1、 ETSI EN 301 908-3 V11.1.1 (2016-05) IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 3: CDMA Direct Spread (UTRA FDD) Base Stations (BS) HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 908-3 V11.1.1 (2016-05)2 Reference RE
2、N/MSG-TFES-11-03-RED Keywords 3G, 3GPP, cellular, digital, E-UTRA, IMT, IMT-2000, IMT-Advanced, LTE, mobile, radio, regulation, UMTS, UTRA, WCDMA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C A
3、ssociation but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
4、print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kep
5、t on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.as
6、px If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
7、 and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. Al
8、l rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered
9、 and owned by the GSM Association. ETSI ETSI EN 301 908-3 V11.1.1 (2016-05)3 Contents Intellectual Property Rights 6g3Foreword . 6g3Modal verbs terminology 6g3Introduction 6g31 Scope 7g32 References 7g32.1 Normative references . 7g32.2 Informative references 8g33 Definitions, symbols and abbreviatio
10、ns . 9g33.1 Definitions 9g33.2 Symbols 11g33.3 Abbreviations . 12g34 Technical requirements specifications . 13g34.1 Environmental profile . 13g34.2 Conformance requirements 13g34.2.1 Introduction. 13g34.2.2 Spectrum emissions mask . 16g34.2.2.1 Definition 16g34.2.2.2 Limit 16g34.2.2.3 Conformance .
11、 23g34.2.3 Adjacent channel leakage power ratio (ACLR) 24g34.2.3.1 Definition 24g34.2.3.2 Limits 24g34.2.3.3 Cumulative ACLR test requirement in non-contiguous spectrum or multiple-bands . 25g34.2.3.4 Conformance . 25g34.2.4 Transmitter spurious emissions . 26g34.2.4.1 Definition 26g34.2.4.2 Limits
12、26g34.2.4.2.1 Spurious emissions 26g34.2.4.2.2 Co-existence with other systems . 27g34.2.4.2.3 Co-existence with services in adjacent frequency bands . 28g34.2.4.2.4 Protection of the BS receiver of own or different BS 28g34.2.4.2.5 Co-existence with Home BS operating in other bands 30g34.2.4.3 Conf
13、ormance . 30g34.2.5 Base Station maximum output power . 30g34.2.5.1 Definition 30g34.2.5.2 Limit 30g34.2.5.3 Conformance . 30g34.2.6 Transmitter intermodulation . 31g34.2.6.1 Definition 31g34.2.6.2 Limit 31g34.2.6.3 Conformance . 32g34.2.7 Receiver spurious emissions . 32g34.2.7.1 Definition 32g34.2
14、.7.2 Limit 32g34.2.7.3 Conformance . 32g34.2.8 Blocking characteristics 32g34.2.8.1 Definition 32g34.2.8.2 Limit 33g34.2.8.3 Conformance . 37g34.2.9 Receiver intermodulation characteristics 37g34.2.9.1 Definition 37g3ETSI ETSI EN 301 908-3 V11.1.1 (2016-05)4 4.2.9.2 Limit 37g34.2.9.3 Conformance . 3
15、9g34.2.10 Receiver adjacent channel selectivity . 39g34.2.10.1 Definition 39g34.2.10.2 Limit 39g34.2.10.3 Conformance . 40g34.2.11 Home BS output power for adjacent channel protection 40g34.2.11.1 Definition 40g34.2.11.2 Limit 40g34.2.11.3 Conformance . 41g34.2.12 Reference sensitivity level 41g34.2
16、.12.1 Definition 41g34.2.12.2 Limit 41g34.2.12.3 Conformance . 41g35 Testing for compliance with technical requirements 41g35.1 Environmental conditions for testing . 41g35.2 Interpretation of the measurement results 41g35.3 Essential radio test suites 43g35.3.0 Introduction. 43g35.3.1 Spectrum emis
17、sion mask 43g35.3.1.0 General 43g35.3.1.1 Initial conditions . 43g35.3.1.2 Procedures . 44g35.3.1.3 Test requirement . 44g35.3.2 Adjacent channel leakage power ratio (ACLR) 44g35.3.2.1 Initial conditions . 44g35.3.2.2 Procedure 45g35.3.2.3 Test requirement . 45g35.3.3 Transmitter spurious emissions
18、. 45g35.3.3.0 General 45g35.3.3.1 Initial conditions . 45g35.3.3.2 Procedure 46g35.3.3.3 Test requirement . 46g35.3.4 Base Station maximum output power . 46g35.3.4.0 General 46g35.3.4.1 Initial conditions . 46g35.3.4.2 Procedure 46g35.3.4.3 Test requirement . 47g35.3.5 Transmit intermodulation . 47g
19、35.3.5.0 General 47g35.3.5.1 Initial conditions . 47g35.3.5.2 Procedures . 47g35.3.5.3 Test requirement . 48g35.3.6 Receiver spurious emissions . 48g35.3.6.0 General 48g35.3.6.1 Initial conditions . 48g35.3.6.2 Procedure 48g35.3.6.3 Test requirement . 49g35.3.7 Blocking characteristics 49g35.3.7.0 G
20、eneral 49g35.3.7.1 Initial conditions . 49g35.3.7.2 Procedure 50g35.3.7.3 Test requirement . 50g35.3.8 Receiver intermodulation characteristics 50g35.3.8.0 General 50g35.3.8.1 Initial conditions . 50g35.3.8.2 Procedures . 51g35.3.8.3 Test requirement . 51g35.3.9 Receiver adjacent channel selectivity
21、 (ACS) 51g35.3.9.0 General 51g35.3.9.1 Initial conditions . 51g3ETSI ETSI EN 301 908-3 V11.1.1 (2016-05)5 5.3.9.2 Procedure 52g35.3.9.3 Test requirement . 52g35.3.10 Home BS output power for adjacent channel protection 52g35.3.10.1 Initial conditions . 52g35.3.10.2 Procedure 52g35.3.10.3 Test requir
22、ement . 53g35.3.11 Reference sensitivity level 53g35.3.11.0 General 53g35.3.11.1 Initial Conditions . 53g35.3.11.2 Procedure 53g35.3.11.3 Test requirement . 54g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 55g3Annex B (normat
23、ive): Base Station configurations . 57g3B.1 Receiver diversity . 57g3B.2 Duplexers . 57g3B.3 Power supply options . 57g3B.4 Ancillary RF amplifiers 58g3B.5 BS using antenna arrays . 58g3B.5.0 Introduction 58g3B.5.1 Receiver tests 59g3B.5.2 Transmitter tests . 59g3B.6 Transmit diversity and MIMO tran
