1、S-31.H MIL-F-5531 13 777790b 0365093 b m - _ MIL-F-85531(AS) 7 January 1986 MILITARY SPECIFICATION FIRING DEVICE, EXPLOSIVE ACTUATOR (ccu- 7 4 /B ) This specification is approved for use within the Naval Air Systems Command, Department of the Navy, and is available for use by all Departments and Age
2、ncies of the Department of Defense. 1. SCOPE. 1.1 Scope. This specification establishes the requirements for manu- facture and acceptance of the CCU-74/B Explosive Actuator Firing Device, referred to herein as the device. 2. APPLICABLE DOCUMENTS. 2. i Government documents. 2.1.1 Specifications and s
3、tandards. The following specifications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and suppleme
4、nt thereto, cited in the solicitation. SPECIFICATIONS MILITARY MIL-B-85251 Bomb, Binary Chemical, Empty (BLU-80/B) Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commanding Officer, Naval Air E
5、ngineer- ing Center, Systems Engineering and Standardization Department (SESD), Code 93, Lakehurst, NJ 08733, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document, or by letter. FSC 1377 AMSC N/A DISTRIBUTION STATEMENT A. Appr
6、oved for public release; distribution is unlimited. 0- THIS DOCUMENT CONTAINS 14- PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-5531 13 777770b 03b5099 U MIL-F-85531(AS) STANDARDS FEDERAL FED-STD-102 Preservation, Packaging and Packing
7、 Levels. MILITARY MIL-STD-105 Sampling Procedures and Tables for Inspection by At tributes . MIL-STD-109 Quality Assurance Terms and Definitions. Marking for Shipment and Storage. Identification Marking of U.S. Military Property. MIL-STD- 129 MIL-STD- 13 0 MIL-STD-453 Inspection, Radiographic. MIL-S
8、 TD-454 Standard General Requirements for Electronic Equipment. MIL-STD-810 Environmental Test Methods. M1L-STD-45662 Calibration Systems Requirements. 2.1.2 Other Government documents and drawings. The following other Government documents and drawings form apart of this specification to the extent
9、specified herein. Unless otherwise specified, the issues shall be those in effect on the date of solicitation. OTHER GOVERNMENT DOCUMENTS Code of Federal Regulations (CFR) 49 CFR 171-178 Transport at ion (Application. for copies should be addressed to the Superintendent of Documents, Government Prin
10、ting Office, Washington, D.C., 20402.) DRAWINGS Naval Air Systems Command (Code Ident 30003) i4 33AS864 Firing Device, Explosive Actuator, CCB-74/B . 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-F-8553L 13 m 9799906 0365045 T m SA1433AS115
11、1 SA1433AS1152 Firing Mechanism Fixture Firing Device. Firing Device Fixture Test Vibration. SA1433AS1166 Dent Block. (Copies of specifications, standards, handbooks, drawings, publications and Government documents required by contractors in connection with speci- fic acquisition functions should be
12、 obtained from the contracting activity or as directed by the contracting activity.) 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this speci- fication shall take precedence. Nothing in this specification, howe
13、ver, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3 . REQUIREMENTS. 3.1 Item description. The device consists of a housing and a lanyard- activated firing pin. 3.2 Characteristics. 3.2.1 Performance. During tail fin deployment, when a load is applied
14、 to the firing device lanyard such that the firing pin retracts and releases, the firing pin shall obtain a kinetic energy of 45 to 125 inch- ounces when the firing pin reaches the end of the firing device housing. 3.2.2 Environmental. The device shall not be damaged or its performance degraded afte
15、r exposure to the environments specified in 3.2.2.1 through 3.2.2.5. 3.2.2.1 High temperature. The device shall withstand exposure to a high temperature of +74 degrees Celsius (“Cl for 48 hours. 3.2.2.2 Low temperature. The device shall withstand exposure to a low temperature of.-48OC for 24 hours.
