1、a 1. I T a a - -. .F5#-9a - NIL-T-SLIL3A LI9 m 7999906 0257944 MIL-T-85413A(AS) 23 Januarv 1986 s U PERS ED N G-. MIL-T-85413(AS) 27 August 1982 MILITARY SPECIFICATION TEST SET, COMPUTER MEMORY LOADER-VERIP IER AN/ASM-607(V) GENERAL SPECIFICATION FOR This specification is approved for use within Nav
2、al Air Systems Command, Department of the Navy, and is available for use by all departments and agencies of the Department of Defense. 1. SCOPE. 1.1 Scope. This specification covers the general requirements for the manufacture and acceptance of the Computer Memory Loader-Verifier Test Set, AN/ASM-60
3、7(V), referred to herein as the MLV. This specification is to be used in conjunction with the applicable specification sheets and drawings listed in Supplement 1. 2. APPLICABLE DOCUMENTS. 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications and standards forra a
4、 part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications anci Standards (DODISS) and supplement thereto, cited in the solicitation. -4 Beneficial commc
5、nts (recoPPaendations, additions, deletions) and any pertinent data whck my be of use in improving thle document should be addreooed to: Conmianding Officer, Naval Aia Engineering Center, Syetems Engineering and Standardizafion Bepartment (SESD) Code 93, Lakehurst,NJ 08733, by using the self-address
6、ed Standardization Document Trnprovement Proposal (DD Form 1426) appearing at the end of .this document or by letter. 1 FSC 49201 DISTRIBUTION STATEMENT A: Approved for pub ic release; distribution is un1 imited. f . THIS DOCUMENT CONTAINS / 8 PAGES. Licensed by Information Handling ServicesCPECIFIC
7、ATIONS MILITARY MIL-T-18303 MIL-T-BYIJA 49 779790b Z579Y5 T MIL-T-85413A(AS) t for Test Procedures, Preproduction Acceptance and Life for Aircraft Electronic Equipment. Test Equipment for Use With Electrical and Electronic Equipment, General Specification for. MIL-T-21200 MIL-T-85 284 Test Set, Adap
8、ter Group, OF-65/ASM. (See Supplement 1 for applicable specification sheets.) STANDARDS FEDEM FED-STD-102 MILITARY MIL-STD-454 MIL-STD-46 1 MIL-STD- 104 MIL-STD- 7 8 1 MIL-STD-785 Form Preservation, Packaging, and Packing Levels . Standard General Requirements for Electronic Equipment. Electromagnet
9、ic Interference Character is tics Requirements for Equipment. Electric Power, Aircraft, Characteristics and Utilization of. Reliability Design Qualification Production and Acceptance Tests: Exponential Distribution. Reliability Program for Systems and Equipment Development and Produc tion. 2 License
10、d by Information Handling ServicesI MIL-T-85413A(AS) a MIL-STD-810 MIL-STD-1695 Environmental Test Methods. Minimum Standards for Working Environments. MIL-STD-45662 Calibration Systems Requirements. 2.1.2 Other Government documents, drawings, and publications. The following other Government documen
11、ts, drawings, and publications form a part of this specification to the extent specified herein. wise specified, the issues shall be those in effect on the date of the solici tat ion. Unless other- DRAWINGS Naval Air Systems Command (Code Ident 30003) 1164AS222 1164AS230 Test Set Adapter Group, OF-6
12、5/ASM. Test Set, Loader Verifier Computer Memory AN/ASM-OI(V). PUBLICATIONS Naval Air Sytems Command (Code Ident 30003) WS-6536 Procedures and Requirements for Preparation and Soldering of Electrical Connections. (Copies of specifications, standards, drawings, and publications required by contractor
13、s in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) . 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein the text of this speci- ficat
14、ion shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS. I 3.1 Specification sheets. The MLV requirements shall be as specified herein and in accordance with the applicable detai
15、l specification sheets. In the event of any conflict between requirements of this specification and the detail specification sheet, the latter shall govern. 3 Licensed by Information Handling ServicesMIL-T-BCIIA 47 H 7779706 0257747 3 3.1.1 Government-furnished equipment (GFE). The MLV shall operate
16、 in conjunction with the applicable Government-furnished software system installed on the MLV Magnetic Tape Memory (MTM) (see Drawing 1164AS320). Additional required GFE shall be further defined in all contracts and pro- curing documents (see 6.2.1). 3.2 First article. When specified in the contract
17、 or purchase order, a sample shall be subjected to first article inspection (see 4.2 and 6.3). 3.3 Characteristics. 3.3.1 Performance. The performance requirements for each MLV shall be as specified in the individual detail specification sheet. 3.3.1.1 Input voltages. The MLV shall operate from avai
