1、 This document is restricted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 1 of 5 NAVISTAR, INC. TMS (TRUCK MATERIAL SPECIFICATION) NUMBER: TM
2、S-7099 TITLE: Fastener Tape Systems CURRENT REV No.: 0912 DATE: December 2009 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: Rev B-1, August 2001 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous ma
3、terials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use. Change Notice: Replace
4、d “International Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive; added CEMS B-50 requirement; editorial changes. Reference: File 16-7 Keywords: Fastener Tape 1.0 APPLICATION This specification covers synthetic fastener tapes or pads used for truck cab interiors. Various
5、styles of fastener systems are available and attachment may be achieved by sewing, mechanically, or by adhesive coatings. 2.0 SCOPE This specification covers the general requirements for color, roll length where applicable, adhesive backing if required, and colorfastness. Also included are the indiv
6、idual characteristics for one style (I) of tape. Other styles may be added to this specification if required. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the CEMS B-50 specification.
7、 3.0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referenced standards shall apply. The following standards, specifications and regulations are referenced in this specification. Quality System Standard ISO 9001 or TS-16949 AATCC TM 8 CFR Title 29, Section 1910 ASTM D 1682
8、NAVISTAR Manufacturing Std. MS-D-13 NAVISTAR Eng. Design Std. A-16 NAVISTAR CEMS B-50 NAVISTAR TMS-9543 4.0 GENERAL REQUIREMENTS The following general requirements apply to all styles of tape supplied to this specification. 4.1 Individual Characteristics 4.1.1 Style I Woven hook and pile fastener ta
9、pes (Formerly TMS-7099 Grade A or B Style 1) Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-7099 TITLE: Fastener Tape Systems REVISION: 0912 This document is restrict
10、ed and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 2 of 5 4.2 Construction Consists of a nylon hook tape and a nylon pile tape, each with a nylo
11、n ground. Two hook tapes are available (Grade A and B) with varying hook size and number of hooks per unit of area. GRADE A GRADE B Monofilament size (hook) 6.5 mil 8.0 mil Hooks per cm (in), min 55 (350) 27 (175) 4.3 Description Color, texture and finish of production material supplied must match m
12、aster samples of the pre-production material originally approved and on file in the Master Fabric Book in the Industrial Design Department at TDTC. 4.4 Roll Length (where applicable) Materials shall be supplied in 22, 45, or 90 m (25, 50, or 100 yd) rolls unless otherwise agreed upon by the supplier
13、 and using Navistar facility. 4.5 Adhesive Backing Adhesive backing, if required, shall be suitable for the intended application, providing adhesion to the substrate which exceeds the disengagement force of the fastener system. 4.6 Colorfastness: AATCC Test Method 8 Crocking test, performed both wet
14、 and dry, shall show no applicable staining of the contact fabric and have a minimum AATCC rating of four (4) when compared with the AATCC Color Transference Evaluation Chart. 4.7 Property And Performance Requirements 4.7.1 Tensile (Breaking) Strength: ASTM D 1682 The tensile strength of the individ
15、ual tapes shall be as indicated in Table I below: TENSILE STRENGTH, kNlbf( )MINIMUM WIDTH, mm (in) 50(2) 38 (1-1/2) 25(1) 18(3/4) 16(5/8) Grade A Hook Tape 096215.( )064145.( )051115.( )03885.( )03680.( )Grade B Hook Tape 096215.( )170(76.0056125.( )044100.( )03680.( )Pile Tape 096215.( )067150.( )0
16、44100.( )02965.( )02760.( )Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-7099 TITLE: Fastener Tape Systems REVISION: 0912 This document is restricted and may not be
17、sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 3 of 5 4.7.2 The following tests shall be performed on tape assemblies using the standard pile tape in combinat
18、ion with the two grades of hook tape. 4.7.2.1 Shear Strength (Lap Shear) Using an overlap of 76 mm (3 in), the shear strength shall be as follows: 4.7.2.1.1 Grade A Hook - 35 kPa (5 lbf/in) minimum 4.7.2.1.2 Grade B Hook - 41 kPa (6 lbf/in) minimum 4.7.2.1.3 Rate of loading shall be 30 cm (12 in) pe
19、r minute. 4.7.2.2 Lengthwise Peel Strength 4.7.2.2.1 Grade A Hook - 13 N/100 mm (0.75 lbf/in) width, minimum 4.7.2.2.2 Grade B Hook - 7 N/100 mm (0.40 lbf/in) width, minimum 4.7.2.2.3 Rate of loading shall be 30 cm (12 in) per minute. 4.7.3.3 Latching Strength Samples of the hook and pile tapes shal
20、l be affixed by adhesive to metal plates to form a sandwich consisting of the two plates with the tapes in contact with each other. The latching strength (force per unit area of tape contact) shall be determined by pulling in a direction perpendicular to the metal plates. 4.7.3.3.1 Grade A Hook - 35
