NC 09-00-01-1986 Unified Elements System of Molds Dies Stampers and Machina Devices General Principies《浇铸统一原理系统 冲模，压模和机械装置 一般原理》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSK-M4D763-A5-2010 POLYCARBONATE + POLYBUTYLENE TEREPHTHALATE BLEND (PC+PBT) MODIFIED EASY FLOW HEAT OPTIMIZED MOLDING COMPOUND PAINTABLE TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSK-M4D764-A-2008 POLYETHYLENE (PE) FOAM CROSSLINKED CLOSED CELL 200 KG M3 TO BE USED WITH FORD WSS-M99P1111-A 《聚乙烯(PE)泡沫化学交联密闭槽 200kg m3 (与FORD WSS-M99P1111-A一起使用) [使用 FORD.pdf

FORD WSK-M4D765-A-2006 POLYPROPYLENE (PP) COPOLYMER HIGH MELT RATE FLOW MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A (Use WSS-M4D638-B)《高熔体流速的聚丙烯(PP)共聚物成型料 与标准FORD WSS-M.pdf

FORD WSK-M4D769-A-2008 ABS + POLYCARBONATE BLEND (ABS+PC) MOLDING COMPOUND PAINTABLE TO BE USED WITH FORD WSS-M99P1111-A 《可印刷丙烯腈-丁二烯-苯乙烯共聚物(ABS)+聚碳酸酯混合物(ABS+PC)中等抗冲成型料 与标准FORD W.pdf

FORD WSK-M4D771-A-2010 POLYPHENYLENE ETHER + POLYSTYRENE BLEND (PPE+PS) 10% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《10%玻璃纤维增强的聚苯醚+聚苯乙烯(PPE+PS.pdf

FORD WSK-M4D773-A2-2010 POLYARYLSULFONE (PAS) HEAT STABILIZED 20% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《20%玻璃纤维增强的受热稳定的聚芳砜(PAS)成型料 与标准FORD.pdf

FORD WSK-M4D775-A1-2014 POLYCARBONATE (PC) MOLDING COMPOUND EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSK-M4D775-A2-2014 POLYCARBONATE (PC) MOLDING COMPOUND OPTICAL GRADE EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSK-M4D775-A1).pdf

FORD WSK-M4D776-A1-2013 ACRYLIC (PMMA) HEAT RESISTANT OPTICAL GRADE MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf