1、I INCH-POUND IA-A-2322AMay 30,2003SUPERSEDINGA-A-2322September 27, 1985 COMMERCIAL ITEM DESCRIPTIONFILE, HAND (AMERICAN PATTERN), THREE SQUAREThe General Services Administration has authorized the use of this commercial item descriptionby all federal agencies.1. SCOPE. This commercial item descripti
2、on covers hand files used for tiling internal angles, clearingout comers, and for filing taps and cutters in the annealed state.2. CLASSIFICATION.Type I Bastard-cutType II Second-cutType III Smooth-cuta71 3. SALIENT CHARACTERISTICS.3.1 Desirer. The file shall be tapered on all sides at least one-thi
3、rd (1/3) of the length to the point.Double-cut on each surface (two sets of parallel cuts on the surface, one set crossing the other), Sides atany point on the file shall be of equal width. Edges set (blunted), then double-cut. No portion shallextend outside of the area of the largest cross-section
4、of the tile. The file shall be furnished in three (3)types and assorted sizes as shown in section 3.2,Figure 1RegularIBeneficial comments, recommendations, additions, deletions, clarifications, etc. and any other datawhich may improve this document should be sent to: General Services Administration,
5、 Federal Ia711Supply Service, Hardware SuperStore (6FEE), 1500 E. Bannister Rd Bldg. #6, Kansas City,Missouri 64131.FSC5110Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-2322A3.2 Dimensions.Dimensions at largest Number of teeth per inch surfaceL
6、ength section A Min MaxInches Inch6 1/28 5/810 3/46 1/28 5/810 3146 1128 5/810 3/4Bastard-cut332522Second-cut433631Smooth-cut554439372925494135614944Length dimension: Measured from the point (free or front end) to the heel (junction of the tang with thebody of the file) and have a tolerance of 1/8 i
7、nch,.0Tolerance: Width (A) - +1/16 inch3.3 Material. The file shall be of a carbon alloy steel3.4 Shall be of a conventional shape and size suitable for attachment to a wood handle.Tempered to a maximum hardness of 45 on the Rockwell C scale when tested per ASTM El 8, ,It shallbe measured at a point
8、 approximately midway of its length and width.3.5 = Shall be uniformly cut or etched and of uniform height throughout the fully cut portion.Cutting surfaces shall be hardened to a uniform hardness. The distance between the heel and point ofthe file, excluding the tang, shall be hardened to not great
9、er than 68 nor less than 64 on the Rockwell Cscale when tested per ASTM E 18. The tile shall be free from decarburization and brittleness.3.6 Marking. The file shall be marked with the name of the manufacturer or with a trademark of suchknown character that the source of manufacture maybe readily de
10、termined.3.7 Workmanship. The teeth of the file shall be well-defined, sharp, and uniform in height and form.There shall be no evidence of rust or other defect which may impair serviceability, durability orappearance.4. REGULATORY REQUIREMENTS2Provided by IHSNot for ResaleNo reproduction or networki
11、ng permitted without license from IHS-,-,-A-A-2322A4.1 Recovered Materials, The offeror/contractor is encouraged to use recovered materials to themaximum extent practicable, in accordance with paragraph 23.403 of the Federal acquisition Regulation(FAR).4.2 Metric uroducts, Products manufactured to m
12、etric dimensions will be considered on an equal basiswith those manufactured using inch-pound units, provided they fall within the tolerances specified(using conversion tables contained in the latest revision of Federal Standard 376) and all otherrequirements of this document are met. If a product i
13、s manufactured to metric dimensions and thosedimensions exceed the tolerances specified in the inch- pound units, a request should be made to thecontracting officer to determine if the product is acceptable.5. PRODUCT CONFORMANCE.5.1 Product Conformance. leproduct provided shall meet thesalient char
14、acteristics of thisCommercial Item Description, conform to the producers own drawing, specifications, standards, andquality assurance practices, mdbethe smeproduct offered forsale inthecommercial mmket. Thegovernment reserves the right to require proof of such conformance.5.2 Responsibility for Insp
15、ection. Unless otherwise specified, thecontractor irresponsible fortlleperformance of all inspection requirements and may use any commercial facilities (including thecontractors own facilities) suitable for performance of the inspection requirements, unless disapprovedby the Government. The Govermne
16、nt reserves the right to perform any of the inspections deemednecessary to assure the item conforms to the specified requirements.a71 6. PACKAGING. Preservation, packaging mdmarking shall beasspecified inthe contractor order.7. NOTES. This section contains infomation ofageneral orexplanatory nature
17、that isnot mandatory.7.1 Source of Documents.American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, PO Box C700, WestConshohocken, PA 19428-2959.Federal Acquisition Regulation (FAR): Government Printing Office, Superintendent of Documents,Washington, DC 20401-9371.GSA Specificatio
18、n Section (3FP-E), Suite 8100,470 LEnfant Plaza, SW, Washington, DC 20407.7.2 Orderir-uz data. Purchasers should select the preferred options permitted herein and should include thefollowing information in procurement documents.:.c.d.Title, number, and date of Commercial Item Description.TypeLengthP
19、ackaging requirements.a717.3 National Stock Numbers (N SNS). AlistofNSNs assigned thatcorresporid tothis CID. Thelistmay not be indicative of all possible NSNs associated with the CID.3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NSN LengthInchesI
20、 Type I Bastard-cut5110-00-241-7675 65110-00-260-0543 85110-00-241-9164 10Type 11 Second-cut5 11O-OOJ243-O938 65110-00-239-7556 85110-00-241-9165 10Type III Smooth-cut5110-00-241-9160 65110-00-241-9163 85110-00-241-9167 107.4 Keywords, File, Hand (American Pattern)MILITARY INTERESTS:NONE: DoD has no registered interestin revisions and amendments to thisCommercial Item Description until further notice,.A-A-2322A -!Preparing Activity:GSA-FSSProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
