1、 ETSI TS 102 922-1 V7.2.0 (2011-11) Smart Cards; Test specification for the ETSI aspects of the IC_USB interface; Part 1: Terminal features (Release 7) floppy3Technical Specification ETSI ETSI TS 102 922-1 V7.2.0 (2011-11)2Release 7 Reference RTS/SCP-00USBTv720 Keywords smart card, terminal, USB ETS
2、I 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be d
3、ownloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the refer
4、ence shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents
5、is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permissio
6、n. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2011. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Mark
7、s of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 102 922-1 V7.2.0 (2011-11)3Release 7 Contents Intellectual Property Rights 6g3Foreword . 6g3Introduction 6g31 Sc
8、ope 7g32 References 7g32.1 Normative references . 7g32.2 Informative references 8g33 Definitions, symbols and abbreviations . 8g33.1 Definitions 8g33.2 Symbols 8g33.3 Abbreviations . 9g33.4 Formats . 9g33.4.1 Format of the table of optional features 9g33.4.2 Format of the applicability table . 9g33.
9、4.3 Status and Notations . 10g34 Test environment 10g34.1 Table of optional features . 10g34.2 Applicability table 11g34.3 Information provided by the device supplier 11g34.4 Test Equipment (TE) 12g34.4.1 Measurement/setting uncertainties 12g34.4.2 Default conditions for DUT operation 12g34.4.2.1 Te
10、mperature 12g34.4.3 Minimum/maximum conditions for DUT operation . 12g34.4.4 Void 12g34.4.5 ATRs to be used by the UICC simulator 12g34.4.5.1 ATR that indicates that UICC is USB capable and indicates support of classes B and C 13g34.4.5.2 Void. 13g34.4.5.3 Void. 13g34.4.6 USB Descriptors to be used
11、by the UICC simulator . 13g34.4.6.1 Single configuration, Single interface . 13g34.4.6.1.1 Device Descriptor (Single Configuraton) 13g34.4.6.1.2 Configuration Descriptor (ICCD Control B) . 14g34.4.6.2 Multiple configurations, Single interface 14g34.4.6.2.1 Device Descriptor (Multiple Configuraton 1)
12、 . 14g34.4.6.2.2 Configuration Descriptors (ICCD Control B and ICCD Bulk) . 15g34.4.6.3 Multiple Configurations, Multiple interfaces 16g34.4.6.3.1 Device Descriptor (Multiple Configuraton 2) . 16g34.4.6.3.2 Configuration Descriptors (ICCD Control B, ICCD Bulk, EEM and MSC) . 17g34.4.6.4 Multiple con
13、figurations, Single interface, Extended APDU . 20g34.4.6.4.1 Device Descriptor (Multiple Configuraton 3) . 20g34.4.6.4.2 Configuration Descriptors (ICCD Control B and ICCD Bulk, Extended APDU) . 21g34.4.6.5 Single Configuration, No ICCD interface support 22g34.4.6.5.1 Device Descriptor (Single Confi
14、guraton) 22g34.4.6.5.2 Configuration Descriptor (EEM and MSC) . 23g34.4.6.6 Multiple configurations, Alternative Single interface . 24g34.4.6.6.1 Device Descriptor (Multiple Configuraton 4) . 24g34.4.6.6.2 Configuration Descriptors (ICCD Bulk and ICCD Control B) . 24g34.5 Test execution 26g34.5.1 Pa
15、rameter variations . 26g34.6 Pass criterion 26g35 Conformance Requirements . 27g35.1 USB UICC system architecture 27g3ETSI ETSI TS 102 922-1 V7.2.0 (2011-11)4Release 7 5.2 Physical characteristics . 27g35.3 Electrical characteristics . 28g35.4 Initial communication establishment procedures . 28g35.5
16、 USB interface operational features . 30g35.6 Protocol stacks for USB UICC applications . 31g35.7 USB Descriptors of a USB UICC 31g35.8 Assigned values for vendor specific USB requests 31g36 Test cases 32g36.1 Void 32g36.2 Void 32g36.3 Basic Electrical Tests . 32g36.3.1 Supply Voltage Value . 32g36.