21、 kPa (5 psi) minimum 4.7.3.3.2 Grade B Hook - 28 kPa (4 psi) minimum 5.0 QUALIFICATION Material and processes submitted for approval to this specification shall include the following: 5.1 A detailed, signed test report documenting testing to this specification per TMS-9543. 5.2 Test coupons or photo
22、graphs showing failure modes for each test. 5.3 The complete procedure used for preparing and curing materials for test, especially surface preparation and condition of the test specimens. 5.4 Questions regarding qualification requirements, reports and test materials may be directed to: Manager of N
23、on-Metallic Materials Materials Engineering and Technology Truck Development and Technology Center PO Box 1109 Fort Wayne, IN 46801 6.0 QUALITY All product supplied shall be clean and free from dirt, oils, sharp edges, or defects harmful to product performance. Copyright Navistar International Corpo
24、ration Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-7099 TITLE: Fastener Tape Systems REVISION: 0912 This document is restricted and may not be sent outside Navistar Inc. or reproduced without permission from
25、Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 4 of 5 7.0 SOURCE APPROVAL AND QUALITY CONTROL 7.1 Supplier Requirements All suppliers to Navistar are required to be registered to ISO 9001 Quality System Requirements. Navist
26、ar will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their certification with an accredited registrar and must furnish copies of registration certificates t
27、o their Navistar Corporate Buyer upon request. 7.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without
28、 approval. In the event that changes in material, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify Materials Engineering, Truck Development and Technology Center, and Navistar Purchasing and Supplier Development of the proposed
29、 change(s). Test data indicating conformance to all requirements of this specification, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. 7.3 Process Control The supplier shall
30、either perform and/or report results of tests on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier
31、 and the plant metallurgist and/or the quality control manager of the using Navistar plant may determine testing and reporting requirements on specific products. 8.0 SHIPPING, PACKING AND IDENTIFICATION Loading, packing, and identification shall be in accordance with Manufacturing Std. MS-D-13. 9.0
32、DESIGNATION ON DRAWINGS Shall include the color, width, style and grade (where applicable), and the adhesive coating system (where required). Examples: 1) Style I, Grade A, per TMS-7099 Color Width 2) Style I, Grade B, per TMS-7099 with pressure sensitive adhesive backing Color Width Copyright Navis
33、tar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-7099 TITLE: Fastener Tape Systems REVISION: 0912 This document is restricted and may not be sent outside Navistar Inc. or reproduced w
34、ithout permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 5 of 5 NOTE: 1. All drawings referencing TMS-7099A are equivalent to Style I (Grade A or B as indicated). 2. The adhesive backing system shall be selecte
35、d to meet the requirements of the intended application. 10.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. Truck D
36、evelopment and Technology Center 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ 11.0 APPROVED SOURCES (Style I) (Formerly TMS-7099A) Grade A Hook Tape Loo
37、p Tape 3M Company SJ-3400 SJ-3401 Velcro USA, Inc. #65 #1000 Grade B Hook Tape Loop Tape 3M Company SJ-3402 SJ-3401 Velcro USA, Inc. #80 #1000 A.0 GENERAL INFORMATION (Not a Requirement of the Specification) As indicated in the Application section, many styles of fastening systems are available, inc
38、luding variations in the attachment and/or the material (yarn). A.1 The methods of attachment of these fasteners are numerous, including sewing, use of pressure sensitive adhesives, solvent activated adhesives, heat activated adhesives, or by mechanical means. Selection of the particular attachment
39、system is dependent upon the design or application, the substrate, and the intended means of application of the parts being attached. A.2 Since the adhesive systems vary considerably in their applicability to varying situations, it is extremely important that they be selected with care, and the use
40、of parts already in the system in other applications be done only after careful consideration of the adhesive package. Definition of the particular adhesive system shall be included with the drawing covering each individual application. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
