1、 AMSC N/A 1 of 14 FSC 1660 DETAIL SPECIFICATION SHEET CONNECTOR, OXYGEN HOSE TO REGULATOR Reactivated after 21 March 2005 and may be used for new and existing designs and acquisitions. This specification is approved for use by all Departments and Agencies of the Department of Defense. The requiremen
2、ts for acquiring the product described herein shall consist of this specification sheet and MIL-C-19064. CLASSIFICATION: - 1 ASSY - Type I (Figure 1) - 2 ASSY - Type II (Figure 2) Part or Identifying Number (PIN): MS22058-1 - Connector, Oxygen Hose to Regulator, Type I MS22058-2 - Connector, Oxygen
3、Hose to Regulator, Type II Unless otherwise specified, tolerances: decimals + 0.010; angles + 1 degree. MS22058D 21 March 2005 SUPERSEDING MS22058C 31 January 1986 INCH-POUNDProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS22058D 2 FIGURE 1. -1 ASSY
4、. FIGURE 2. -2 ASSY. -12 PIN, COVER (FLARE BOTH ENDS) -16 SPRING COVER -15 COVER -13 RING, SNAP SCREW NASM24693-5203 -23 YOKE (REF) -15 COVER -11 CONNECTOR, BODY -16 SPRING COVER -12 PIN, COVER (FLARE BOTH ENDS)-14 BRACKET ASSEMBLY -13 RING, SNAP -17 CLIP ASSEMBLY -20 STUD (REF) -11 CONNECTOR, BODY
5、-14 BRACKET ASSEMBLY Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS22058D 3 NOTES: 1. Material: Brass, ASTM-B16/B16M, 1/2 hard, UNS C36000. 2. Finish: Nickel plate per SAE-AMS-C-26074, class I, grade B. 3. Break sharp edges, 0.005 max radius. 4.
6、Surface texture in accordance with ASME-B46.1. FIGURE 3. -11 Connector, body. NOTES: 1. Material: Brass, ASTM-B16/B16M, 1/2 hard, UNS C36000. 2. Finish: Zinc plating, ASTM-B633, FE/ZN 13, Type I. FIGURE 4. -12 Pin, cover. .640+ .001 - .004 .093 DIA 1.562 .430 + .005 - .000 .025 + .005895 +.004 - .00
7、0 DIA .963 +.010 - .000 DIA .078839+.002-.000DIA .125.906 DIA 1.093DIA 63.047 RAD.156 1.031 + .005 DIA .2361.062 .800 +.008 - .000 DIA .768 +.000 - .003 DIA .0625+ .005 Dia x .125 Deep, both endsProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS22058
8、D 4 NOTES: 1. Material: Music/spring wire, ASTM-A228/A228M, ASTM-A313/A313M. 2. Finish: Passivate ASTM-A313/A313M per ASTM-A967. 3. Heat ring 500 to 550 degrees F for 20 minutes after forming. FIGURE 5. -13 Ring, snap. .063 Dia.062.875+ .000- .016 DIAProvided by IHSNot for ResaleNo reproduction or n
9、etworking permitted without license from IHS-,-,-MS22058D 5 NOTES: 1. Material: Steel sheet, ASTM-A366/A366M, Cold rolled; Steel bars, ASTM-A108, grade 1020. 2. Finish: Zinc plating, ASTM-B633, FE/ZN 13, Type I. 3. Remove all burrs and sharp edges. FIGURE 6. -14 Bracket assembly.SPOT WELD OR RIVET S
10、ECURELY TOGETHER .050 + .005SUPPORTHOLDER35.689 .031 RAD.875.218 (REF).109 RAD.188 .406 + .005.125 + .005 .098+.005- .000DIA1.00+.005 - .000 DIA .120 DIA 2 HOLES .188 RAD .500 RAD .219 .438 .500 1.000 +.005 1.375 .797+.016 - .000.688 RAD.9842 HOLES, IN LINE Provided by IHSNot for ResaleNo reproducti
11、on or networking permitted without license from IHS-,-,-MS22058D 6 NOTES 1. Material: Aluminum alloy, SAE-AMS-QQ-A-250, temper O, 0.051 thick. 2. Finish: Anodize, MIL-A-8625, Type I. 3. Heat treat after forming to SAE-AMS-H-6088, condition T4. 4. Remove all burrs and sharp edges, 0.010 min radius. F
12、IGURE 7. -15 Cover. .503 REF .635.219 REF .250 .031 R (TYP) .750 R .250 R .750 R .091 .488 R (TYP).015 R .031 R 1.400 .470 .188 (TYP) .112 (TYP) .031R 23 .109 RAD .098 +.005 - .000 DIA 2 HOLES IN LINE .184 +.000 - .010 LOCATION OF CENTERS FOR 0.31 BEND RADII .770 RAD .190 .875 .573R.226 .452 .103 (R
13、EF) .941 DIA Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS22058D 7 NOTES: 1. Material: Music wire, ASTM-A228/A228M. 2. Finish: Zinc plating, ASTM-B633, FE/ZN 13, Type I. 3. Number of coils: 7 4. Load not critical: Heat spring 500 to 550 F for fi
14、ve minutes after forming. FIGURE 8. -16 Spring, cover. .026 .312 + .005 .050 + .005 30 + 230 + 2 .125 .031 RAD .234 .094 .250 .116 + .005 I.D.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS22058D 8 FIGURE 9. -17 Clip assembly. -18 CLIP, LOWER -22
15、SPRING CLIP -21 PIN, CLIP (FLARE BOTH ENDS) -20 STUD FLARE STUD TO ATTACH YOKE TO UPPER CLIP -23 YOKE-19 CLIP, UPPERProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS22058D 9 NOTES: 1. Material: Steel sheet, ASTM-A366/366M, Cold rolled; Steel bars, A
16、STM-A108, grade 1020. 2. Finish: Zinc plating, ASTM-B633, FE/ZN 13, Type I. 3. All bends 0.016 radius unless otherwise specified. 4. Remove all burrs. FIGURE 10. -18 Clip, lower. 30 (TYP) 1.531.51610 .500 .844 .688 1.687 +.010 - .000 .062 (TYP) .438 DIA 4 FLANGED HOLES .406 RAD 1.9692.625251.031.750
17、.203 RAD .144+.000 -.010 DIA 2 HOLES IN LINE .172 RAD (TYP) .062 RAD(TYP).094 .031 .109 RAD (TYP).125.187 .328 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS22058D 10 NOTES: 1. Material: Steel sheet, ASTM-A366/366M, Cold rolled; Steel bars, ASTM-
18、A108, grade 1020. 2. Finish: Zinc plating, ASTM-B633, FE/ZN 13, Type I. 3. All bends 0.016 radius unless otherwise specified. 4. Remove all burrs. FIGURE 11. -18 Clip, upper. 2.6251.531.969 .516 .469 30 (TYP) .688 .812 1.625 +.010 -.000 .062 (TYP) 10.438 DIA 4 FLANGED HOLES.406 RAD 1.969.312+.002 -
19、.000 DIA 251.031.750.328 .187 .125 .203 RAD.144 DIA 2 HOLES IN LINE .175 RAD (TYP).062 RAD (TYP) .094 .031 .109 RAD (TYP) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS22058D 11 NOTES: 1. Material: Steel sheet, ASTM-A366/366M, Cold rolled; Steel
20、bars, ASTM-A108, grade 1020. 2. Finish: Zinc plating, ASTM-B633, FE/ZN 13, Type I. 3. Break sharp edges, 0.005 max radius. FIGURE 12. -20 Stud. NOTES: 1. Material: Brass, ASTM-B16/B16M, 1/2 hard, UNS C36000. 2. Optional material: Brass tubing, ASTM-B135. 3. Finish: ASTM-B633, FE/ZN 13, Type I. FIGUR
21、E 13. -21 Pin, clip. .310 DIA.0625 DIA x.078 DEEP .438 .123+.000 -.002 DIA.094+.016 -.000 .046+.005 -.000 .2031.562+.000- .002.125DIA+.003- .002.093+ .005 x .094 DEEP BOTH ENDS Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS22058D 12 NOTES: 1. Mat
22、erial: Music wire, ASTM-A228/A228M. 2. Finish: Zinc plating, ASTM-B633, FE/ZN 13, Type I. 3. Heat spring 500 to 550 degrees F for 20 minutes after forming. 4. Thirteen turns, close wound; load not critical. FIGURE 14. -22 Spring clip. .562 .562 12.3121.109 APPROX.174.080 DIA .312 Provided by IHSNot
23、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS22058D 13 NOTES: 1. Material: Steel sheet, ASTM-A366/A366M, Cold rolled; Steel bars, ASTM-A108, grade 1020. 2. Finish: Zinc plating, ASTM-B633, FE/ZN 13, Type I. 3. Break sharp corners, 0.005 max radius. 4. Threads shal
24、l be in accordance with FED-STD-H28. FIGURE 15. -23 Yoke. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. OMIT SLOTS IF MADE FROM BAR STOCK. +.010 - .000 DIA THRU .125 .168 DIA x 82 CSK.112-4 SUMF-2B2 PLACES .5
25、00 1.000 + .005 .141 .070 .062 (TYP) .219.062.031 RAD .185 RAD .120 DIA THRU .234 DIA x 100 CSKTHIS SIDE ONLY Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS22058D 14 Custodians: Preparing Activity: Army - AV Navy - AS Navy - AS Air Force - 99 (Pr
26、oject 1660-0834) Review activities: Army - GL Air Force - 11, 71 DLA - GS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
