1、 ETSI EN 301 908-11 V11.1.2 (2017-01) IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 11: CDMA Direct Spread (UTRA FDD) Repeaters HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 908-11 V11.1.2 (2017-01) 2 Reference REN/MSG
2、-TFES-11-11-RED-C1 Keywords 3G, 3GPP, cellular, digital, IMT, IMT-2000, mobile, radio, regulation, repeater, testing, UMTS, UTRA, WCDMA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association
3、 but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print vers
4、ions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a spe
5、cific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you
6、find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and micro
7、film except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2017. All rights r
8、eserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned
9、 by the GSM Association. ETSI ETSI EN 301 908-11 V11.1.2 (2017-01) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Introduction 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 7g33 Definitions, symbols and abbreviations . 8g3
10、3.1 Definitions 8g33.2 Symbols 8g33.3 Abbreviations . 8g34 Technical requirements specifications . 9g34.1 Environmental profile . 9g34.2 Conformance requirements 9g34.2.1 Introduction. 9g34.2.2 Operating band unwanted emissions 10g34.2.2.1 Definition 10g34.2.2.2 Limit 10g34.2.2.2.1 General operating
11、 band unwanted emission requirements 10g34.2.2.2.2 Operating band emission mask requirements 11g34.2.2.2.3 Protection of the BS receiver in the operating band 12g34.2.2.2.4 Co-existence with services in adjacent frequency bands . 13g34.2.2.2.5 Protection of DTT 13g34.2.2.2.6 Limits for operation in
12、Band 32 13g34.2.2.3 Conformance . 14g34.2.3 Spurious emissions . 14g34.2.3.1 Definition 14g34.2.3.2 Limit 15g34.2.3.2.0 General 15g34.2.3.2.1 Spurious emissions 15g34.2.3.2.2 Co-existence with other systems . 15g34.2.3.3 Conformance . 16g34.2.4 Maximum output power 17g34.2.4.1 Definition 17g34.2.4.2
13、 Limit 17g34.2.4.3 Conformance . 17g34.2.5 Input intermodulation . 17g34.2.5.1 Definition 17g34.2.5.2 Limit 18g34.2.5.2.1 General input intermodulation requirement . 18g34.2.5.2.2 Co-existence with other systems . 18g34.2.5.3 Conformance . 19g34.2.6 Out of band gain . 19g34.2.6.1 Definition 19g34.2.
14、6.2 Limits 19g34.2.6.3 Conformance . 20g34.2.7 Adjacent Channel Rejection Ratio 20g34.2.7.1 Definition 20g34.2.7.2 Limit 20g34.2.7.3 Conformance . 20g34.2.8 Output intermodulation . 21g34.2.8.1 Definition 21g34.2.8.2 Limit 21g3ETSI ETSI EN 301 908-11 V11.1.2 (2017-01) 4 4.2.8.3 Conformance . 21g35 T
15、esting for compliance with technical requirements 21g35.1 Environmental conditions for testing . 21g35.2 Interpretation of the measurement results 21g35.3 Essential radio test suites 23g35.3.0 Introduction. 23g35.3.1 Operating band unwanted emission 23g35.3.1.1 Initial conditions . 23g35.3.1.2 Proce
16、dures . 23g35.3.1.3 Test requirement . 24g35.3.2 Spurious emissions . 24g35.3.2.1 Initial conditions . 24g35.3.2.2 Procedure 24g35.3.2.3 Test requirement . 24g35.3.3 Maximum output power 25g35.3.3.1 Initial conditions . 25g35.3.3.2 Procedure 25g35.3.3.3 Test requirement . 25g35.3.4 Input intermodula
17、tion . 25g35.3.4.1 Initial conditions . 25g35.3.4.2 Procedures . 26g35.3.4.3 Test requirement . 26g35.3.5 Out of band gain . 26g35.3.5.1 Initial conditions . 26g35.3.5.2 Procedure 26g35.3.5.3 Test requirement . 26g35.3.6 Adjacent Channel Rejection Ratio 26g35.3.6.1 Initial conditions . 26g35.3.6.2 P
18、rocedures . 27g35.3.6.3 Test requirement . 27g35.3.7 Output intermodulation . 27g35.3.7.1 Initial conditions . 27g35.3.7.2 Procedures . 27g35.3.7.3 Test requirement . 28g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 29g3Annex
19、 B (normative): Repeater configurations 30g3B.1 Power supply 30g3B.2 Power supply options . 30g3B.3 Combining of Repeaters . 30g3Annex C (informative): Environmental profile specification . 31g3Annex D (informative): Bibliography . 32g3History 33g3ETSI ETSI EN 301 908-11 V11.1.2 (2017-01) 5 Intellec
20、tual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights
21、(IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has b
22、een carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by
23、ETSI Technical Committee Mobile Standards Group (MSG). For non EU countries the present document may be used for regulatory (Type Approval) purposes. The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.10 to provide one voluntary means of conform
24、ing to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.1. Once the present document is cited in the Official Journal of the European Union un
25、der that Directive, compliance with the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive and associated EFTA regulations. The prese
26、nt document is part 11 of a multi-part deliverable. Full details of the entire series can be found in part 1 i.3. National transposition dates Date of latest announcement of this EN (doa): 30 April 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 October
27、 2017 Date of withdrawal of any conflicting National Standard (dow): 31 October 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Dr
