basis for specifications - Part 2: Preparation of test specimens and determination of properties - Part 3: Requirements for selected moulding
26、 compounds Previous page is blank iii STDaBSI BS EN IS0 14530-3-ENGL 2000 = 3624667 0826844 052 II EN IS0 14530-1:1999 Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCS) - Part 1: Designation system and basis for specif ications 1 Scope 1.1 moulding compounds (UP-PMCs). This part o
27、f IS0 14530 establishes a data block system for the designation of unsaturated-polyester powder 1.2 The various types of UP-PMC are differentiated from each other by a classification system based on information about the filler/reinforcement type and content, the intended method of processing, any s
28、pecial properties and those of the special properties used specifically for designation purposes (designatory properties). 1.3 ground material. This part of IS0 14530 is applicable to all UP-PMCs ready for normal use in the form of powder, granules or 1.4 It is not intended to imply that materials h
29、aving the same designation necessarily give the same performance. This part of IS0 14530 does not provide engineering data, performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of processing. If such additional prope
30、rties are required, they shall be determined in accordance with the test methods specified in IS0 14530-2, if suitable. 1.5 using this data block system. Whenever general requirement data, as covered by IS0 14530-3, need to be indicated, this is also done 1.6 To ensure that code-letters and code-num
31、bers remain unambiguous, and to avoid conflicts within the system, any new code-letters or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the secretariats of ISOiTC 61/SC 1, SC 12 and SC 13. 2 Normative references The following normative documents contain provisions whi
32、ch, through reference in this text, constitute provisions of this part of IS0 14530. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of IS0 14530 are encouraged to investigate the possibility o
33、f applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of IS0 and IEC maintain registers of currently valid International Standards. IS0 75-2:1993, Plastics - Determination of t
34、emperature of deflection under load - Part 2: Plastics and ebonite. IS0 179-1 :-), Plastics - Determination of Charpy impact properties - Part I: Non-instrumented impact test. 1) To be published. (Revision of IS0 179:1993) 1 IS0 472:1999, Plastics - Vocabulary. Description block IS0 1043-1:1997, Pla
35、stics - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics. Identity block IS0 lndividual-item block Standard Da ta Data Data Data Data block block block block block 1 2 3 4 5 IS0 1043-2:-*), Plastics - Symbols and abbreviated terms - Part 2: Fillers and reinfor
36、cing materials. IS0 14530-2: 1999, Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 2: Preparation of test specimens and determination of properties. IS0 14530-3: 1 999, Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 3: Requirements for selecte
37、d moulding compounds. i 3 Terms and definitions For the purposes of this part of IS0 14530, the terms and definitions given in IS0 472 and IS0 14530-2 apply, plus the following: 3.1 powder moulding compound powder, granules or ground material capable of flowing freely through the feed systems of pro
38、cessing machines, as well as moulding compounds in the form of flakes which are normally not thought of as powders The abbreviation for powder moulding compound is PMC by analogy with bulk moulding compound (BMC) and sheet moulding compound (SMC). 3.2 UP-PMC abbreviation for powder moulding compound
39、s based on unsaturated-polyester resins for both injection and compression moulding 4 Designation system 4.1 General The designation consists of an optional description block, reading “PMC“, and an identity block comprising the International Standard number and an individual-item block. For unambigu
40、ous designation, the individual-item block is subdivided into five data blocks comprising the following information: 2) To be published. (Revision of IS0 1043-2:1988) 2 Data block 1: Marking block Item 1: Identification of the basic polymer by its symbol, in accordance with IS0 1043-1; Item 2: Natur
41、e of the designatory reinforcement materials or fillers, in accordance with IS0 1043-2; Item 3: Form of the designatory reinforcement materials or fillers, in accordance with IS0 1043-2; Item 4: Nominal content of the designatory reinforcement materials or fillers, in accordance with Table 1, Data b
42、lock 2: Method of processing Method of processing for which the moulding compound is intended, designated in accordance with Table 2. Data block 3: Properties Item 1 : Special properties, in accordance with Table 3; Item 2: Designatory property No. 1 - impact strength determined in accordance with I
43、S0 179-1 ; Item 3: Designatory property No. 2 -temperature resistance determined in accordance with IS0 75-2. Data block 4: Further information, taken from an international, national or company standard. Data block 5 (optional): Additional requirements The first character of the individual-item bloc
44、k shall be a hyphen. The data blocks shall be separated from each other by commas. If a data block is not used, this shall be indicated by an “X“ (= not applicable), but only if another block follows. For labelling purposes, and provided no other blocks follow, the comma between blocks 1 and 2 can b
45、e omitted. There is no need to fill in data blocks if they are not required. 4.2 Data block 1 Item 1 : After the hyphen, unsaturated-polyester powder moulding compounds shall be identified by the symbol UP, in accordance with IS0 1043-1. Mixtures and modifications shall be designated in accordance w
46、ith IS0 1043-1 :1997, subclauses 4 and 5. The following information shall be restricted to designatory fillers/reinforcements used in the material in question: Item 2: Nature of filler/reinforcement, in accordance with Table 1. Item 3: Form of filler/reinforcement, in accordance with Table 1. Item 4
47、: Nominal content (mass %) of filler/reinforcement, in accordance with Table 1. Note, in particular, the following: the same code-letters have different meanings when used for item 2 and item 3; whenever information needs to be indicated only for item 3, an “X“ ( = not applicable) is required for it
48、em 2. 3 4.3 Data block 2 G General purpose M Injection moulding Q Compression moulding In this data block, information about the method of processing is given using the code-letters specified in Table 2. T Transfer moulding X Not specified Z Others The code-letter used to indicate the intended metho
49、d of processing in data block 2 shall be selected carefully. Certain brands of material can be processed in more than one way, e.g. either by compression moulding (Q) or by injection moulding (M). Such brands shall be designated “general purpose“ (G). The designation of special methods of processing shall be reserved for specially modified materials. Table 1 - Code-letters and code-numbers used in data block 1 Nature of filler/reinforcement (in accordance with IS0 1043-2) - C D E G K L1 L2 M P Q R S T W X Z - Carbon Aluminium oxide trihydrate Clay Glass