18、lable aircraft power of 115 volts (Y), 400 hertz (Hz), 3-phase, under the steady state conditions specified in MIL-STD-704, for Category B equipment. 3.3.1.1.1 Current consumption. Current consumption shall be not greater than 1.0 ampere (A) through any input power connector pin during any mode of o
19、peration. 3.3.1.2 Electrical power. The MLV shall operate from a power source as specified in MIL-T-21200 for Class 2 equipment. 3.3.1.2.1 Protection, The MLV shall withstand input power variations imposed by abnormal electric system operations as defined in MIL-STD-704, and shall meet the applicabl
20、e sections of MIL-STD-704, Category B equipment, with the following exceptions: a. Normal system operation shall be defined for input power within the normal steady-state limits. b. Abnormal system operation shall be defined for variations of input power outside the normal steady-state limits. term
21、power irregularities (typically low voltages), the MLV shall display a power failure message to indicate abnormal power system conditions have been experienced and the operator shall be required to cycle the on/off switch. For short The MLV shall be capable of withstanding the transients of MIL-STD-
22、704 power sources. be a source of personnel injury) and not be required to function during abnormal power system conditions. The MLV shall be fail safe (any failure shall not cause or 4 Licensed by Information Handling ServicesMIL-T-854L3A 49 = 999990b 0257948 5 = 3.3.2 Environmental conditions. The
23、 MLV shall meet the requirements of 3.3.1 and the applicable specification sheet during and after exposure to the environmental Conditions of MIL-T-21200 for Class 2 equipment or the following or any natural combination thereof: a. b. C. d. e. f. g* h. i. ja High and low temperature extremes Altitud
24、e Shock Vibra t ion Humidity Salt fog Dust Explosive atmosphere 30-inch drop test Electromagnetic compatibility 3.3.3 Reliability. The contractor shall prepare a production reliabil- ity program plan, when specified in the contract, using MIL-STD-785 as a guide (see 6.2.2). This program plan shall b
25、e approved by the procuring activity prior to implementation. .3.3.3.1 Mean-time-between-failures (MTBF). The MLV, in conjunction with the MTM (see 3.1.1) shall demonstrate a minimum acceptable MTBF of 500 hours when tested as specified in 4.6. 3.4 Design and construction. 3.4.1 Production drawings.
26、 The applicable MLV shall be fabricate and assembled in accordance with the documents referenced on Drawing 1164AS230 and as specified herein. 3.4.2 Standards of manufacture. As a minimum, the MLV shall be manufac- tured, inspected, and tested under conditions and procedures meeting the requirements
27、 specified herein, and as specified on the applicable detail specification sheet. 3.4.2.1 Soldering. Procedures and requirements for preparation and soldering of electrical connections shall be in accordance with WS-6536. 5 Licensed by Information Handling ServicesMIL-T-C413A 44 m 477770b 0257744 7
28、MIL-T-85413A(AS ) 3.4.2.2 Special working environment. The facilities used in the manufac- ture, testing, and inspection of the MLVs shall meet the requirements of MIL-STD-1695 (electric assembly) Work Area 5. 3.4.3 Identification and marking. MLVs shall be identified and marked as specified on the
29、respective drawings. 3.4.4 Workmanship. The MLVs shall be fabricated in a manner that will ensure compliance with all requirements specified herein and on the respec- tive specification sheets. accordance with MIL-STD-454, Requirement 9. Fabrication and assembly practices shall be in 4, QUALITY ASSU
30、RANCE PROVISIONS. 4*1 Responsibility or inspection. Unless otherwise specified in the contract: or purchase order (see 6.2.11, the contractor is responsible for the Performance of all inspections specified herein. Except as otherwise specified in the contract or purchase order, the contractor may us
31、e his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government, The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ass
32、ure supplies and services conform to prescribed requirements, 41.1 Responsibility for compliance, All items must meet all require- ments of sections 3 and 5, The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absenc
33、e of any inspection requirements in the speci- fication shall not relieve the contractor of the respoksibility of assuring that oll products or supplies sumbitted to the Government for acceptance comply will till requirements of the contract, mance does not authorize submission of known defective ma
34、terial, either indicated or actual, nor does it commit the Government to acceptance of defective material. Sampling in quality confor- 4.1.2 Classification of inspections or tests. The inspections or tests specified herein are classified as follows: a. First article inspection (see 4.2). b. Quality
