1、 A-A-1349A August 20,2002 SUPERSEDING February 26,1980 A-A-1349 COMMERCIAL ITEM DESCRIPTION WRENCH, SLUGGING, BOX, 12 POINT The General Services Administration has authorized the use of this commercial item description by all federal agencies. 1. SCOPE. This commercial item description covers wrench
2、es suitable for hexagonal boltheads and nuts. . .- 2. CLASSIFICATION. Not applicable 3. SALIENT CHARACTERISTICS. 3.1 Design. Wrenches shall be similar to figure 1 and figure 2. Wrench dimensions and sizes shall conform to section 3.2. Figure 1 I 1 PF- I Beneficial comments, recommendations, addition
3、s, deletions, clarifications, etc. and any other data which may improve this document should be sent to: General Services Administration, Federal Supply Service, Hardware Superstore (GFEE), 1500 Bannister Rd. Bldg. #6, Kansas City, Missouri. 64 13 1. FSC 5120 Provided by IHSNot for ResaleNo reproduc
4、tion or networking permitted without license from IHS-,-,-A-A-1349A Figure 2 3.2 Dimensions and Sizes. Wrench Opening (distance across flats) Head Slugging Block Overall Length Outside Diameter Thickness Width Thickness A B C D E F 1-112 2-114 1 1-711 6 518 6 1-114 2- 111 6 15/16 1-5/16 518 6 1-13/1
5、6 2-1 1/16 1-114 1-518 718 7 1-5/16 2-1/16 15/16 1-511 6 518 6 1-518 2-711 6 1-3/16 1-518 13/16 7 1-7/16 2-114 1 1-711 6 518 6 1-718 2-314 1-114 1-518 718 7 Inches Min. Inches Max. Inches Min. Inches Min. Inches Min. Inches .I 2 3-114 1-711 6 2 1 7- 1 /2 2-1/16 3-518 1-518 2- 1 /4 1-511 6 10-314 2-
6、1 /4 3-112 1-112 2 1 7- 112 2-311 6 3-112 1-112 2 1 7-112 2-318 3-314 1-1 1/16 2-318 1-118 8-7/16 2-518 4- 1 /8 1 -3/4 2-318 1-1/4 8-711 6 3 4-518 2 2-314 1-318 9-112 3-318 5-114 2-1116 3-118 1-9/16 10 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-
7、A-A- 1349A 3.3 Materials. The materials used in the manufacturing of the wrenches shall be such as to produce wrenches conforming to the physical requirements hereinafter described. 3.4 Marking. Each wrench shall be marked on one of the faces or on the handle as close to each head as is practicabl
8、e in a plain and permanent manner. In addition to size markings, each wrench shall be marked in a plain and permanent manner with the manufacturers name or trademark of such known character that the source of manufacture may be readily determined. 3.5 Hardness. Wrenches shall be treated to a Rockwel
9、l C hardness not less that 28 nor more than 38 when tested per ASTM-E- 18. 3.6 Wrench Ends. One end shall have a box opening with 12 point (double hexagon). Other end shall terminate with a surface suitable for slugging. 3.7 Wrench Opening. The nut and bolt head-engaging surfaces of the wrench shall
10、 be finished in a smooth and well-defined manner. Wrench opening tolerances shall be such as to insure acceptance when gaged with gages conforming to ASME B 107.17M. 3.8 Finish. 3.8.1 Surface Finish. All surfaces shall be thoroughly cleaned, free from cracks, and essentially free from burrs, pits, n
11、odules, and other detrimental deficiencies. 3.8.2 Coatings. The coating shall be chrome plate (3.8.2.1) phosphate (3.8.2.2), oxide (3.8.2.3), or alternate coating (3.8.2.4) and shall be specified in the contract or order. The coating shall be adherent, smooth, continuous, and free from uncoated area
12、s, pits, blisters, nodules, and any other defects that would interfere with their protective value and serviceability. 3.8.2.1 Chrome Plate. Wrenches shall have a protective-decorative nickel-chromium plating. The nickel thickness shall be a minimum of 0.0001 50 in. The chromium thickness shall be a
13、 minimum of 0.000003 in. A nickel-iron undercoating (1 6% iron max.) may be substituted for nickel. 3.8.2.1.1 Chrome Plate Tests. One measurement of the thickness of each electroplated coating shall be conducted in accordance with any of the following, as appropriate, methods: -1 ASTM B 487: Standar
14、d Method for Measurement of metal and oxide coating thickness by microscopical examination of a cross section. ASTM B 499: Standard Test Method for Measurement of coating thickness by the magnetic method: nonmagnetic coatings of magnetic basis metals. ASTM B 504: Standard Method for Measurement of t
15、hickness of metallic coatings by the coulometric method. ASTM B 530: Standard Test Method for Measurement of coating thickness by the magnetic method: electrodeposited nickel coatings on magnetic and nonmagnetic substrates. ASTM B 568: Standard Test Method for Measurement of coating thickness by x-r
16、ay 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A- 1349A spectrometry. ASTM B 748: Standard Method for Measurement of thickness of metallic coatings by measurement of cross section with a scanning electron microscope. ASTM A 754: Standard Test
