1、JEDEC STANDARD Thermal Shock JESD22-A106B (Revision of JESD22-A106A, April 1995) JUNE 2004; REAFFIRMED: SEPTEMBER 2011 JEDEC SOLID STATE TECHNOLOGY ASSOCIATION NOTICE JEDEC standards and publications contain material that has been prepared, reviewed, and approved through the JEDEC Board of Directors
2、 level and subsequently reviewed and approved by the JEDEC legal counsel. JEDEC standards and publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting
3、the purchaser in selecting and obtaining with minimum delay the proper product for use by those other than JEDEC members, whether the standard is to be used either domestically or internationally. JEDEC standards and publications are adopted without regard to whether or not their adoption may involv
4、e patents or articles, materials, or processes. By such action JEDEC does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the JEDEC standards or publications. The information included in JEDEC standards and publications represents a sound
5、approach to product specification and application, principally from the solid state device manufacturer viewpoint. Within the JEDEC organization there are procedures whereby a JEDEC standard or publication may be further processed and ultimately become an ANSI standard. No claims to be in conformanc
6、e with this standard may be made unless all requirements stated in the standard are met. Inquiries, comments, and suggestions relative to the content of this JEDEC standard or publication should be addressed to JEDEC at the address below, or refer to www.jedec.org under Standards and Documents for a
7、lternative contact information. Published by JEDEC Solid State Technology Association 2011 3103 North 10th Street Suite 240 South Arlington, VA 22201-2107 This document may be downloaded free of charge; however JEDEC retains the copyright on this material. By downloading this file the individual agr
8、ees not to charge for or resell the resulting material. PRICE: Contact JEDEC Printed in the U.S.A. All rights reserved PLEASE! DONT VIOLATE THE LAW! This document is copyrighted by JEDEC and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number o
9、f copies through entering into a license agreement. For information, contact: JEDEC Solid State Technology Association 3103 North 10th Street Suite 240 South Arlington, VA 22201-2107 or refer to www.jedec.org under Standards and Documents for alternative contact information. JEDEC Standard No. 22-A1
10、06B Page 1 Test Method A-106B (Revision of Test Method A-106-A) TEST METHOD A106B THERMAL SHOCK (From JEDEC Board Ballot JCB-04-57, formulated under the cognizance of the JC-14.1 Subcommittee on Reliability Test Methods for Packaged Devices.) 1 Scope This test is conducted to determine the resistanc
11、e of a part to sudden exposure to extreme changes in temperature and to the effect of alternate exposures to these extremes. 2 Terms and definitions dwell time: The total time the load is immersed in the bath. load: The specimens under test and the fixtures holding those specimens during test. NOTE
12、The maximum load is the maximum mass of specimens and fixtures that can be placed in the working zone of the bath while maintaining specified temperature and times. maximum load: The largest load for which the worst-case load temperature meets the timing requirements (see 4.1). monitoring sensor: Th
13、e temperature sensor located and calibrated to indicate the same temperature as at the worst-case indicator specimen location. NOTE The worst-case indicator specimen location is identified during the periodic characterization of the worst-case load temperature. specimen: The device or individual pie
14、ce being tested. transfer time: The elapsed time measured from removal of the load from one bath until insertion in the other bath. worst-case load temperature: The temperature of a specific specimen as indicated by a thermocouple imbedded in the body and located at the center of the load. JEDEC Sta
15、ndard No. 22-A106B Page 2 Test Method A-106B (Revision of Test Method A-106-A) 3 Apparatus The bath(s) used shall be capable of providing and controlling the specified temperatures in the working zone(s) when the bath is loaded with a maximum load. The thermal capacity and liquid circulation must en
16、able the working zone and loads to meet the specified conditions and timing (see 4.1). Worst-case load temperature shall be continually monitored during test by indicators or recorders reading the monitoring sensor(s). The worst-case load temperature under maximum load conditions and configuration s
17、hall be verified as needed to validate bath performance. Perfluorocarbons that meet the physical property requirements of Table 2 shall be used for conditions B, C, reworded to be consistent with Table 1. 2 Subclause 4.1, Timing 1stsentence; changed 10 seconds to 20 seconds. 2 Subclause 4.1, Timing
18、3rdsentence; reworded. 3 Clause 4 renumbered to clasue 5 Standard Improvement Form JEDEC JESD22-A106B The purpose of this form is to provide the Technical Committees of JEDEC with input from the industry regarding usage of the subject standard. Individuals or companies are invited to submit comments
19、 to JEDEC. All comments will be collected and dispersed to the appropriate committee(s). If you can provide input, please complete this form and return to: JEDEC Attn: Publications Department 2500 Wilson Blvd. Suite 220 Arlington, VA 22201-3834 Fax: 703.907.7583 1. I recommend changes to the followi
20、ng: Requirement, clause number Test method number Clause number The referenced clause number has proven to be: Unclear Too Rigid In Error Other 2. Recommendations for correction: 3. Other suggestions for document improvement: Submitted by Name: Phone: Company: E-mail: Address: City/State/Zip: Date:
