IRAM 11 019-1957 《型号11019的柴油机轨道车启动用电容器》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DIN 69882-3-2005 de 9384 Tool holders with hollow taper shanks according to DIN 69893-1 - Part 3 Type B milling machine arbors with enlarged contact surface diameter for milling cu.pdf

DIN 69882-4-2005 Tool holders with hollow taper shanks according to DIN 69893-1 - Part 4 Type C holding fixture for parallel shanks with lateral driving surface - Dimensions《符合DIN .pdf

DIN 69882-5-2005 Tool holders with hollow taper shanks according to DIN 69893-1 - Part 5 Type D holders for parallel shanks with inclined clamping surface - Dimensions《符合DIN 69893-.pdf

DIN 69882-6-2005 Tool holders with hollow taper shanks according to DIN 69893-1 - Part 6 Type E clamping chuck for collets with 8 setting angle - Dimensions《符合DIN 69893-1的带锥形空心柄的刀具.pdf

DIN 69882-7-2005 Tool holders with hollow taper shanks according to DIN 69893-1 - Part 7 Type F expansion clamping chuck - Dimensions《符合DIN 69893-1的带锥形空心柄的刀具夹具 第7部分 F型膨胀夹头 尺寸》.pdf

DIN 69882-8-2005 Tool holders with hollow taper shanks according to DIN 69893-1 - Part 8 Type G shrink chuck - Dimensions《符合DIN 69893-1的带锥形空心柄的刀具夹具 第8部分 G型收缩夹盘 尺寸》.pdf

DIN 69888-2008 Requirements for balancing of rotating tool systems《旋转工具设备的平衡用要求》.pdf

DIN 69890-1-1990 Modular cutting tool systems protruding lengths of adapter modules adapter modules for spindle noses with 7 24 taper according to DIN 2079《组合刀具系统 连接器组件的伸出长度 符合DIN .pdf

DIN 69893-1-2011 Hollow taper shanks with flange contact surface - Part 1 Hollow taper shanks type A and type C Dimensions and design《带法兰接触面的空心锥柄 第1部分 A型和C型空心锥柄 尺寸和设计》.pdf