28、afting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The present document is part of a set of standards developed by ETSI that are designed to fit in a modular structure to cover rad
29、io equipment within the scope of the Radio Equipment Directive i.1. The present document is produced following the guidance in ETSI EG 203 336 i.2 as applicable. ETSI ETSI EN 301 908-11 V11.1.2 (2017-01) 6 1 Scope The present document applies to the following equipment types: 1) Repeaters for IMT-20
30、00 CDMA Direct Spread (UTRA FDD) This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1. Table 1-1: UTRA Repeater operating bands UTRA FDD Band Direction of transmission UTRA Repeater operating bands I Downlink 2 110 MHz to 2 170 MHz Uplink 1 9
31、20 MHz to 1 980 MHz III Downlink 1 805 MHz to 1 880 MHz Uplink 1 710 MHz to 1 785 MHz VII Downlink 2 620 MHz to 2 690 MHz Uplink 2 500 MHz to 2 570 MHz VIII Downlink 925 MHz to 960 MHz Uplink 880 MHz to 915 MHz XV Downlink 2 600 MHz to 2 620 MHz Uplink 1 900 MHz to 1 920 MHz XVI Downlink 2 585 MHz t
32、o 2 600 MHz Uplink 2 010 MHz to 2 025 MHz XX Downlink 791 MHz to 821 MHz Uplink 832 MHz to 862 MHz XXII Downlink 3 510 MHz to 3 590 MHz Uplink 3 410 MHz to 3 490 MHz XXXII (note 1) (note 2) Downlink 1 452 MHz to 1 496 MHz Uplink N/A NOTE 1: The down link frequency(ies) of this band are paired with t
33、he uplink frequency(ies) of the other FDD band (external) of the dual band configuration. NOTE 2: Radio equipment in band XXXII is only allowed to operate between 1 452 MHz and 1 492 MHz. The present document covers requirements for UTRA FDD Repeater for Releases 4, 5, 6, 7, 8, 9, 10 and 11. This in
34、cludes the requirements for Repeater operating bands from 3GPP Release 12. In addition, the present document covers requirements for UTRA Repeater in the operating bands specified in ETSI TS 102 735 i.9. The present document contains requirements to demonstrate that Radio equipment both effectively
35、uses and supports the efficient use of radio spectrum in order to avoid harmful interference. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited vers
36、ion applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks include
37、d in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 ETSI TS 125 143 (V11.1.0) (02-2013): “Universal Mobile Telecommunications System (UMTS); UTRA repeat
38、er conformance testing (3GPP TS 25.143 version 11.1.0 Release 11)“. ETSI ETSI EN 301 908-11 V11.1.2 (2017-01) 7 2 IEC 60068-2-1 (2007): “Environmental testing - Part 2-1: Tests - Test A: Cold“. 3 IEC 60068-2-2 (2007): “Environmental testing - Part 2-2: Tests - Test B: Dry heat“. 4 ETSI TS 125 141 (V
39、11.12.0) (01-2016): “Universal Mobile Telecommunications System (UMTS); Base Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 11.12.0 Release 11)“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or n
40、on-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their l
41、ong term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Directive 2014/53/EU of the European parliament and of the council of 16 April 2014 on the harmonisation of the l
42、aws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.2 ETSI EG 203 336 (V1.1.1) (08-2015): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of technical parameters for the production of
43、 Harmonised Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU“. i.3 ETSI EN 301 908-1 (V11.1.1): “IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and common requirements“. i.4 ETSI
44、 TR 100 028 (all parts) (V1.4.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics“. i.5 ETSI TS 136 104 (V11.14.0) (01-2016): “LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station (BS) radio
45、 transmission and reception (3GPP TS 36.104 version 11.14.0 Release 11)“. i.6 Recommendation ITU-R SM.329-12 (09-2012): “Unwanted emissions in the spurious domain“. i.7 ETSI EN 301 908-15 (V11.1.1): “IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the
46、 Directive 2014/53/EU; Part 15: Evolved Universal Terrestrial Radio Access (E-UTRA FDD) Repeaters“. i.8 ETSI TS 125 104 (V11.12.0) (01-2016): “Universal Mobile Telecommunications System (UMTS); Base Station (BS) radio transmission and reception (FDD) (3GPP TS 25.104 version 11.12.0 Release 11)“. i.9
47、 ETSI TS 102 735 (V7.1.0) (01-2010): “Universal Mobile Telecommunications System (UMTS); Band-specific requirements for UMTS Frequency Division Duplex (FDD) operation in the bands 1 900 MHz to 1 920 MHz paired with 2 600 MHz to 2 620 MHz and 2 010 MHz to 2 025 MHz paired with 2 585 MHz to 2 600 MHz“
48、. i.10 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European
49、Parliament and of the Council. ETSI ETSI EN 301 908-11 V11.1.2 (2017-01) 8 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: donor coupling loss: coupling loss between the Repeater and the donor Base Station downlink: signal path where Base Station transmits and mobile receives downlink operating band: part of the operating band designated for downlink (BS transmit) maximum output power (Pmax): mean power level per carrier measured at the antenn
