ITU-R RAPPORT 809-3 FRENCH-1990 INTER-REGIONAL SHARING OF THE 11 7 TO 12 75 GHz FREQUENCY BAND BETWEEN THE BROADCASTING-SATELLITE SERVICE AND THE FIXED-SATELLITE SERVICE《11 7-12 75.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

ASTM D4065-2012 Standard Practice for Plastics Dynamic Mechanical Properties Determination and Report of Procedures 《塑料动态机械特性的标准实施规程 程序报告及测定法》.pdf

ASTM D4066-2001a Standard Classification System for Nylon Injection and Extrusion Materials (PA)《尼龙注入及挤压材料的标准分类系统》.pdf

ASTM D4066-2013 Standard Classification System for Nylon Injection and Extrusion Materials (PA)《尼龙注入及挤压材料(PA)的标准分类体系》.pdf

ASTM D4067-2003 Standard Classification System for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods《增强和填充的聚苯硫醚(PPS)喷.pdf

ASTM D4067-2010 Standard Classification System for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods《使用ASTM方法的增强和填充的聚.pdf

ASTM D4067-2011 Standard Classification System for and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Usi.pdf

ASTM D4067-2016 Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using A.pdf

ASTM D4068-2001 Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane《隐蔽水容器隔膜用氯化聚乙烯薄片的标准规范》.pdf

ASTM D4068-2015 Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane《隐蔽水容器隔膜用氯化聚乙烯薄片的标准规格》.pdf