17、3.1.1 Test case 1: Phase preceding Terminal power on . 32g36.3.1.1.1 Test execution 32g36.3.1.1.2 Initial conditions 32g36.3.1.1.3 Test procedure . 32g36.4 Activation Tests 32g36.4.1 Voltage-Activation 32g36.4.1.1 Test case 1: Selection of voltage class C as lowest supported voltage, no support of c
18、lass B . 32g36.4.1.1.1 Test execution 32g36.4.1.1.2 Initial conditions 33g36.4.1.1.3 Test procedure . 33g36.4.1.2 Test case 2: Selection of voltage class C as lowest supported voltage, with support of class B 33g36.4.1.2.1 Test execution 33g36.4.1.2.2 Initial conditions 33g36.4.1.2.3 Test procedure
19、. 34g36.4.1.3 Void. 34g36.4.1.4 Void. 34g36.4.1.5 Void. 34g36.4.1.6 Test case 6: USB Interface Activation 34g36.4.1.6.1 Test execution 34g36.4.1.6.2 Initial conditions 34g36.4.1.6.3 Test procedure . 35g36.4.1.7 Void. 35g36.5 Initialization Tests 35g36.5.1 Configuration 35g36.5.1.1 Test Case 1: Set a
20、ddress Test at USB Full Speed . 35g36.5.1.1.1 Test execution 35g36.5.1.1.2 Initial conditions 35g36.5.1.1.3 Test procedure . 36g36.5.2 Power Negotiation 36g36.5.2.1 Test case 1: Power Negotiation support 36g36.5.2.1.1 Test execution 36g36.5.2.1.2 Initial conditions 36g36.5.2.1.3 Test procedure . 36g
21、36.5.2.2 Test case 2: Power Negotiation, Voltage Class not supported 36g36.5.2.2.1 Test execution 36g36.5.2.2.2 Initial conditions 36g36.5.2.2.3 Test procedure . 37g36.5.2.3 Test case 3: Power Negotiation, Class B Activation preferred . 37g36.5.2.3.1 Test execution 37g36.5.2.3.2 Initial conditions 3
22、7g36.5.2.3.3 Test procedure . 37g36.5.2.4 Test case 4: Power Negotiation with more than minimum current . 37g36.5.2.4.1 Test execution 37g36.5.2.4.2 Initial conditions 37g36.5.2.4.3 Test procedure . 38g36.5.3 Resume Time Negotiation 38g36.5.3.1 Test case 1: Resume Time Negotiation . 38g36.5.3.1.1 Te
23、st execution 38g36.5.3.1.2 Initial conditions 38g3ETSI ETSI TS 102 922-1 V7.2.0 (2011-11)5Release 7 6.5.3.1.3 Test procedure . 38g36.6 Descriptors . 39g36.6.1 Standard-Descriptors 39g36.6.1.1 Device Descriptor . 39g36.6.1.1.1 Test Case 1: Device Descriptor Test . 39g36.6.1.2 Configuration and Interf
24、ace Descriptors . 39g36.6.1.2.1 Test Case 1: ICCD Control Transfer configuration Test, single interface . 39g36.6.1.2.2 Test Case 2: Multiple ICCD configuration, single interface test . 40g36.6.1.2.3 Test Case 3: Multiple configuration, multiple interfaces test 40g36.6.1.2.4 Test Case 4: Configurati
25、on Descriptor and no ICCD support from the USB UICC . 41g36.6.2 Class Specific-Descriptors 41g36.6.2.1 ICCD Class Descriptor . 41g36.6.2.1.1 Test Case 1: ICCD Class Descriptor Test 41g36.7 Protocol Stack and Higher Level 42g36.7.1 ICCD - APDU based UICC Applications . 42g36.7.1.1 Test Case 1: ICCD C
26、ontrol B Interface. 42g36.7.1.1.1 Test execution 42g36.7.1.1.2 Initial conditions 42g36.7.1.1.3 Test procedure . 42g36.7.1.2 Test Case 2: ICCD Bulk Interface . 42g36.7.1.2.1 Test execution 42g36.7.1.2.2 Initial conditions 42g36.7.1.2.3 Test procedure . 43g36.7.2 EEM - Ethernet Emulation Model 43g36.
