MSZ 4687-1958 《典型的数据和操作检测》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

BS 3SP 89-1983 Specification for characteristics boundary dimensions tolerances and static load ratings of airframe bearings《飞机机体轴承特性、界面尺寸、容差及静载荷等级规范》.pdf

BS 3T 53-1980 Specification for chromium-molybdenum steel tube (700 MPa) (outside diameter not less than 12 5 mm) (weldable)《铬-钼钢管材规范(700MPa)(管外径不小于12 5mm)(可焊接)》.pdf

BS 3T 60-1980 Specification for chromium-molybdenum steel tube (1150 MPa) (maximum thickness 8 mm)《铬-钼钢管材规范(1150MPa)(最大厚度8mm）》.pdf

BS 3TA 1-2009 Specification for sheet and strip of commercially pure titanium (tensile strength 290-420 MPa)《工业纯钛薄板材和带材规范(抗拉强度290-420 MPa)》.pdf

BS 3TA 10-2009 Specification for sheet of titanium-aluminium-vanadium alloy (tensile strength 960-1270 MPa)《钛-铝-钒合金薄板材规范(抗拉强度960-1270 MPa)》.pdf

BS 3TA 100-2009 Procedure for inspection testing and acceptance of wrought titanium and titanium alloys《锻造钛和钛合金的检验、测试和验收规范》.pdf

BS 3TA 11-2009 Specification for bar and section for machining of titanium-aluminium -vanadium alloy (tensile strength 900-1160 MPa) (limiting ruling section 150 mm)《钛铝钒合金棒材和型材的加工规.pdf

BS 3TA 2-2009 Specification for sheet and strip of commercially pure titanium (tensile strength 390-540 MPa)《工业纯钛板材和带材规范(抗拉强度390-540 MPa)》.pdf

BS 3TA 21-2009 Specification for sheet and strip of titanium-copper alloy (tensile strength 540-700 MPa)《钛-铜合金薄板材和带材规范(抗拉强度 540-700MPa)》.pdf