24、smission 59g3B.7 BS with integrated Iuant BS modem 60g3Annex C (informative): Environmental profile specification . 61g3Annex D (informative): Bibliography . 62g3History 63g3ETSI ETSI EN 301 908-3 V11.1.1 (2016-05)6 Intellectual Property Rights IPRs essential or potentially essential to the present
25、document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respec
26、t of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of ot
27、her IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). For non EU countries
28、the present document may be used for regulatory (Type Approval) purposes. The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.1 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisatio
29、n of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.2. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present docu
30、ment given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 3 of a multi-part deliverable. Full details of the entir
31、e series can be found in part 1 i.5. National transposition dates Date of adoption of this EN: 20 April 2016 Date of latest announcement of this EN (doa): 31 July 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 January 2017 Date of withdrawal of any con
32、flicting National Standard (dow): 31 January 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the
33、expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The present document is part of a set of standards developed by ETSI that are designed to fit in a modular structure to cover radio equipment within the scope of th
34、e Radio Equipment Directive i.2. The present document is produced following the guidance in ETSI EG 203 336 i.3 as applicable. ETSI ETSI EN 301 908-3 V11.1.1 (2016-05)7 1 Scope The present document applies to the following equipment types: 1) Stations for IMT 2000 CDMA Direct Spread (UTRA FDD). This
35、 radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1. Table 1-1: UTRA FDD Base Station operating bands UTRA FDD band Direction of transmission UTRA FDD Base Station operating bands I Transmit 2 110 MHz to 2 170 MHz Receive 1 920 MHz to 1 980 MHz
36、III Transmit 1 805 MHz to 1 880 MHz Receive 1 710 MHz to 1 785 MHz VII Transmit 2 620 MHz to 2 690 MHz Receive 2 500 MHz to 2 570 MHz VIII Transmit 925 MHz to 960 MHz Receive 880 MHz to 915 MHz XV Transmit 2 600 MHz to 2 620 MHz Receive 1 900 MHz to 1 920 MHz XVI Transmit 2 585 MHz to 2 600 MHz Rece
37、ive 2 010 MHz to 2 025 MHz XX Transmit 791 MHz to 821 MHz Receive 832 MHz to 862 MHz XXII Transmit 3 510 MHz to 3 590 MHz Receive 3 410 MHz to 3 490 MHz XXXII (see note) Transmit 1 492 MHz to 1 496 MHz Receive - NOTE: The down link frequenc(ies) of this band are paired with the uplink frequenc(ies)
38、of the other FDD band (external) of the dual band configuration. The present document covers requirements for UTRA FDD Base Stations for 3GPP Releases 99, 4, 5, 6, 7, 8, 9, 10 and 11. This includes the requirements for BS operating bands from 3GPP Release 12. In addition, the present document covers
39、 requirements for UTRA FDD Base Stations in the operating bands specified in ETSI TS 102 735 i.4. The present document contains requirements to demonstrate that Radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference. 2 References
40、 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any ame
41、ndments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. Th
42、e following referenced documents are necessary for the application of the present document. 1 ETSI TS 125 141 (V11.12.0) (01-2016): “Universal Mobile Telecommunications System (UMTS); Base Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 11.12.0 Release 11)“. 2 ETSI TS 145 004 (V11.0.0
43、) (10-2012): “Digital cellular telecommunications system (Phase 2+); Modulation (3GPP TS 45.004 version 11.0.0 Release 11)“. ETSI ETSI EN 301 908-3 V11.1.1 (2016-05)8 3 ETSI TS 125 104 (V11.12.0) (01-2016): “Universal Mobile Telecommunications System (UMTS); Base Station (BS) radio transmission and
44、reception (FDD) (3GPP TS 25.104 version 11.12.0 Release 11)“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, t
45、he latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the p
46、resent document but they assist the user with regard to a particular subject area. i.1 Commission implementing decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institut
47、e as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. i.2 Directive 2014/53/EU of the European parliament and of the council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market
48、of radio equipment and repealing Directive 1999/5/EC. i.3 ETSI EG 203 336 (V1.1.1) (08-2015): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directi
49、ve 2014/53/EU“. i.4 ETSI TS 102 735 (V7.1.0): “Universal Mobile Telecommunications System (UMTS); Band-specific requirements for UMTS Frequency Division Duplex (FDD) operation in the bands 1 900 MHz to 1 920 MHz paired with 2 600 MHz to 2 620 MHz and 2 010 MHz to 2 025 MHz paired with 2 585 MHz to 2 600 MHz“. i.5 ETSI EN 301 908-1 (V11.1.1): “IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and common requirements“. i.6 ETSI TR 100 028 (all parts): “Electrom