27、7.2.1 Test case 1: EEM Echo Test . 43g36.7.2.1.1 Test execution 43g36.7.2.1.2 Initial conditions 43g36.7.2.1.3 Test procedure . 43g3Annex A(informative): List of test cases for each conformance requirement 44g3Annex B (informative): Additionnal optional requirements and test cases for Electrical cha
28、racteristics. 46g3Annex C (informative): Bibliography . 47g3Annex D (informative): Change history . 48g3History 49g3ETSI ETSI TS 102 922-1 V7.2.0 (2011-11)6Release 7 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The infor
29、mation pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the
30、ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the u
31、pdates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Smart Card Platform (SCP). The contents of the present document are subject to continuing work within TC SCP
32、 and may change following formal TC SCP approval. If TC SCP modifies the contents of the present document, it will then be republished by ETSI with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 0 early working draft; 1 pre
33、sented to TC SCP for information; 2 presented to TC SCP for approval; 3 or greater indicates TC SCP approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when ed
34、itorial only changes have been incorporated in the document. The present document is part 1 of a multi-part deliverable covering the Test specification for the USB interface, as identified below: Part 1: “Terminal features“; Part 2: “UICC features“. Introduction The present document defines test cas
35、es for the terminal relating to the USB interface, as specified in TS 102 600 1. The aim of the present document is to ensure interoperability between the terminal and the UICC independently of the respective manufacturer, card issuer or operator. ETSI ETSI TS 102 922-1 V7.2.0 (2011-11)7Release 7 1
36、Scope The present document covers the minimum characteristics which are considered necessary for the terminal in order to provide compliance to TS 102 600 1. The present document specifies the test cases for: the characteristics of the Inter-Chip USB electrical interface between the USB UICC and the
37、 USB UICC-enabled terminal; the initial communication establishment and the transport protocols; the communication layers between the USB UICC and the USB UICC-enabled terminal. Test cases for the USB UICC-enabled terminal relating to TS 102 221 2 interface are out of scope of the present document.
38、2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) appli
39、es. In the case of a reference to a TC SCP document, a non specific reference implicitly refers to the latest version of that document in the same Release as the present document. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbo
40、x.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. 1 ETSI TS 102 600: “Sm
41、art Cards; UICC-Terminal interface; Characteristics of the USB interface“. 2 ETSI TS 102 221: “Smart Cards; UICC-Terminal interface; Physical and logical characteristics“. 3 ETSI TS 102 223: “Smart Cards; Card Application Toolkit (CAT)“. 4 ISO/IEC 9646-7: “Information technology - Open Systems Inter
42、connection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. 5 Universal Serial Bus Specification Revision 2.0, USB Implementers Forum. NOTE: Available at http:/www.usb.org/developers/docs. This is a ZIP package containing the following: square4 The or
43、iginal USB 2.0 specification released on April 27, 2000. square4 The “USB On-The-Go supplement“ Revision 1.3 as of December 5, 2006. square4 The “Inter-Chip USB supplement to the USB 2.0 Specification“ Revision 1.0 March 13, 2006. square4 Errata and Engineering Change Notices. In the context of the
44、present document, this reference, abbreviated as “USB 2.0“, is used specifically in relation to the original USB 2.0 specification and associated errata and Engineering Change Notices, while its supplements are referred through separate references. ETSI ETSI TS 102 922-1 V7.2.0 (2011-11)8Release 7 6
45、 “Inter-Chip USB supplement to the USB 2.0 Specification“, Revision 1.0 March 13, 2006 published as part of the Universal Serial Bus Revision 2.0 specification package (see TS 102 223 3). NOTE: available at http:/www.usb.org/developers/docs. 7 Universal Serial Bus, “Mass Storage Class Specification
46、Overview“, Revision 1.2, USB Implementers Forum, Device Working Group: Mass Storage. NOTE: Available at http:/www.usb.org/developers/devclass_docs. 8 “Universal Serial Bus Mass Storage Class Bulk-Only Transport“ Revision 1.0. NOTE: Available at http:/www.usb.org/developers/devclass_docs. 9 Universal
47、 Serial Bus “Device Class: Smart Card ICCD Specification for USB Integrated Circuit(s) Card Devices“ Revision 1.0. NOTE: Available at http:/www.usb.org/developers/devclass_docs. 10 “Universal Serial Bus Communications Class Subclass Specification for Ethernet Emulation Model Devices“, Revision 1.0,
48、USB Implementers Forum, Device Working Group: Communication. NOTE: Available at http:/www.usb.org/developers/devclass_docs. 11 ANSI/INCITS 408-2005: “Information Technology - SCSI Primary Commands - 3 (SPC-3)“. NOTE: Available at http:/www.t10.org. 12 ETSI TS 102 230: “Smart cards; UICC-Terminal int
49、erface; Physical, electrical and logical test specification (Release 7)“. 13 ETSI TS 102 613: “Smart Cards; UICC - Contactless Front-end (CLF) Interface; Part 1: Physical and data link layer characteristics“. 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. Not applicable. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms an