35、conformance inspections (see 4.3). c. Acceptance tests (see 4*4). 6 Licensed by Information Handling Services4.2 First article inspection. First article inspection shall be made on equipments representative of the production equipments to be supplied under the contract. The sample size and testing s
36、equence shall be as specified in the contract or purchase order (see 6.2.1). The tests shall be accomplished under the responsibility of the contractor and shall be conducted in accord- ance with the approved test procedure (see 4.2.2.4) in accordance with the tests specified in Table I. Contractors
37、 not having adequate facilities to conduct all required tests shall obtain the services of a commercial testing laboratory acceptable to the Government. 4.2.1 Scope of tests. The tests shall include all tests deemed neces- sary, by the procuring activity, to determine that the equipment meets all th
38、e requirements of this specification, the detail specification sheets, other applicable specifications and the contract. Within the limits specified in MIL-T-21200, first article tests shall include the f o 1 lowing : a. Acceptance test (see 4.4) b. Reliability assurance test (see 4.6) c. Environmen
39、tal tests (see 4.5) 4.2.2 Test procedures, provisions and equipment. 4.2.2.1 Maintenance and calibration. All test equipment shall be Cali- brated and maintained in accordance with a plan in accordance with MIL-STD-45662 (see 6.2.2). 4.2.2.2 Instruments and test equipment. All instruments and test e
40、quipment used for inspection and testing shall conform to the require- ments of MIL-STD-45662. 4.2.2.3 Test facility environment. Unless otherwise specified herein, or on the applicable detail specification sheet, tests shall be performed under the following conditions of environment: a. Temperature
41、: 25 i5 degrees Celsius (OC) b. Altitude: Elevation of test facility c. Relative humidity: 50 130 gercent 7 Licensed by Information Handling ServicesHIL-T-85q33A Li7 7779706 0257953 5 MIL-T-85413A(AS TABLE I. First article inspections. Examinations or tes ta Group A Visual and mechanical inspection
42、Group H Temperature shock Per f ormance High temperature Per formance Low temperature Perf ormance Altitude Performance Shock Per formance Vibration Per formance Humidity Per E ormance Salt fog Performance Dus I: Per formance Explosive atmosphere Per f ormance Requirement paragraph 3.4 3.3.2 3.3.1 3
43、.3e2 3.3, 1 3,3.2 3.3.1 3-30 2 3.3.1 3,3.2 3.3.1 3.3.2 3.3.1 3.3.2 3.3.1 3.3.2 3.3.1 3.3.2 3.3.1 3.3.2 383.1 8 Methods paragraph 4.7 4.5.1 4.4,1.3 405.2 4.4.1.3 4.5.3 4.4.1.3 4.5.4 4.4.1.3 4.5.5 4.4.1.3 4.5.6 4.4.1.3 4.5.7 4.4.1.3 4.5.8 4.4.1.3 4.5.9 4.4.1.3 4.5.10 4.4.1.3 - 8 Licensed by Informatio
44、n Handling ServicesMIL-T-854L3A 47 m 7777706 0257752 7 W MIL-T-85 4 1 3A (AS ) Requirement paragraph TABLE I. First article inspections. (Continued) Methods paragraph Examinations or tests 30-inch drop test Perf ormance Electromagnetic compa t ib i 1 it y Per formance Group C Reliability 3.3.2 3.3.1
45、 3.3.2 3.3.1 3.3.3 4.5.11 4.4.1.3 4.5.12 4.4.1.3 4.6 4.2.2.4 Test procedures. When specified in the contract or purchase order (see 6.2.21, the procedures used for conducting all tests shall be prepared by the contractor for procuring activity review and approval. The right is reserved by the procur
46、ing activity or the Government inspector to modify the tests or require any additional tests deemed necessary to determine compliance with the requirements of this specification and the contract. MIL-T-18303 shall be used as a guide for preparation of test procedures. When approved test procedures a
47、re available from previous contracts such pro- cedures may be used if approved by the procuring activity. However, the right is reserved by the procuring activity to require modification of such procedures, including additional tests, when deemed necessary (see 6.2.1). 4.3 Quality conformance inspec
48、tions. Unless otherwise specified in the contract or purchase order (see 6.2.1), the examinations and tests comprising quality conformance inspections shall be performed in accordance with 4.4. 4.4 Acceptance tests. The contractor shall be responsible for accom- plishing the acceptance tests. The co
49、ntractor shall make available the test procedure for procuring activity approval prior to testing. All inspection and testing shall be under the supervision of the Government inspector. Contractors not having testing facilities satisfactory to the cognizant technical activity shall engage the service of a commercial testing laboratory acceptable to the procuring activity. When specified in the contract or purchase order (see 6.2.23, the contractor shall prepare test reports showing qualitative results for all acceptance tests. Such reports shall be signed by an authori