17、 Method for Coating thickness by x-ray fluorescence. Visible contact marks resulting from electroplating operations shall be confined to the interior of the wrenching and drive openings. Surfaces of the electroplated tool shall be adherent, smooth, continuous, and free of visible defects, such as bl
18、isters, pits, roughness, cracks, and uncoated areas. Surfaces shall not be stained or discolored and shall have a bright appearance. The electroplated tool shall be clean and free of damage. The tool shall be tested for adhesion of electroplated materials in accordance with ASTM B571, Standard Test
19、Methods for Adhesion of Metallic Coatings, by one of the following methods: Grind-Saw, Push, File, or Burnishing. 3.8.2.2 Phosphate. .,Wrenches shall have a chemically produced phosphate coating followed by a coating of rust preventive. 3.8.2.3 Black Oxide. Oxide coated wrenches shall have a coating
20、 consisting of a chemically produced oxide followed by a coating of rust preventive. 3.8.2.4 Alternative Coatings. Alternate coatings may be used in lieu of nickel - chromium and shall be subjected to the Alternative Coating Test as specified below. 3.8.2.4.1 Alternative Coating; Test. The test cons
21、ists of an adhesion, abrasion, and corrosion test specified below: Test Preparation. The quantity and condition of the wrenches used for the following testing shall be per the manufacturers standard practice or as mutually agreed to by the manufacturer and the General Services Administration. Adhesi
22、on Test. Sample wrenches shall pass the file or grind-saw test of ASTM B 571 Abrasion Test. Sample wrenches shall have no base material exposed after being subjecting to 1 O0 liters of falling sand per ASTM D 968 Method A. .I Corrosion Test. The exterior surfaces of sample wrenches shall be tested f
23、or corrosion resistance by exposure to a 72-hour salt spray test, as specified in ASTM B 117, without falling below the ASTM B 537 rating of 6. 4. REGULATORY REQUIREMENTS. 4.1 Recovered Material. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in ac
24、cordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A- 1349A 5. PRODUCT CONFORMANCE. 5.1 Product Conformance. The product provided shall meet the salient characteristics of t
25、his Commercial Item Description, conform to the producers own drawing, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 5.2 Responsibility for Inspect
26、ion. Unless otherwise specified, the contractor is responsible for the performance of all inspection requirements and may use any commercial facilities (including the contractors own facilities) suitable for performance of the inspection requirements, unless disapproved by the Government. The Govern
27、ment reserves the right to perform any of the inspections deemed necessary to assure the item conforms to the specified requirements. 6. PACKAGING. Preservation, packaging and marking shall be as specified in the contract or order. 7. NOTES. This section contains information of a general or explanat
28、ory nature that is not mandatory. 7.1 Source of Documents. American Society of Mechanical Engineers (ASME), Manuel Gutierrez, Managing Director, 3 Park Avenue, New York, NY 10016. American Society for testing and Materials (ASTM), 100 Barr Harbor Dr., W. Conshohocken, PA, 19428-2959. Federal Acquisi
29、tion Regulation (FAR): Government Printing Office, Superintendent of Documents, Washington DC. 20401 -9371. 7.2 Ordering; data. Purchasers should select the preferred options permitted herein and should include the following information in procurement documents. a. Title, number, and date of Commerc
30、ial Item Description. b. Wrench Opening c. Type of Coating d. Packaging Requirements .- - 7.3 National Stock Numbers CNSNs). A list of NSNs assigned that correspond to this CID. The list may not be indicative of all possible NSNs associated with the CID. NSN 5 120-00-174-1 834 5 120-00-1 74- 183 1 5
31、 120-00-222- 1600 5120-00-174-1832 5 120-00-222- 1594 5 120-00- 174- 1 833 5 120-00-222- 160 1 5 120-00-224-3 109 Wrench Opening 1-1/2 1-1/4 1-1 3/16 1-511 6 1-518 1-74 6 1-718 2 NSN Wrench Opening 5120-00-174-1842 2-1/16 5 120-00-224-3 1 1 1 5 120-00-224-3 1 1 O 5 120-00-224-3 1 12 2-318 5 120-00-2
32、24-3 1 14 2-518 5 120-00-224-3 1 16 3 5 120-00-224-3 1 1 8 2-114 2-311 6 3-318 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A- 1349A 7.4 Key words. Wrench; Slugging, Box, 12-Point. MILITARY INTERESTS: NONE: DoD has no registered interest in revisions and amendments to this Commercial Item Description until further notice. Preparing Activity: GSA-FSS 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
