1、A P A-A-3975B m 9999974 0374594 2T5 m INCH FOUND A-A-1975B SUPERSEDING A-A- 197SA 24. 1997 April 3, 1986 COMMERCIAL ITEM DESCRIPTION DOWEL, WOOD The General Services Administration has authorized the use of this commercial item description by all federal agencies. 1. SCOPE 1.1 a. This commercial ite
2、m description covers wooden dowel rods for general purpose use. 2. CLASSIFICATION . 2.1 (Ilassification The dowel rods shall be of the following type and diameter, *. as specified (see 7.2). Type I - Rod dowel Diameter - Inch (mm) 1/8 (3.2) 3/16 (4.8) 1/4 (6.3) 5/16 (7.9) 3/8 (9.5) Inch (mm) 7/16 (1
3、1.1) 1/2 (12.7) 5/8 (15.8) 7/8 (22.2) 3/4 (19.0) Inch (mm) 1 (25 -4) 1-1/8 (28.5) 1-1/4 (31.7) 1-1/2 (38.1) Type II - Deleted 3. SALIENT CHARACTERISTICS 3.1 Material . Unless otherwise specified (see 7.21, the wood species shall be at the option of the manufacturer and of the type accepted within in
4、dustry for the manufacture of this product. 3.2 Uook/Row. The dowel rod shall have no crook exceeding 3/8 inch (9.5 mm) and no bow exceeding 3/4 inch (19.0 mm) in 36 inches (914.4 mm). a. Crook is any discreet departure of the dowel axis from a straight line extending through the center of the dowel
5、 ends, within the dowel length. b. Bow is any continuous departure of the dowel axis from a straight line extending through the center of the dowel . ends, in the overall dowel length. % 3.3 Cross ur a. Slope of grain shall not exceed 1 inch (25.4 mm) in 12 inches (304.8 mm). Beneficial comments, re
6、commendations, additions, deletions, this document FSC 5510 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-1975B 9999974 0174595 131 A-A- 19 75B 3.4 Dimencians . Unless otherwise specified, the rod dowel length shall be 36 inches (914.4 mm) , p
7、lus 1/2 inch (12.7 mm) , minus 1/16 inch (1.6 mm) . The tolerance on the diameter shall be f 3 percent. 3.5 surfaces, splinters, or splits. 3.6 -. The values stated in inch-pound units are to be regarded as the standard. The metric values stated in parentheses are for information purposes only. 3.7
8、Wric . Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, providing they fall within the tolerances specified and all other requirements of this document are met. If a product is manufactured to metric dimensions and those
9、dimensions exceed the tolerances specified in the inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable. . The rod dowels shall be smoothly finished and free of rough 4. REGULATORY REQUIREMENTS 4.1 -tom re- . The offeror/contractor is encoura
10、ged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 5. QUALITY ASSURANCE PROVISIONS 5.1 ProductConformanee. The products provided shall meet the salient characteristics of this commercial item description,
11、 conform to the producers own drawings, specifications, standards, and quality assurance practices and be the same product offered for sale in the commercial market. reserves the right to require proof of such conformance. 6. PACKAGING The government 6.1 Packacrins . Preservation, packing, and marki
12、ng shall be as specified in the contract or order. 7. NOTES *. 7.1 A . Rod dowels conforming to this commercial item description shall be identified by a part number configuration consisting of identification of a portion of the CID number, type, and diameter. An example of the part number configura
13、tion is shown below. This part numbering system is intended for identification and cross-indexing of the item within the Federal cataloging system. The following part identification numbering procedure is for government purposes and does not constitute a requirement for the contractor. AA1 9 7- III
14、Example: (AA19751A) = Type I, 1/8 inch diameter Diameter A = 1/8 B = 3/16 D = 5/16 E = 3/8 c = 1/4 F = 7/16 (see 7.3) K = 7/8 G = 7/16 L=l H = 1/2 M = 1-1/8 I = 5/8 N = 1-1/4 J = 3/4 o = 1-1/2 i Commercial item description number 2 Provided by IHSNot for ResaleNo reproduction or networking permitted
15、 without license from IHS-,-,-A - A - I9 7 5 B W 9999974 0174596 O78 = A-A-1975B 7.2 . Purchasers should select the preferred options permitted herein and include the following information in procurement documents (if applicable). a. Title, number and date of this commercial item description. b. me,
16、 diameter, and wood species required. c. Preservation, packing, and marking desired. 7.3 NationalCtockys (“s) : The following is a list of NSNs assigned which correspond to this CID. The list may not be indicative of all possible NSNs associated with the CID. NSN 5510-00-223-8254 5510-00-223-7182 55
17、10-00-240-0067 5510-00-223-0952 5510-00-240-0068 5510-00-270-6246 5510-00-497-5463 5510-00-240-0069 5510-00-240-0070 5510-00-240-0071 5510-00-978-6858 5510-00-223-0953 5510-00-223-0954 5510-00-223-0955 5510-00-223-0956 MILITARY INTERESTS: AF - 99 Diameter (inch) Part number 1/8 3/16 1/4 3/8 1/2 5/8
18、3 /4 7/8 5 / 1.6 7/16 7/16 1 1-1/8 1-1/4 1-1/2 AA1975lA AA19751B AAl9751C AA1 97 S1D AA1 9 75 1E (2-3/8 inch length (60.3 mm) AA19751F AA19751G AA19751H AA197511 AA19751J AA19751K AA19751L AA19751M AA1975lN AA197510 CIVIL AGENCY COORDINATING ACTIVITY: GSA- FSS Preparing Activity: GSA- FS S &view Ar+ ivitv : AF - 84 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