16、3.2.2.3 Temperature shock. The device shall withstand alternate sequen- tial exposure to temperatures of -48C and +74“C. L l. i i i 3.2.2.4 Mechanical shock. The device shall withstand exposure to half sine wave impact shocks having a peak amplitude of 15 gravity units (8) and a total duration of 11
17、 milliseconds (ms). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-8553 l(AS) 3.2.2.5 Vibration. The device shall withstand exposure to the vibration spectrum specified on Figure 1 in each of three mutually perpendicular axes . 3.3 Design an
18、d construction. 3.3.1 Production drawings. The device shall be fabricated and assembled in accordance with Drawing 143388864 and associated documents, and as specified herein. 3.3.1.1 Radiographic. The device shall show no evidence of defects and the internal construction shall be in accordance with
19、 Drawing 143388864 and associated documents. 3.3.2 Standards of manufacture. 3.3.2.1 Certification. When specified in the contract or purchase order * (see 6.2.2), the contractor shall prepare certification for the procuring activity, accompanied by objective quality evidence in accordance with MIL-
20、STD-109, that the materials, processes, and parts used in the assembly meet the applicable requirements for each item. 3.3.2.2 Working environments. Any special working environments for the manufacture of the device shall be in accordance with MlL-B-85251. 3.3.3 Marking. Each device shall be marked
21、in accordance with MIL- STD-130, with the manufacturers name or symbol, part number, and manu- facturers lot designation. The markings shall be in accordance with Drawing 143388864 and associated documents. 3.4 First article. When specified in the contract or purchase order, a sample shall be subjec
22、ted to first article inspection (see 4.2 and 6.2.3). 3.5 Workmanship. The device shall be fabricated in a manner that ensures compliance with all requirements of this specification and Drawing 143383864, fabrication and assembly practices shall be in accordance with MIL-STD-454, Re q ui reme n t 9 .
23、 Unless otherwise specified herein or on Drawing 143388864, 4. QUALITY, ASSURANCE PROVISIONS. 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order (see 6.2.1), the contractor is respon- sible for the performance of all inspection requirements as specified h
24、erein. (see 6.2.1), the contractor may use his own or any other facilities suit- able for the performance of the inspection requirements specified herein, Except as otherwise specified in the contract or purchase order 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without li
25、cense from IHS-,-,-O s a MIL-F-85531 13 W 9997906 0365047 3 = _ MIL-F-85531(AC) unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to assure supplies and services confor
26、m to prescribed requirements. 4.1.1 Responsibility for compliance. All items shall meet all require- The inspection set forth in this specification The absence of any inspection requirements in the speci- ments of Sections 3 and 5, shall become a part of the contractors overall inspection system or
27、quality program. fication shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. mance does not authorize submission of known defective material, either indicated or act
28、ual, nor does it commit the Government to acceptance of Sampling in quality confor- . defective material. 4.1.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspections (see 4.2). b. Quality conformance inspections (see 4.3).
29、 4.2 First article. When specified in the contract or purchase order (see 6.2.31, a first article inspection shall be performed on 15 devices manufactured using the same methods, materials, p;ocesses, and procedures proposed for production. Any production prior to acceptance of the first article sam
30、ple shall be at the risk of the contractor. 4.2.1 First article inspections. First article inspections shall be conducted on the first article sample and shall consist of the inspections of Table I in the sequence shown. 4.2.1.1 Acceptance criteria. The failure of one or more devices to pass any of
31、the first article tests and inspections of Table I shall cause rejection of the first article sample. 4.2,1,2 First article inspection report. When specified in the con- tract or purchase order (see 6.2.2), a first article inspection report shall be prepared for the procuring activity. The report sh
32、all contain the following infoFmation accompanied by certification (see 6.2.2) which attests that the information provided is correct and applicable to the pro- duct being submitted: a. A statement that the first article sample complies with all quality assurance provisions of this specification for
33、 the device specified in the contract or purchase order. I 1 I I. I 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-b. Number of units of product inspected. C. Results obtained for all inspections performed. d. Purchase descriptions or contract num
34、ber and date together with an identification and date of changes. e. Certificates of compliance of all material procured directly by the contractor. f. Date submitted. The certification shall be signed by a responsible agent of the certifying organization. of the agents authority to bind his princip
35、al. Substantiation of the agents authority will not be required with subsequent certifications unless, during the course of the contract, this authority is vested in another agent of the certifying organization. The initial certification shall be substantiated by evidence TABLE I. First article insp
36、ections. - _ Inspections Group I (100 percent) Visual/radiographic examination Group II High temperature Low temperature Temperature shock Mechanical shock Vibration Perf or mance Requirement par ag rap h 3.3.1, 3.3.1.1, 3.5 3.2.2.1 3.2.2.2 3.2.2.3 3.2.2.4 3.2.2.5 3.2.1 Method paragraph 4.5.1, 4.5.2
37、 4.6.1 4.6.2 4.6.3 4.6.4 4.6.5 4.5.3 i ./ I I l l l 1 I I I l I l 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-5531 13 M 977970b 03b50Lt7 7 4.2.1.3 First article verification. At the discretion of the procuring activity, first article test
38、s, or any portion thereof, shall be repeated under any of the following conditions:- a. be C. d. e. The manufacture has modified the product (such as change of raw materials, processes, production procedures, or methods) . Where there is evidence that the quality of the product has not been maintain
39、ed. accumulated product failures, of systems failures attributable to the product, or failure of the product to pass any of the tests for production lot acceptance that may be conducted by or for the procuring activity. This evidence may be in the form of When applicable documents have been amended
40、or revised suf- ficiently so that continued validity of the previous first article testing is quest ionable . When the manufacturer has not produced the product to this specification for a period of 12 months or longer. When the manufacturer changes the location at which the pro- duct is produced. 4
41、.3 Quality conformance inspections. The quality conformance inspec- tions shall be performed on each inspection lot and shall consist of the examination and tests listed in Table II in the sequence shown. e TABLE II. Quality conformance inspections. Inspections Group I (100 percent) Visual/radiograp
42、hic inspection Group II (sample) Vibratipn Performance Requirement pa rag rap h 3.3.1, 3.3.1.1, 3.5 3.2.2.5 3.2.1 Nethod paragraph 4.5.1, 4.5.2 4.6.5 4.5.3 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-F-C53L 13 7799706 0365050 3 W 4.3.1 In
43、spection lot. An inspection lot shall be in accordance with An inspection lot shall be formed from devices which have MIL-STD-105. passed Group I inspections. 4.3.2 Sampling. A sample shall be randomly selected from each inspec- The sample size shall be in accordance with MIL-STD-105 Normal tion lot
44、. Inspection, Inspection Level II, Single Sampling, and an acceptable quality level of 0.65 percent defective. 4.3.3 Acceptance criteria. Failure of one or more devices in the sample to pass any of the Group II quality conformance tests shall cause rejection of the inspection lot represented. i= 4.3
45、.4 Quality conformance inspection report. When specified in the n contract or purchase order (see 6.2.2), a quality conformance inspection report shall be included with each lot. following information accompanied by certification (see 6.2.2) which attests that the information provided is correct and
46、 applicable to the pro- duct being submitted: Reports shall contain the a. bo C. d. e. f. g. A statement that the lot complies with all quality assurance provisions of this specification for the device specified in the contract or purchase order. Number of units of product inspected. Results obtaine
47、d for all inspections performed. Contract or purchase order number and date together with an identification and date of changes. Certificates of compliance of all material procured directly by the contractor. Number of items in the lot. Date submitted. The certification shall be signed by a responsi
48、ble agent of the certifying organization. of the agents,authority to bind his principal. Substantiation of the agents authority will not be required with subsequent certification unless, during the course of the contract, this authority is vested in another agent of the certifying organization. The
49、initial certification shall be substantiated by evidence 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-F-5531 13 a 7797706 03b505L 5 - MIL-F-85531(AS) 4.4 Test equipment and conditions. 4.4.1 Standard test equipment. The contractor shall provide and main- O tain inspection and test equipment of sufficient quality and quantity to p
